Many of today's cellular and digital PCS phones are equipped with RF ports which enable you to connect an external antenna to your phone. RF ports may be located on the back, bottom, top or side of your cell phone. Unfortunately some phones have no port that would enable to attach an external antenna to. NMO mounts are used to connect your antenna to your vehicle. Most NMO mounts are installed by drilling a hole in the roof of your vehicle. NMO mounts are typically offered as roof or lip mounts.

You can connect most phones to an external antenna by using an installable hands free kit that comes with an external antenna adapter. You can also purchase an external antenna adapter that allows you to connect the antenna directly to your phone. Some phones have an external antenna port. Other phones require that you remove your fixed antenna and insert an external antenna adapter to that port. Still other phones have no way to connect an external antenna to it at all. Read more here...

Yes, you may connect an external antenna at any time to your cell phone (if it supports an antenna connection) while it is connected to the Dock-N-Talk.

To connect to the Internet from your phone, you need a data plan and the necessary settings from your mobile operator.

Not all portable phones can connect to an extra antenna. It depends on your phone model and the availability of a connector to mate up with an antenna. There are many antennas to choose from. They include stubby antennas that are perfect for traveling, ¼-wave antennas you can use outside your vehicle, magnetic mount antennas for the top of your vehicle, and small antennas that suction to the window.

The PR-411 and PR-414 will feed two TV sets or one TV set and one FM radio. The PR-414 will also feed an AM Radio and it covers the shortwave AM band as well as the Broadcast AM band. If there are several sets on board, consider using one of our combination power box/amplifiers which will feed up to 8 TV sets. For larger systems and higher performance, consider our PR-420 and PR-422 antennas as used on Merchant Ships, Cruise Liners and by the Navy.

The MM2211 does not support an external antenna. The MM2211 uses a combination of vertical and horizontal antenna arrays to maximize connectivity.

Does a cell phone antenna emit dangerous radiation? Built in antennas for cellular phones improve reception while driving.

Does a cell phone antenna booster really work? Find out how antenna boosters for cellular phones can improve the strength of the signal received by your cellular phone, PDA or GPS satellite device.

First, contact your wireless service provider to find out what network your area is actually covered by (800MHz Analog, 800MHZ Digital, 1900MHz Digital, GSM). Although a phone may be capable of working on multiple networks, you want to determine what network you're actually using. If you're in a 800MHz range area (analog or cellular) you need a single band cellular antenna. If you're in a 1900MHz range area, you'll need a dual band antenna.

A few phones (such as Motorola Bag Phones) come equipped with a standard connector. Nothing else is needed. However, most phone RF connectors are not standard so they require an adapter.

Most business phone systems have a music on-hold input connection on the systems control unit usually located in a phone room or utility closet. The Ad-Hold player, either a standard CD player or Digital On-Hold player easily connects to this music on-hold input. Normally a phone service technician is not required.

Simply find the “gadget person” in your office. You know… the technology “go-to-person”. Hand them the equipment and our one page installation guide. By the time the kettle has boiled your message will be playing. If you’ve never had anything playing on hold before, make sure you let us know. In this case, you may need to get a real “go-to-person” to install it for you.

Yes - There are several phones that allow you to connect or ???tether??? your phone to your computer via a data cable. This will allow you to use your phone as a modem to connect to the Internet. This would allow you to connect to the Internet while you are on the go and in one of Verizon Wireless???s National Enhanced Service Areas. You will need to purchase some additional software and a cable to connect to your computer.

Generally, no. Because of the high frequencies involved, special coax suitable for microwave use is required to keep the losses low. Several people have asked if they can substitute RG-58, RG-8 or RG-214. These coax types have unacceptably high losses at these frequencies. People occasionally ask about 75 ohm TV/satellite coax as well (RG-62), which is a definite no-go because of the incorrect impedance. Belden 9913 is questionable because of "water piping" problems.

No; we wanted to make this series of product as simple as possible, Usually the engineers at Alinco think of adding features to the radio, but for these models they started with subtracting the features from the current full-feature HT. We know it's missing CTCSS decode, DTMF encode, external antenna connector, multi-function keypads, wide-band RX coverage, etc, but DJ-S series offers the go everywhere, easy to use, best valued Ham radio equipment ever made.

The LG5350 and Sanyo 6400 are reported to have serial port circuitry. The other Vision phones only support a USB connection, so they cannot connect to a PDA's serial connection. Despite the fact that USB stands for "Universal Serial Bus," the USB standard is quite different from a serial connection. The critical distinction for the cell phone situation is that USB requires both a host (aka a "root hub") and one or more clients.

The Thuraya satellite phone user terminal operates on a dual frequency of GSM 900 MHz and satellite at a 1.6/1.5 GHz range and therefore requires additional hardware for such dual band operations. The Thuraya satellite phone uses a Quadrifilar helical L-band antenna consisting of helices wound on a cylinder, which give it a larger in size compared to normal GSM antennas.

Most Australian capitals have their own dialup access number. Customers outside capital cities should use the National Data Number. It's important to ensure the number you are dialling is a local call, otherwise you may end up paying national or STD call rates.

No, this is a completely different technology to 3G and Bluetooth - this provides faster, more reliable and much cheaper access to the Internet.

If you have paired the BLUEPEARL with more than one device, it will try to connect to the last known device.

To visit a WAPsite you need to use the internet browser on your mobile phone. How this is done depends on the make and model of your handset, please check your user manual or contact your service provider (Vodafone, O2, Orange...) for help in setting this up. If you are a trying to understand how to configure your phone for WAP please contact your mobile network's helpline:

Most phones with an external antenna port can be connected directly into the amplifier. We carry a full line of adapters for $19.95; see the complete list here. The amplifier can also be connected to a hands-free car kit, PBX, Tellular or any cellular system that has an external antenna port.

Voice T1s can be terminated in a number of fashions but additional equipment is almost always required. If a PBX (Private Branch Exchange) phone system is being used, a T1 line card can be purchased to integrate it into the phone system. If a system is not being used, a T1 channel bank will split out the 24 channels so that they can be used like traditional phone lines. Voice T1 lines are normally delivered via a jack provided by the local phone company; this jack is normally a RJ-45.

In theory any SyncML enabled device should be able to synchronise with the University's Calendaring service, but this has not yet been tested.