No. The only way to get a shiny surface on the wood is by using a multiple coat, film forming finish. We don't recommend clear film forming finishes on decks because they are slippery when wet, they will eventually peel, and they are difficult to maintain and recoat. When properly applied, a penetrating finish like UV Plus will not be shiny, it will have a natural, matte look. For a glossy or satin appearance on vertical surfaces, we recommend our Timberflex products. back to top

On new homes the two coats of colored stain should be applied immediately after the roof is on, the windows have been installed and the logs cleaned prior to any chinking, if it is a chink style home, to prevent coloring the chinking. The clear top coat and subsequent clear maintenance coats can be applied later.

This is usually caused by oversaturation of UV Plus on the wood. Remember, UV Plus must be able to penetrate completely to work properly. Remove any excess material promptly. Within 48 hours of application, scrub affected areas with lacquer thinner or MEK solvent to soften excess material. Wipe dry. If product has cured to the point that this does not correct the problem, excess material must be removed by chemical stripping or sanding.

UV Plus for Pressure Treated Wood is a penetrating wood stain and oil finish that beautifies and protects exterior pressure treated lumber, providing a natural appearance. It is ideal for use on ACQ, CCA, Copper Azole and other types of treated lumber, and comes in a variety of tones and semi-transparent colors. UV Plus for Pressure Treated Wood contains fungicides and UV absorbers of the highest quality.

We get hundreds of requests for finish samples for customers who would like to "touch and feel" before they make their purchase. Unfortunately, it is not possible for us to mail out actual physical samples to all those who desire them. In many cases, our suppliers simply do not make samples, as the digital photography they use is very accurate.

Yes - We call the non-shiny ones, "Antique" - this gives them a 'blackened' or 'aged' look. The shiny ones can be found on our page of "Bright" buckles.

Yes, provided the previous finish has sufficiently weathered to allow penetration of UV Plus for Pressure Treated Wood. For best results, clean the surface with Wood & Deck Cleaner, or sand to a new surface.

We recommend surface and air temperatures between 45F and 90F. Avoid application in direct sunlight on hot days. If the wood is hot to the touch, it is too hot to apply UV Plus for Pressure Treated Wood.

Water beading is accomplished by adding waxes or paraffin to the stain. These additives do not last very long and are not good permanent water repellents, in addition to this they interfere with adhesion should you decide to paint over the stain. That's why we don't use them in our products. The high solids content of UV Plus fills the pores of the wood, providing excellent water repellency that will last.

One coat is sufficient for most applications. Severely weathered wood or rough sawn siding may require two coats.

UV Plus is a penetrating wood stain and oil finish that beautifies and protects exterior wood, providing a natural appearance. It is ideal for use on cedar, pine and redwood and comes in a variety of tones and semi-transparent colors. UV Plus contains fungicides and UV absorbers of the highest quality. It does not form a surface film when properly applied and is not subject to peeling and flaking. To recoat, just clean and/or brighten the wood surface and reapply UV Plus.

The copper weathervane will react to the elements of the weather and will slowly turn from a reddish-brown natural copper color to a darker brownish-black and eventually to the natural green patina finish. This process starts almost immediately with exposure to the elements and can take up to 10 years or so to complete - much depends on the weather conditions in your area.

Yes, we have a clear colour in VARIKOTE which when sprayed on to the colour you have applied will give it a more shiny look.

Wind Wonders sculptures can be cleaned with a reputable copper cleaner. If you want to protect it from the elements, a clear spray lacquer can be applied. IT IS CRITICAL that the sculpture be clean and dry when applying the lacquer. You MUST follow the manufacturer’s recommendation for application and drying time before putting your sculpture outside. You can also use car wax on the sculptures.

Absolutely! UV Plus for Pressure Treated Wood is an excellent choice for almost any exterior wood surface, including vertical surfaces. It can be used on siding, log homes, and wooden shakes. Make sure the surface is clean, dry, and any previous coatings have either weathered away or been removed. Do not use UV Plus for Pressure Treated Wood over paints or other film forming coatings, it's designed to penetrate into bare or weathered wood surfaces.

New pressure treated lumber should weather six to eight weeks minimum before applying UV Plus for Pressure Treated Wood. The wood needs to weather sufficiently to allow the pores to open up to accept the stain. Failure to do so will cause premature failure and possible surface sheen problems.

Clears do not protect the wood from damaging ultraviolet light, and do not offer much color retention. We suggest using a product pigmented with Transparent Iron Oxides, such as our UV Plus for Hardwood Decks. This allows you to maintain a natural look while providing UV protection and extended color retention to the wood. This is caused by oversaturation of UV Plus for Hardwood Decks on the wood. Remember, the product must be able to penetrate completely to work properly.

Our only clear finish is for interior use only. We would suggest the transparent wood finish designed for the type of wood you want to coat. (Examples: Cedar/Marine for cedar or teak; Transparent Redwood for redwood.) This indicates overapplication of the wood stain. In most cases, washing the surface with a solution of TSP (Tri-Sodium Phosphate) and water, (with some scrubbing) after seven days drying time, will correct the problem.

of course you may add what you would like but i can not be responsible for the condition of the block once it is shipped each block is hand milled, hand sanded and hand finished so each one is truly unique in its natural wood characteristics; certain imperfections are natural in hardwoods and in most cases add to the appeal and quality of a handcrafted item

Wind Wonders sculptures are made of 100% untreated copper. Untreated copper will travel through different hues of oxidation. Simply watch nature perform its own permanent patina. Mother Nature's artistic touch will vary depending on your geographical location and local climate conditions.

Some people wonder why wood should be finished at all. After all, some wooden structures have lasted hundreds of years. This is true, but not all wooden structures will last hundreds of years. Weather and the wood itself can develop rot and deteriorate to the point of collapse. Another thing to consider is appearance. If you think natural wood will retain its color, you are wrong. Sunlight turns all woods yellowish or brownish, then gray.