Clear spray lacquer is available at most hardware stores. Wood stains vary greatly. Natural oak is sealed and lacquered only. Also available is cherry, stained oak, antique oak, etc. RETURN TO TOP

Answer: All the Magnums have the same thickness on their cabinets as follows: the top deck is 3/4", the bottom deck is 1/2", and the front apron is 5/8".

The clear coat finish gives your vehicle a "showroom shine" and protects the base coat from damage. ECO advises you to regularly clean and condition your vehicle's clear coat finish to ensure ultimate protection and luster.

The best way to protect your vehicle's clear coat is to visit one of ECO's many locations on a regular basis. Regular application of our Double Clear Coat Sealant creates a barrier that helps protect your vehicle's finish from harmful UV rays and airborne contaminants, as well as acids, tree saps, bugs, and bird droppings...All of which cause damage to your vehicle's factory clear coat. Our protective sealant lasts up to 30 days on your vehicle's finish.

Walbernize is a type of wax that has been used on Airstream Plasticoats since the first trailer was coated. Should be applied two times a year, more if you want. It was first used by Airstream when they were transporting trailers. They applied it to the front of the trailer so that when bugs and dirt got attached to the trailer in transit, they could easily clean the coach when it arrived at the dealer lot.

Use a stripper designed for aircraft use on aluminum. One such product is SV-35/AC or RemovAll 210, manufactured by Napier Environmental Technologies. It is easy to use – you just paint or spray it on and hose it off. It's classified as non-hazardous. One supplier is Aircraft Spruce. Napier also privately brands this product, and it is marketed by ICI Paints as Hydrostrip 502, and also under the Crown label. It's available in 1 and 5 gallon sizes.

Unfortunately no. The 2 part material is a special application process that is only being commercially done by the factory or: Airstream plans to build some regional service centers in the future that may be able to do this process too.

Answer: All the Carters have the same thickness on their cabinets as follows: the top deck is 3/4", the bottom deck is 1/2", and the front apron is 5/8".

Our products are not stained...color is the true wood. Older stock has a diluted watco finish, new product is dipped in Weiman LemonOil for Wood, does not clog pores of wood. The Accessory Bar is a Peg Bar, not intended for earrings, only necklace,bracelet, other larger open ended danglings, such as keyrings etc. Hi I am interested in a rack for necklaces -- one that hangs on the wall. The rack is for my daughter whose lease prohibits the drilling of any holes.

Oak wood has been used throughout history for it's water resistant properties, strength and beauty. For centuries, ships were constructed of oak wood. We apply spray painted stain to the oak wood in a variety of popular colors, and polyurethane clear coat.

The clear coat finish we use is Bulls Eye Shellac by Zinsser. It is an All-natural, non-toxic, very durable finish, works great to protect your prized quilt or wall hanging. UV resistant and non-yellowing, it is absolutely safe to use on children's toys. Currently we only offer the Clear finish, which has a faint, golden cast that is much lighter then other finishes. Please Note: Currently this is an added option not yet added to each item. Please Click here to add Clear Coat. Good Question.

Yes and no! You cannot clear coat over large graphics, but you can clear coat over small decals with thin lines, such as the P/T Cruiser decals and the motorcycle tank decals. Contact us for more details. Top

The clear topcoat protects both the surface of the wood and the tinted stain that has penetrated into the surface layers. The topcoat also has special UV inhibitors to stop the pigments in Pro-Tek-Tor from fading.

You shouldn't have to unless it gets scratched. But if you would like to re-clear coat the work anyway, we recommend using several light coats of a clear lacquer or polyurethane.

This varnish finish is presented in two jars, big and small, with varnish and hardener respectively. You have to mix two parts of varnish and one part of hardener. Caution! Once you have mixed varnish with hardener you CAN NOT put back the mix into any of the original jars! Surfaces that are going to be varnished must be clean and free of any dust or grease, this could cause bad effects in the finish. We recommend washing the model with water and soap before applying clear coat.

We recommend some practice before applying clear coat to any model. You should apply two or three wet coats with 10 minutes between them. You should airbrush with low pressure in slow movements, starting and finishing of throwing clear out of the model. It's important to keep the model in some place free of dust between coats and for the final drying time.

No. I use high quality decals which don't require a clear coat for protection and shine. A bonus of this is that when you get your frame and possibly not like your decal choice, you can change them.

The best way to determine a finish is through its damage. If a clear coat is in good condition it can be difficult for you to determine. Lacquer is the most common type of finish used commercially because it dries

Natural wood will always vary in color and grain. In nature, no two trees are exactly alike and neither are any two pieces of wood. These variations enhance the charm and unique characteristics of wood and should be appreciated as such. Yes, though to varying degrees depending on the type of wood and the climate in which you live. Wood shrinks or swells due to loss or gain of water, so changes in of temperature and relative humidity cause wood to expand or contract.

Clear-Flo? products have been used for lakes and ponds, industrial wastewater, aquaculture, landfill leachate, greenhouse irrigation water, agricultural waste, groundwater pollution and restaurant waste. Since many pollutants are ubiquitous, applications are numerous and ever expanding.

This will depend on the model number of your amplifier if you supply us with the model number we can tell you what materials are used to construct your amplifier.

Heritage uses solid oak trim as standard, and also builds and stains your custom oak cabinets right in our factory! Our state of the art cabinet and finishing system gives you a true custom built cabinet with the features you desire. Oak is our standard cabinet, but upgraded wood species such as knotty pine, hickory, rustic hickory; maple, and cherry are also available.

If the surface is clean, and will accept the Base Coat paint, you can use the Special Effects line of products. However, after allowing the paint to cure for three to seven days, you should protect the finished surface with a clear latex protector in your choice of sheens.

Clear-coating may provide additional protection for vinyl graphics, but caution should be used because solvents in some varnishes can attack the vinyl and/or adhesive, causing failure.

Everyone who wants the clearest vision possible from his/her eyeglasses, including children, especially if you spend time:

Yes! You can clear coat on top of any decals! You can also use our graphics as paint mask when you are applying paint to the vehicle. We would caution you to think about the consequences of clear coating before you do it though. Once you clear coat on top of the decal, it is permanently attached to the surface and yellows with age. Removing clear coated graphics will involve sanding off the clear coat and then removing the graphics, then a re-paint.

Yes. But be cautioned that Shingle Shield is designed specifically for use with three tab shingles. The installer assumes complete responsibility as to how to attach the product to a wood roof. The primary objective is to have rain water run over Shingle Shield, then onto the areas affected by fungus, moss, or algae.

Yes, but be aware of woods that have an inherent high level of natural oils, such as teak and kiaat. With milk paint being a water-based paint, there is an expected aversion to oil, including naturally oily woods and pre-treated timber.

Yes! In general, more coating is better than less. Parts subjected to harsh environments, such as direct UV light (sunlight) or aggressive aquatic or chemical exposure should be coated with a powder suitable for these environments. We will help you determine the right solution!