Solaris supports Digi InsideOut Networks' devices and recently, KeySpan and Prolific chipset based devices' support were also integrated to Solaris. Keyspan and Prolific USB serial drivers are available in Solaris Express dated 2/2006 and in Solaris 10 Update 2 and later. PL2303 chip based adapters and Keyspan USA-19HS adapter are available as part of Solaris 10 Update 2. Keyspan USA-49WLC adapter is supported in Solaris Express dated 3/2006 and will be available in Solaris 10 update 3.

Yes, but only Prolific based devices connected to an uhci controller are supported (ohci and ehci are not supported). this time, there are no secure USB commands to transfer data to or from a USB mass storage device. If you are concerned about USB security, please add the following lines to the file /etc/system exclude: drv/scsa2usb

Connecting the digitizer with Serial (RS232) or USB will be determined by the application software you are using with the digitizer. Please consult your application support for assistance.

Although serial to USB adaptors have reportedly worked, we cannot guarantee that the MicroScribe will communicate properly with the host machine using such an adaptor. For PC's: You have the option to upgrade your MicroScribe 3D to a MicroScribe G2 model, which is USB compatible. Check to make sure your software supports USB connection to the MicroScribe. Contact Immersion for more details. Yes, the MicroScribe G2 offers Mac compatibility.

This list is by no means exhaustive but attempts to cover as many USB devices as possible that are known to work under Solaris. Also, in addition to many new devices being introduced into the market each day, many may have undergone revisions or updates to their firmware or hardware even though they may be listed with the same model number or are no longer available.

Yes, but it will show up as a (very small) scsi disk. check /dev/dsk/c... nodes. There are no /dev/diskette nodes for usb floppy. Plug in the device and run rmformat(1M). It will show you the device node for the USB floppy. Assume it is /dev/rdsk/c4t0d0p0 (x86). # mkfs -F pcfs -o nofdisk,size=2800 /dev/rdsk/c4t0d0p0 # mount -F pcfs /dev/dsk/c4t0d0p0:c /mnt

Before inserting your USB memory stick, please log in to the machine directly (not via SSH from another system). Logging in at the console will ensure that the USB memory device is mounted with you as the owner. It is safest to insert the device into one of the USB ports on the front of the computer (rather than those on the back or on the keyboard).

Yes. A separate, Keyspan brand USB adapter can be purchased for your board. The adapter attaches to the end of the serial cable provided and then connects to your computer. The USB adapter can be purchased through GTCO or your local reseller.

The Sun Ray implementation of USB drivers is different from Solaris implementation. Please download the SRSS 3.0 for the latest Sun Ray support for USB devices. For device support details check: http://www.sun.com/io_technologies/sunray/sunray0.html. Are USB 2.0 devices from Quatech supported ? Currently only USB 1.1 devices from Quatech are supported. The current Sun Ray driver does not support USB 2.0 on the new Quatech devices SSU2-100, DSU2-100 and QSU2-100.

The exact error message looks like Could not find USB device (vendor 0x0000, product 0x0000). Make sure this device is connected to the computer You have to set up the permissions on your USB device correctly. See Section 4.3, "Setting up permissions for USB ports".

Most new customers purchase monitors with an internal serial or internal USB controller installed along with the touchscreen. One cable connects the touchscreen to an available COM or USB port. Elo also offers external serial and PC-Bus controllers. The external MX serial controllers can either be mounted to the back of the monitor or allowed to rest on a flat surface, and power must be supplied (typically by a wall-mount power supply), so there are more cables than with an internal controller.

Sorry, no. Today's PDAs do not host devices. They can only be slaves. Since our product requires a host, a USB adaptor won't work either. Currently we have no version that doesn't require a host.

Quatech has implemented a Low-Latency mode on all USB 2 devices. This setting can be found on the USB Serial Ports Advanced Options tab of the device manager. Each port can be set individually.

AutoEnginuity has verified our product with dozens of USB-to-Serial adaptors (IO Gear, Prolific, Belkin, etc.). This adaptor can also be purchased from us. Note: Not all USB-to-Serial adaptors are made equal. We have tried some based on the FDTI chipset (Cables Unlimited), KeySpan, the "<10$ eBay unit", and Radio Shack are NOT compatible. We highly recommend getting any of the above or anything based on the Prolific-chipset from a reputable company.

No. Although the OneTouch USB cable was more recently introduced, it is not considered an upgrade from the serial cable. Rather, it is a distinct product. The two types of cables are equivalent in quality.

NT4 does not have usb support, and we recommend our users to use either Win 98 or Win 2000. We can offer support for NT4 only for large customers under special conditions for our devices- including usb to serial or parallel.

You can go 5 meters or around 16 feet from a computers USB port or from a powered USB hub to a USB device. Back To Questions

The requirement is similar to that of USB 1.1, but all components will have to be USB 2.0 compliant. A successful USB...

Windows 98 default supports only USB 1.1. Install a USB 2.0 PCI adapter then USB 2.0 device still can work fine in Windows 98. Some device such as Micronet´s USB 2.0 adapter, it includes a USB 2.0 driver written by third party so it can work in Windows 98SE.

The WJ Readers can be configured in a serial TTL mode. Please refer to the application note “Controlling MPR Series RFID Cards in Serial Communications Mode”.

Not only will it not work, you may damage your device. In order for a device to work with USB it must be compatible and have appropriate drivers. Some early releases of the Freestyle Pro and Precision Pro were not USB compatible; if it did not come with an adapter you are out of luck.

The exact message looks like *** Error ('Could not claim the USB device') *** Could not claim interface 0 (Operation not permitted). Make sure no other program or kernel module (e.g. dc2xx or stv680) is using the device and you have read/write access to the device. You have to make sure that no such kernel module is loaded and that you have set up the permissions on your USB device correctly, such that you have (non-root) write access to the camera device.

the present time, we do not support any of the serial-to-USB adapters on the market due to major variance in their compatibility. There are a few Serial Amazing Box users that have used an adapter successfully, but it is a hit-or-miss guessing game as to which adapter will work with your particular computer’s configuration.

Both provide equivalent communication for all our meters. The distinction is that each kind of cable is intended for a different kind of connector to the computer. Some newer computers do not provide serial ports, which is why we introduced the USB version of the Interface Cable in 2004.

After I install the LEGO MindStorms Robotics Invention System 2.0 and USB Infrared Tower (IR Tower) software then plug in my USB IR Tower the Robotics Invention System software reports the tower is not connected. This can occur on some system if the device was not installed correctly or if there are problem devices in the Control Panel.

There are several ways to go about testing the product. The easiest way for Windows users is to connect a Loopback on the Port and use HyperTerminal to test it. HyperTerminal is included with Microsoft operating systems. If you don't see it listed in Program Manager, you may need to install it from the Windows CD. RS-422/485 Loopback Instructions

The USB specification allows for up to 127 USB peripheral devices to be used in a single system. Quatech 1-8 port adapters require one USB port, 16-port adapters require two USB ports. Thus, by using a series of hubs, up to 127 Quatech 8-port adapters or 63 16-port adapters can be used. This means that (using 127 eight port adapters) a single USB port can be used to connect 1016 serial devices.

Answer: Yes. You will need our USB connector from Agrowsoft if you with to use the USB port. You will need no additional connectors if you use a standard RS232 serial computer port. Answer: You can set up the software so that it sends text messages with both Alerts and a periodic "push" of current conditions. You specify the time interval (for example every 60 minutes). Your environments will be checking in with you rather that you having to check in on them!

The V.24 serial interface is quite simply best suited for this application. Its connection cable can be extended to almost any length and does not produce long-wave interference. USB has a maximum cable length of 8 metres and high interference levels. The same goes for other interface types. This is simply not true. See previous question. There may be radio clocks for which this applies; for the NeoClock it is not true. This is also not true.