No, it may be more expensive, dusty and dirty to jack hammer up the floor tiles but the Waterproofing Standards say that the waterproofing must go on the Substrate. By not removing the floor tiles you are relying on the existing tiles not to move and provide waterproofing. By removing the wall tiles and linings we can check the existing plumbing and re sheet walls so as to have a clean surface to water proof and adhere tiles to.

The DensShield panel should be positioned next to framing with the coated (grey) side facing away from the studs. Apply mortar or mastic and tile to the coated (grey) side of DensShield. The acrylic coating stops moisture penetration on the surface. DensShield Tile Backer is an entirely different product than greenboard. The paper facings of greenboard can wick water, and can delaminate when exposed to moisture, causing tile failure.

Yes, as long as the existing tiles are firm and secure and are able to support the weight of the new tiles.

Yes, this can be done and is being done more and more, as it is quicker and you have less disruption. You do however have to ensure that the old tiles are in the correct condition to be tiled on top of, wall or floor. The old tiles must be adhered correctly, not be hollow or have any cracks in them. (It is recommended to have a professional check them out.) You also have to use a special adhesive for the application, like Unibond, ask your sales assistant for more information.

No. The temperatures attained by floor heating systems are even lower than your floor may reach on a hot summer's day. It is however important to have your tiles installed professionally and according to manufacturers recommendations.

Yes you can fix tiles over existing tiling, but first you need to check that the existing tiling is firmly bonded to the background, then clean and degrease the tiles. Make sure a polymer enhanced adhesive is used.

Vitrified tiles are unglazed tiles. Their polish is achieved by very hard materials and they are very very strong and durable, whereas porcelano tiles are glazed tiles and their durability is as good as the durability of the glaze applied over them. And glaze are not hard and scratch resistant as the vitrified tiles.

Tile Installation over Cracks - I am building a house in Florida, and the slab is a year old, and its cracked. Before I install the ceramic tile, should I use any kind of underlayment to prevent the tile from cracking, and if yes, what kind? Can I use roof paper as an underlayment? I will appreciate your answer, thank you! Old Thin-set Removal - The first floor of my house is currently comprised of carpet in the living areas and tile in the kitchen and major hallways.

This is something you must decide. I can, however, explain why my clients have never complained. Most tile stores don't have the variety of designs that I offer with hand painted and decorative tiles. In addition, there is no direct contact with the artist. You must tell the salesperson what you want, and the salesperson must contact the artist. This takes time and often costs more. The big companies that have a lot of hand painted tiles, import most of the tiles.

Tiles made today are manufactured from new larger molds that do not match the dimension of the tiles that would be found on older Shaker homes. Tiles matching the old dimensions are still manufactured but are more expensive. The City wants to create a database of every property in Shaker Heights with a tile roof so a local distributor may order special runs of the old tiles at a more affordable price. Please contact Planning (216-491-1430) for further details.

International tile paints are suitable for use on glazed, ceramic wall tiles in kitchens and bathrooms. Although, we do not recommend their use around heat sources such as cookers. International One Coat Tile Paint with Teflon® surface protector needs no primer or undercoat and covers in just one coat. International's new One Coat Tile Paint with Teflon® surface protector provides a finish that is up to 3 times more durable & scratch resistant than the nearest competitor.

No, you do not need to use tile spacers to install the tiles. The chamfered edge provides an elegant look when installed "tile to tile". The 45-degree chamfered edge provides a natural caulking channel when the tiles are butted together. The XT-200 mastic allows sufficient time to adjust the spacing "by eye" for difficult areas. *Tile spacers can be used if you require large grout lines.

We have all seen how photographs reproduced in printed publications such as catalogues provide an image of an object (in our case a tile) which is faithful but not identical to the original, detailed but not necessarily complete. In other words, if we place a tile alongside a photograph and observe closely, we will see that the printed colour, although very similar, is perceptibly different.

Slate tile does need a little more in the way of maintenance compared to ceramic or porcelain tile, but its unique qualities and appearance are often preferred to man-made products.

Answer: No, James Hardie does not recommend this method of fixing. You may consider other methods of floor materials or compounds to raise the floor level.

Use Selleys UNIFIX. Selleys UNIFIX is a ready to use ceramic tile cement, it is quick to dry and suitable for use in areas subject to frequent wetting. Suitable for wall and floor tiles for bathrooms, showers, laundries and kitchens. Ideal for bonding tiles to any rigid surface such as plaster, cement, brick, stone and fibrous cement sheeting.

Selleys TILE BOND is an acrylic tile adhesive, white colour. Has excellent adhesion, quick grab, good water resistance. Ideal for bathroom walls, kitchen and laundry walls and floors. Recommended for bonding ceramic and mosaic tiles to concrete, cement render and fibrous cement sheeting. Selleys FIX N GROUT is a ready mixed acrylic adhesive and grout. It does not give off irritating solvent fumes.

No, we only make tiles. But we do recommend a very qualified group of tile setters who specialize in setting handmade tile. Please visit www.handmadetileassociation.org under resources

Yes, included with your Aquavee Swim System kit are 4 clear polycarbonate thin sheets and a tube of clear waterproof silicone adhesive. The Owners manual will instruct you in detail where and how to adhere the clear inserts in your pool. The inserts will not be apparent in your pool due to its transparent nature. Once installed (installation is a one time 5 minute process) the suction cups will attach to the clear inserts when you are ready to swim.

Companies that salvage and/or reclaim old roofing tiles are few and they are located throughout the country. Most of these will have a large variety of old roof tiles available and will also have a large database of smaller companies that have roof tile inventories. Through the search and match process more often than not, a roof tile match can be made.

No, they don’t break or chip easily. The tiles, which are manufactured in Ohio from local clay, are made of dense materials which can be fired at a very high temperature, making them very hard and durable. They have very low moisture absorption, which means they are excellent in a freeze-thaw climate and also resistant to mold and lichens.

Met-Tile is made of 3-ft-wide steel panels, in lengths of two to 20 feet. Since the panels are stepped to create a tile-like appearance, they are commonly referred to as "tile panels" or "tile facsimile panels."

Only non-endangered, certified, and finest-grade exterior woods are carefully selected. The plastic bases are UV-resistant composition of polypropylene and polyethylene. The screws are marine-grade gavenized stainless steel. Snapping Deck Tile : a do-it-yourself product designed for the average homeowners.

Our tiles are manufactured from 22 ga. stainless steel, which is .031" thick. They have a raised 1/8" face and an overall thickness of approximately 1/8". Our tiles with a Masonite backer have an overall thickness of 1/4".