HTML reserves the & character for doing character escapes, so you need to use & to get the ampersand in your documents (and not just for HTMLDOC!)

We can't know for sure what characters will appear in Repercussions, but there are many theories. See the Castle theory thread to see some of these.

This will force the XSL transformation engine to output the text as is without escaping characters like &, which will result in the entire sequence &nbsp; in the html code and therefore your output can be shown correctly. You need to use the <xsl:output encoding=""> command in your XSL style sheet. Some transformation engines do not support specific encodings and it is therefore sometimes necessary to use another engine that supports the desired output encoding.

A Monox sensor, exposed to air and carbon monoxide only, cannot give a negative output (ignoring electronic noise which should be inconsequential). If your instrument is giving a negative value for the carbon monoxide concentrations, there are two possible reasons; i) There is an interference gas present in the gas sample which is capable of being chemically reduced by the sensor.

Many users who have converted from Acorn Comal have asked this one. When the Acorn Comal command 'VDU 2' is issued, output is sent BOTH to the screen AND to the printer. This doesn't happen with UniComal - SELECT OUTPUT only has one destination at a time, either screen, printer or file. This difference has caused a lot of head-scratching on all sides, and we still don't know of any way to echo printed output to the screen using simple UniComal commands.

This is one of my favorites. First rule: NEVER, NEVER go by the power ratings printed on an amp, or on the box. They are peak, or max power ratings. Translation: No way in hell! On name brand amps, check the spec sheet in the box, and look for the RMS, or continuous rating. This is what your amp is capable of on a regular basis.

Only if we know you personally. Even then, you can't be a face character unless we've met you in person. Web-only friends are limited to appearing as chat windows. Remember, the aspects of Omake Omatsuri that pertain to our social lives are based heavily on reality.

You can either drag and drop the character on the slide or you can specify its location on the screen. Locations can be specified as top, center, bottom, and left, center, or right, or as X and Y coordinates in relative values from 0 through 100.

Yes, download this taglib zipfile and extract the files into your Dreamweaver/Configuration/ThirdPartyTags directory. Dreamweaver will then show a little icon for output tags next time its started.

You are probably using EMMA's default output mode for offline instrumentation: copy. In this mode, <instr>/instr only outputs classes that got instrumented. So, a class that was not instrumented (for example, because it was not executable or because it was filtered out) will never show up in the output directory. When the instrumented classes are added to the start of the execution classpath, the uninstrumented classes "show through" in the original classpath.

ex.) like using 45 tubes in "Single ended: SV-2A3, -VT25Limited, etc." or "Push-Pull ended: SV-2A3PE, -300BMKII, etc."

Most of the time this is due to the lighting when photographing the jewelry. We work with many local designers & manufacturers in order to carry the selection that we have. As a result because of different finishes & techniques in creating the jewelry sometimes you may have some pieces that may be slightly lighter or darker in color but rest assured every piece is guaranteed to be 14kt gold except for items noted as platinum or silver.

This is a slightly unexpected effect of the option MULTIOS, which is set by default. Let's look more closely: foo 2>&1 >foo.out | bar What you're probably expecting is that the command foo sends its standard output to the pipe and so to the input of the command bar, while it sends its standard error to the file foo.out. What you actually see is that the output is going both to the pipe and into the file.

This section was written by someone who wishes to remain anonymous, but I will field any questions on the subject -IDB] Yes. When two loads are connected in parallel (such as with a Y-cable) they get the same voltage as each other. They do NOT get the same voltage as if only one load was connected because the head-unit has an internal resistance (typically around 600 ohms).

No: The output (or outlet) connectors in Cam-Lok's 200 Amp Posi-Lok series are "dead-front males", meaning a male contact with an insulated tip.

Coverage of NAPPA Gold Award-winning Children's Products appears in the November and/or December issues of more than 40 regional parenting publications (see NAPPA Editorial Partners) in top metro markets nationwide ? just in time for the gift-buying season. Both Gold and Honors winners enjoy front-and-center coverage on Parenthood.com beginning Nov. 1.

It seems that Acne affects the pilosebaceous units that are made of a sebaceous gland connected to a canal (the follicle), and a fine hair contained by the canal. The pilosebaceous units are found mostly on the face, neck and upper back. In teenagers a hormonal unbalance is produced during puberty and these hormones are stimulating the sebaceous glands to produce a lot of sebum.

When you make a post, you will have 2 minutes to edit your post without the Edited by line appearing. After 2 minutes the line will appear. {Also see above: Editing Posts} (If your post is edited by someone else--only moderators and admins can do this--the Edited by line will always appear. We don't always remember to put in a "reason for editing", however.) Last edited by Spherical Time : July 27, 2007 at 11:51 AM. Reason: to add mod edit note, format changes

The words “design and build” are terms used to assist the public to understand what a company can do for them. So in the instance of Moss Brothers Ltd it should be taken to mean that if you would like to build a character or replica home then our firm specialises in the total project.

GenePattern supports the Basic Latin character set. Characters other than those in the Basic Latin character set may not be displayed correctly. Asian character sets are not currently supported.

This is normal when the change will effect the way the character thumbnails will look in the game. This is to allow the game to generate new images that match their new look.

Shat-R-Shield clear coating reduces light (lumen) output by less than one percent (1%). -back to top-

This is actually documented elsewhere, but the documentation isn't very clear on this point (hard to understand), so I'll repeat it here. It goes into the bit bucket. Into /dev/null. Into the black void of outer space. Yes, the output gets thrown away and doesn't go anywhere. nographic mode is intended to be used for debugging OSes (mainly Linux kernels or Linux/GNU systems) which would run the system console on the serial port if they were running on real hardware.

There were a lot of characters (especially school children) who appeared on the show and then for some mysterious reason were never heard from again. A few key examples are Liam O'Neil (from season one) and Dr. LeDoux & Elmer Miles (from season eight). While their fates were never really explained on the show, we hope that the Little House Encyclopedia has done its best to fill in the gaps. The general term for characters appearing only once is "a one-shot appearance".

Just play with he (she) for at least 15 minutes. He (She) will be detected by our robot and added to database. Once added to database you don't need to play anymore! Your character will always be updated in our database after that. RookStat makes partial updates every 15 minutes. Partial means that online characters are updated only. If you uplevel and logout between robot scans your up will not be detected.

All HTML output is produced from an XSL transformation which uses the instructions contained within an XSL stylesheet and the data contained within an XML document. This has two points of great significance: If the XSL stylesheet tries to place a named piece of data in its output document, but cannot find a piece of data with that name in the XML document, it will not output anything for that data item.

Why does AMPL unexpectedly abort in the middle of doing something? I get a short error message, but I can't find it explained in the AMPL book or in the solver documentation.