We have everything needed to refinish a tile floor. First you would mop a liquid floor stripper on the tile. Allow it to sit for 5 minutes or so and scrub the floor with a floor buffer equipped with a stripping pad. The next step is to mop the floor with clear water. It may be advisable to mop it twice so you are sure that all the stripping product and dirt is off the tile. When dry, the floor should look clean but dull. Then apply the floor wax.

Wax Stripper is a super fast acting acrylic wax stripper without the undesirable vapors of ammonia. This biodegradable formula comes in a concentrated industrial strength. Dilute with water according to package directions.

No. As long as the existing finish is not changing color and the floor is clean of any dirt and debris, you can recoat without fully stripping the floor.

Our technicians do not install floor tile, but we can recommend and coordinate with tile contractors to give your bathroom a completely new look.

No wax, no mess. Mohawk Hardwood Floors are very easy to maintain. Simply use Mohawk Floor Care Essentials Hard Surface Cleaner and a specialty terry cloth flooring mop available from your local Mohawk flooring store. See the Store Locator for a Mohawk flooring dealer nearest you.

Never wax tile. Your tile surface is lustrous enough as it is. When you use waxes, you are simply wasting your money and causing unnecessary build-up which sooner or later will have to be stripped.

Typically the removal and disposal of that type of asbestos containing material is not regulated by EPA (even commercially) if it is in good condition. If the material can be taken up with no significant breakage, there is little risk for fiber release.

You can do this several different ways. 1- A Wireless router. 2- Add ethernet cabling (using an electricial or other low voltage wiring contractor). 3- Request a new data drop - here is how you do that: Call Harbornet as far in advance as you can and ask us to schedule an appointment for you to move your data outlet. You can also select Customer Care from our website and then choose the "Line Move or Address Change Authorization Form". The direct link to this location is https://www.shoppingnw.

It's time to apply the Floor Tile Sealer to seal and prolong the life of resilient tile, linoleum, terrazzo, brick, quarry tile, and concrete floors.

Yes you can lay timber over concrete. If the concrete slab is less than five years old, we can apply a membrane between the slab and the timber so as the moisture from the slab doesn't damage the timber.

Yes, it is possible. However, there are some conditions which must be adhered to. Existing floors must be overlayed with at least WBP grade plywood. However, marine ply is best. It must have a minimum thickness 19mm, screwed down (not nailed) at 150mm centres. All timber surfaces should be primed on the reverse side and all edges. It is essential that one uses powdered adhesive with a latex additive when tiling onto plywood.

Yes, when proper installation methods are followed. Exterior applications require special precautions and installation methods. Do not install floor tile on exterior walls unless the product specifically recommends this application.

Ceramic tile in either glazed or unglazed form do not need to be sealed. These products are impervious to moisture and topical sealers will not properly adhere to them. Also, you can not change or alter the appearance or the sheen of a ceramic tile by adding a sealer. Therefore, a sealer in not recommended for glazed and unglazed surfaces.

Tile mosaics are a wonderful, lively addition that complements the appearance of your pool. They can be selected and ordered upon your visit to choose waterline tile.

No, we do not recommend doing this, as a wall is generally a P.E.I. 1 tile, that is it has a very low wearing and will not last very long.

Wall tiles are generally more porous, which helps with their adhesion to walls, the glaze is used more for the appearance, and is resistant to detergents etc. On the contrary, floor tiles have low porosity, with low to medium water absorption, which will give them better technical characteristics, as the glaze is more than the look, it is also used to prevent wear and promote scratch resistance.

We would prefer that you did not. Floor heating systems are professionally installed through our trained personnel.

Water and oil will bead up on your floor when sealed as recommended in our Installation Specification Guide. You need only mop it up with a sponge. For routine cleaning vacuum or sweep it, as you would any other natural stone floor or a wood floor. To wipe up, use a non-acid based cleaning product. Warm, soapy water is also fine. AquaMix makes a tile cleaning product, Concentrated Stone & Tile Cleaner, which can be used on your floor. Check their website at www.aquamix.

If the structure of the counter is strong enough to support the weight of the heavier floor tile, then this should be fine.

A tile, whether it be ceramic, porcelain or natural stone is usually a good retainer of heat. Therefore it can often be the warmest floor in your home or building. It depends on the air temperature under the floor and the exposure to sunlight etc. Under-floor heating is a good option to warm your floor but it???s real intention is to provide an efficient, effective heating solution that gives you comfort throughout your home, therefore fulfilling your complete heating requirement.

You can use a two part ???rubber based or latex modified??? flexible adhesive to tile directly onto the timber. (Ensure the product chosen is manufactured specifically for this purpose). The timber will need to be clean and stable. (You will need to confirm floor joists and spans will be acceptable). This option is best suited when there are concerns of adding extra height to the existing floor and/or in smaller areas not subject movement or high traffic.

No paint must be removed off of a concrete floor before tile can be applied. Removal of Paint can be done by scraping it or a shot blaster machine.

If the floor is cracked it is advisable to use an anti-fracture membrane, otherwise cracks may transmit through the tile. Also as stated in question #2 you cannot tile over a painted concrete floor.

Do not use household dust treatment chemicals on the tile. Use a vinyl floor cleaner and separate finish. Both must be water-based. Vacuums: Do not use a beater brush on a vinyl floor. Use the proper solid floor attachment for vacuuming. NO WAX! Do not wax a vinyl floor. All of our vinyl flooring contains a no-wax finish. The flooring is non-porous and will not absorb wax. It will build up and collect even more dirt.

Yes. However, tile will not bond directly to a wood floor. We recommend the following methods to prepare your wood floor for tile installation: Install Schluter Ditra, from Schluter Systems, with a latex thinset. Then install the tile using a non-latex thinset.

Yes. If the old tiles are high-gloss, we recommend sanding them down first to increase bonding strength. Then use a high-strength latex thinset to install the new tile.

No. Wall tile has a lower breaking strength than floor tile. By installing wall tile on floors, you run the risk of the tile cracking or breaking over time.

The Ronald McDonald Family Room is a comfortable rest area for families at the IWK Health Centre. It is more than just a room - it has a large living room, kitchen/dining area, an art room, and four bedrooms - almost like a mini Ronald McDonald House. And, just like Ronald McDonald House, the Family Room will be staffed -- a full-time coordinator and volunteers will provide support and security.

The Ronald McDonald Family Room will have only one purpose - to be a comfortable rest area for families at the IWK Health Centre.