Answer: No, James Hardie does not recommend Ezi-Grid® Tile Underlay as an Underlay in an external decking application. Our 15mm or 18mm HPC products must be used as specified in our Decking Construction Manual.

Answer: No, when a floor requires waterproofing an appropriate waterproofing membrane must be used as per Australian Standard for Waterproofing AS3740 Answer: No, Villaboard® Lining sheets are for wall and ceiling applications only, Ezi-Grid® Tile Underlay must be used in an underlay application.

Answer: No, James Hardie does not recommend Ezi-Grid® Tile Underlay be fixed directly to a concrete floor by nailing or gluing.

Answer: No, James Hardie does not recommend this method of fixing. You may consider other methods of floor materials or compounds to raise the floor level.

Answer: No, the nail is a 2.5 x 25mm Underlay Nail, which has been specifically designed for this application.

Answer: Yes, at 5 metres and in rooms where there is a change in direction, that is L-shaped rooms and at doorways.

Answer: Yes, you can use Ezi-Grid® Tile Underlay in all floor areas in a bathroom, as long as the product is waterproofed as per the manufactuers instructions. For further details on suitable waterproofing products, contact a waterproofing manufacturer.

Yes. There really is no limitation on using Maine Deck? in situations traditionally associated with timber decking.

The density used for the underlay depends on the quality of the fabric and the density of the design. Average values range between 12 to 20. When sewing on a stretchy fabric, it may be necessary to use a more dense underlay.

Underlay is used in order to stabilize an unstable fabric, so it may be necessary to use underlay when sewing on a stretchy fabric or garment. Zigzag underlay is recommended for use with unstable fabrics, whereas Guideline or Central underlay may be enough underlay.

Yes! The timber used by Timeless Timber comes from responsible producers who encourage proper management of resources. This involves the conservation of forests, and their renewal through re-planting schemes. Timeless Timber is also a member of the Timber Decking Association who strive for best practice in the decking industry.

You only need to replace any timber or woodwork that is damaged or rotten. If it is comparatively dry with a more or less even surface, it will be fine. The beauty of EPDM, is that you do not always have to strip of the old roof covering. If the roof decking is rotten or the felt is badly cracked and degraded, then you will have to lift up the old felt. If in reasonable level condition, then underlay can be laid over the existing felt and then the EPDM directly over the underlay.

Cabot does not recommend using Cabot Decking Stain or Solid Color Decking Stain on your siding. These stains are specifically formulated to withstand foot traffic and resist various spills and soiling. A better choice would be one of the Cabot products designed for vertical surfaces such as Cabot PRO.V.T. Solid Color Acrylic Stain or Semi-Transparent Oil Stain, which allow your siding to expand and contract with its exposure to heat and moisture.

underlay is a layer of white ink that we place under your design when printing on color shirts (basically a primer coat). The underlay provides a consistent color foundation, which helps ensure your chosen colors print correctly. It also helps prevent the darker shirt colors from showing through the ink. This step is treated as adding a color to your project's design costs, but if there is white in your design, we can use that screen for the underlay (usually in conjunction with a flash print).

Shingles shall be applied over spaced sheathing except where local building code requires solid decks for seismic regions, in wind-driven snow or high wind areas. Shakes installed with interwoven felt may be installed on a solid deck. Pressure impregnated preservative treated products may be applied with solid sheathing and you should check with your local Building Official for specific requirements in your area. See the CSSB's New Roof Construction Manual.

No problem. External application alone would give a good response. Internal administration combined with external application could hasten the process.

Not at all. Due to the extremely low moisture absorption rate water cannot have any deteriorating impact on Maine Deck?.

The job information questionnaires completed during the Discover Phase were used to develop benchmark jobs. These benchmark jobs were compared to the external labor market. The chart below depicts the job level or category and the geographic and type/size of institutions used for the comparison.

Our most popular timber is Paulownia which has been specially imported from its native Asia and is now an Australian Plantation timber, grown in four states of Australia. Paulownia resembles Western Red Cedar in weight and strength, increasingly being used in the marine industry. Recent tests at the University of W.A. have proven Paulownia extremely stable, termite resistant. The timber is gathering rave reviews world wide.

CCA is largely used to treat timber intended for outdoor uses such as home, school, and community playgrounds, decks, and landscape timbers. CCA treated timber is also used in building structures and other non-domestic uses such as telegraph and electricity poles. Wood that is freshly treated with CCA has a greenish tint, which fades over time. However, some other wood treatments may also have a green colour.

present we have no primary test evidence to demonstrate its performance in terms of screens. However, recent tests conducted small-scale show no loss in performance when carried out at small scale using non-insulating glass, further tests are planned for 2006-2007.

This rear panel connector can be used to insert modulation signals onto a carrier. In conjunction with modes such as AM, FM, SSB, Ext Mod can even provide communication signals at the SIG OUT connector.

You will need to consider all the use and conditions your application is going to subject the tile to. It is a good idea to list all your requirements and discuss with an experienced, competent professional.

The recommended product temperature at the time of application should be 70 degrees Fahrenheit. The minimum ambient and surface temperatures should be 50 degrees Fahrenheit.

Application rates vary depending on tile profile (low/flat, medium, high), roof pitch and uplift resistance required. Please contact the Technical Support Group at 1-888-868-1183 to obtain a copy of the TILE BOND Operating Instructions and Maintenance Booklet to view application rate details.

All you have to do is tell us where you want to use the tile and we can advise you which tile is best. We carry tiles for decorative purposes and tiles that can be installed in wet or dry areas. We want your project to last and bring you enjoyment for years to come.

Yes, when proper installation methods are followed. Exterior applications require special precautions and installation methods. Do not install floor tile on exterior walls unless the product specifically recommends this application.

To be used outdoors, the tile must be frost proof and unglazed for floor use. Make sure the absorption rate is 0.5% or less

Any tile can be used on the face of a fireplace. I would not recommend putting the tile directly In the firebox.