This can be a long answer, but to keep it simple; each speaker has a load resistance usually given in ohms. When you add speakers in parallel, jumping one to another, it lowers the ohms by half (i.e. - adding two 8 ohms speakers is a 4 ohm load on the amp). So back to the question; if in the amplifier specs it gives you the wattage for a certain load (Ohms), it is safe to run the amp at that level per channel.

For sound reinforcement (PA applications) one would typically feed the speakers with the XLR Main Outs. If you have monitors on stage typically one would use a pre-fader Aux Send to feed these. If you have a separate set of speakers in another room, like a cry room, or perhaps hearing impaired monitors, Mix B would be a good option. You could use any extra Aux Sends to feed those sources if needed as well.

I just removed one yesterday from the junk yard. It's the same procedure Matt D listed below. Just remove the the rear seat enough to lift the rear deck lid up around the speakers. There are three clips and three 8 mm bolts. I removed all three bolts and two clips. Then I went to the trunk and carefully pulled the speaker and amp assembly down. If you simply need to remove the speaker, that is even easier and can be done solely from the trunk. - /Bryan (91 SE), 6/16/01.

If the speaker are rated for 400 watts peak and are 8 ohms, then you can use an amp that is 400 watts (peak) per channel @ 8 ohms (an 800 watt amp). You can use a lower wattage amp, but you will be limited by the amp. You can also technically use a higher wattage amp, just don't use it a higher volumes which would drive the speaker over its wattage limit and potentially blow the speakers.

Be sure to purchase an amp with a wattage rating that falls into the wattage rating of your speakers. In other words, if you have speakers with a wattage rating of 10 - 80 watts, be sure not to get an amp with an RMS wattage rating of more than 80-watts per channel. Of course, you must also be sure that the amp you select is powerful enough for the way you like to listen (see FAQ on BLOWING SPEAKERS). As long as you purchase a receiver that your speakers can handle, you have a good match.

Each speaker is uniquely designed, timbre matched, and seamlessly coordinated in its own system; in order to ensure the most impressive sonic attribute and true cinema experience, we strongly encourage you to mix & match only in the same series of speakers. If your order includes 5 speakers, and one subwoofer, you are entitled to receive a set discount.

First take a look at the wattage of your amplifier. Figure a minimum of 20 watts of power per pair of speakers. Divide the wattage of the amplifier by 20 watts per pair to find the maximum number of speaker pairs that can be impedance matched for the amplifier. (Example: 100 amplifier - divided by - 20 watts per room = up to 5 pair of impedance matched speakers.)

On the rear of every amplifier there are either one or multiple output jacks. The outputs vary by model, but typically will be in the form of RCA, Speakon, Balanced XLR, and Banana binding post. Simply choose the output type on your amplifier and connect it to the input on your speaker.

Our Plug & Play Digital Systems allow you to educate patients anywhere, anytime without a computer. Each Digital System chip is custom made with the procedures you select. Simply plug them in and turn them on. Screen sizes range from 7" to 19" so they can be displayed tastefully in almost any size reception area or exam room. Many of our clients place them in spas and salons that refer patients.

This feature enables users to operate µfone dongle easily and effortlessly with no need to install or configure additional software. Simply plug in the dongle and begin to enjoy the freedom.

No. Using instrument cable to hook up your speakers can cause intermittent power loss, cause your amp to oscillate and damage the amp and/or your speakers. Please use 18 gauge cable or heavier (16, 14, or 12).

You can use amplifiers made by other makers, but the transitional characteristics of ECLIPSE system components, including the amplifier, are all optimised to faithfully reproduce the characteristics of the source sound. From this point of view, it is better to use an Eclipse amplifier.

Many Energy speakers have 2 sets of speaker level inputs, this is designed to allow for bi-wire or bi-amping. With the "jumpers" in place, one would connect these speakers like any other, simply by running speaker wire to the positive and negative inputs.

There are many schools of thought on this subject. Linn for example say that more should be spent on the source (CD player, Turntable) and less on the amplification or speakers. We on the other hand tend to think that balance is best; basically spend the same on each component. By doing this if you decide to upgrade your hi-fi at any time in the future you will know that your system will always be balanced. Also by balancing your system the features on your equipment.

r. Plasma TVs are connected to their main power source by a power cord from the back of the wall unit to a wall outlet or surge protector. There are also extensive audio and video connections that can be connected to various peripherals such as DVD players, VCRs, video cameras, video games, and the like.

You will need to add the modem's PnP ID to the PnP ID list in the serial driver. To enable Plug & Play support, compile a new kernel with controller pnp0 in the configuration file, then reboot the system. The kernel will print the PnP IDs of all the devices it finds. Copy the PnP ID from the modem to the table in /sys/i386/isa/sio.c, at about line 2777. Look for the string SUP1310 in the structure siopnp_ids[] to find the table.

The Home & Family Plug-in is simply the setup file that extracts and installs the Home & Family files on your computer. A 4-digit number follows the Plug-in file, which is your family's Account ID. For example: Plugin_0000. You can download your Plug-in from the Administration Area at anytime. Click on the Download Plug-in submenu of the Configuration link in the Home & Family Administration Area to download and install your Plug-in.

They use a modified UPnP for Rhapsody support in the 4.x versions but it is not documented or compatible with other UPnP efforts.

You do need an amplifier to play the Fretlight Guitar. No sound is transmitted via the cable that connects your Fretlight to your computer. That cable allows for the computer to power and control the light system. To hear the sound from the guitar's pickups, you will need to plug it in conventionally to a guitar amplifier with a 1/4" instrument cable (not included.

While the Ruby, Little Gem, and Little Gem MkII practice amps can be used with any speakers, best results are achieved with full-size speakers intended for use with guitar amps. The amps will work well with an total impedance of 4, 8, or 16 ohms. We've tried hi-fi speakers, clock-radio speakers, and auto speakers - they just can't cut it. For me, using anything other than a speaker designed for the frequencies of an electric guitar produced sounds more like a toy than an actual amp.

You need to take a few things into account here, the wattage of the existing amp and the total wattage of the existing speakers. As long as the amp wattage stays above the total speaker wattage after the additional speakers, there is no need to upgrade. Of course the other thing is weather the new speakers are to be zoned separately and if there is that availability on the existing amp.

No. The JDV is not a load box. This means that you must connect the amp to a load 1st (like a speaker) and then you can connect the JDV to the load.

For high efficient speakers, you need lower power to drive the speaker to desired sound level. In this area, we interpret the energy demand is correlated to speaker efficiency. For less efficient speakers, they are much power hungry, it is better to use muscular power amp. The fact is, each power amp specifies input sensitivity, it is the voltage that count.

No. Using instrument cables to connect your speakers can result in intermittent power loss, amp oscillation and speaker damage, as well as rendering the cables useless for any purpose. We recommend using 18-gauge or heavier speaker cables.

This web site features movie clips, songs, sounds, and other existing features that need certain programs to work. These software products go by different names, like "helper applications" and "plug-ins," and each will make your experience at this web site even more enjoyable. See your browser's help for more details.

Plug-ins are software modules which enhance your browser's capabilities. The plug-ins needed on this site allow your browser to display different types of audio or video content.

Note that if you simply want to disable the plug-in for a while, you can do this by unticking the "Enable SpamBayes" box on the front page of the "Manager" dialog. If you installed the plug-in from source, then you simply need to re-run the "addin.py" script, with the parameter "--unregister", and then delete the toolbar in Outlook.

For months I have been pondering the debate over whether or not to develop a simple straight ahead amp model that is stripped of the bells and whistles normally found on VHT amplifiers. After recently exploring the concept, I believe we have been on the right track all along. I have owned feature laden guitars and I discovered that all of the knobs and switches that you can throw on it won’t enhance the essence of the instrument one iota.