The DRYAIR Heat Exchanger has been designed to eliminate "Hot spots" in a building by using high air flow. Example: a direct flame burner of equivalent size or rating will output 236 L/sec of air at 205 °C while a DRYAIR PHE-60EU portable heat exchanger will output 1,085 L/sec of air at 49 °C. This is an equal amount of KW output, but the effect is different.

Blaze King gas appliances are unique to the industry in that most Blaze King gas models have heavy-duty heat exchangers. Superior engineering and design has allowed Blaze King to fit the maximum amount of square inches of surface area of heat absorbing steel into each model. The more surface area of steel, the more energy absorbed during the combustion process. Then, the variable speeds fans that are standard in all gas models then moves that heat into your home.

Air-to-air heat exchangers, and/or other types of mechanical ventilation are recommended in all tight houses, including those constructed with Universal Foam Tech, Inc. panels. Universal Foam Tech, Inc. recommends that air-to-air heat exchangers be incorporated into all Yes. A study by the Energy materials Testing Laboratory has show that EPS insulation does not absorb appreciable moisture, even under conditions characteristic of prolonged, cold, damp winters.

Whenever you have a heat exchanger, you must have a temperature difference in order to force the heat to cross the heat exchanger barrier and go to the other fluid. No heat is really lost, but the heating unit may run a little less efficiently at a the higher temperature.

Solution: The exterior termination cap on your exhaust system must constantly be free of any element that could block it, such as snow, ice, bird nests, etc. Sometimes, wind may cause a turbulence zone that will cause the burner and the pilot to shut off. If your burner or pilot flame has gone out during a very windy day, there may be nothing wrong with your fireplace. Simply re-light the fireplace. Solution: B-Vent gas fireplaces have a thermal switch.

There may be a blockage in the orifice or pilot tube. Bugs and spiders get into the pilot assembly, venturi tube and burner ports causing the unit to either not light or perform poorly.

That depends on a number of factors. The discharge temperature is determined by the temperature and relative humidity of incoming air. To determine the temperature of the air leaving the cooler, you will need to know the outside dry bulb temperature, the current outside wet bulb temperature, and the evaporative efficiency of the evaporative cooler (typically provided in product brochures under Performance Data). This should provide a guide to approximate discharge air temperatures.

Unfortunately, there are three kinds of service companies out there. The kind that just wants to sell you something whether you need it or not, the kind who are just plain incompetent and there are companies that only sell you what you need, like Hi Ho Petroleum. One good rule of thumb is to get a second opinion. Anyone who pressures you to replace a part might not have your best interest in mind. On the other hand, your equipment may be dangerous to operate.

It's not recommended. Thermal fusion of the pipe, drilling and trenching are procedures best handled by licensed professionals. Nonprofessional installations may result in less than optimum performance, which could cancel out anticipated savings

The heat exchanger is the area of the furnace where "heat" is exchanged-from the fire at the gas burner to the air that is recycled into the home through the duct system. The heat exchanger is sealed so that the products of combustion from the gas burner never come into contact with the air that goes back into the home.

Geothermal earth loops are made from High Density Polyethylene, (HDPE) pipe. The circuits are either 3/4" or 1 1/4" diameter and headers are either 1 1/4" or 2" diameter. The resin is PE 3408 having a cell classification, 345564 or 345434 per ASTM Standard Specification D3350, certified as being in accordance with CSA Standard B 137.1. This is the specification referred to in CSA 445 and CSA 448 and thus is mandated by Canadian Building Codes.

It is not recommended. In addition to thermal fusion of the pipe, drilling and trenching are procedures best handled by licensed professionals. Nonprofessional installations may result in less than optimum performance, which could cancel out anticipated savings. Also, warranties are usually void if the system is installed by a non-authorized dealer.

Summary: The output temperature will depend on the ambient temperature and humidity. See the Humidity Index if you know the range of your typical ambient temperature and humidity. Basically all Swampys except the Ice Models operate the same so choose the one that fits your needs regarding dimensions, airflow direction & use.

The air circulation within your home may be good, but more likely the air quality is poor. It's damp, stuffy, or making you sick. Replacing appliances such as a furnace or water heater, installing new windows or adding siding to a home changes the air leakage rate. Any improvements made to a home that reduces airflow in a house may result in insufficient natural ventilation. Excess moisture destroys your windows and building structure.

The HR 2.5 and HF 3.0 units require a floor or pipe drain to evacuate the water produced by the functioning of the unit. They should be installed within an area of the house where the ambient temperature is above 10°C) (basement, furnace room, closet, etc.).

Answer: it is indicated by “HI”, while the simmer flame is indicated by “LO”.

A portion of the heating thermostat pumps' electrical energy is lost to the bath liquid in the form of heat. Pump output flow, thermostat insulation, and the type of bath liquid used may affect the increase in bath temperature. Some bath temperatures can increase as much as 70°C above ambient temperature; however, Lauda® Ecoline Circulators only heat the bath slightly above ambient temperature when the lowest pump flow setting is selected. Yes and no.

If your Serial number starts with an S or an E, that would determine that you have either 321 SS Ht. Exchanger or 409 SS Ht. Exchanger. Heat Exchangers fabricated from 409 SS are magnetic.

Because the thermal conductivity is so high - it is 23 x better than stainless steel or titanium and 1.6 times better than aluminum.

Answer: Yes! The flame and heater operate independently of each other. This means you can enjoy the ambiance of of a realistic flame all year round!* *In many gas units, the flame cycles off as the room temperature rises and you lose the flame effect until the room cools down again. In smaller rooms, gas fireplaces can be off a lot of the time and in the warmer climates they may not come on at all unless the thermostat is set higher than the room temperature

Yes, the Symphonytm flame and heater operate independently of each other. this means you can enjoy the ambiance of a realistic flame all year round!* In many gas units, the flame cycles off as the room temperature rises and you lose the flame effect until the room cools down again. In smaller rooms, gas fireplaces can be off a lot of the time and in warmer climates they may not come on at all unless the thermostat is set higher than the room temperature.

No. Air cooler is another kind of air processor, it does not include air compressor, but only make out cool wind by water cycle system; Air conditioner is work with air compressor system. It is the difference. However, our air cooler not only with cooling and heating function, but also has another function, such as purifier, humidifier; additional function such as anion generator, calendar and so on.

The jets blow cold air through the water to create the bubbles and this cools the water down. We recommend using the hydrotherapy jets sparingly.

The jets blow cold air through the water to create the bubbles and this cools the water down. We recommend using the turbo jets sparingly.

Heat and sunlight, even minimal exposure can change the color of a crystal. There are pieces that are more susceptible to color change such as amethyst and fluorite, and to some degree citrine.

Both buildings have central heating and air conditioning. The temperature is controlled via central thermostats located on each floor of each building. The heating and cooling system is well-maintained. In fact, some people have been known to even open their windows in the summer because it is too cool for their taste.

The Cooler Pack (CA24) has heavy-duty velcro straps that wrap around the wood stake sides of the wagon.

Every circulator incorporates a circulating pump, which ensures thorough mixing of the bath liquid inside the bath and also pumps the bath liquid through an external circuit. The electrical energy taken up by the driving motor passes as thermal energy into the liquid, which leads to a slow temperature rise inside the circulator up to the so-called intrinsic temperature. The intrinsic temperature depends on the pump output, the insulation of the circulator, and on the bath liquid used.

Not usually. Capacity is limited by the amount of air that the burner can pass. Increasing pressure to pass a larger quantity of fuel, when insufficient air exists for the larger capacity, can be dangerous. In some cases, increasing fuel pressure above the maximum can cause burner instability. Further, the need for increased pressure may signal dirty (fouled) tips, which can also lead to burner instability.