You cannot connect directly to an IP using a phone line. There is a way, however, by using the internet. Connect to the internet through your ISP(cannot be AOL), then once connected you can start the client up and put in the IP address of your Watchdog. [FAQID No: 138]

There are several methods for computer connection, but it appears that Ethernet 10BaseT is emerging as the most predominant method. Although it probably would be cheaper to produce the cable modem as an internal card for the computer, this would require different printed-circuit cards for different kinds of computers, and additionally would make the demarcation between cable network and the subscriber's computer too fuzzy.

Yes you can! All you need is a Bluetooth adapter and Bluetooth mobile phone if not a mobile phone with a data cable. Once you have installed your mobile phone as a modem you then need to purchase a Movistar Internet Sim Card, this is a dedicated sim card for internet use only.

Where can I find hacks for Bolo? These and many other interesting issues are all addressed in detail within this FAQ. Once you've read the FAQ, feel free to post any other questions or comments relevant to Bolo. You may also post small binaries which are relevant to Bolo, likely to be of interest to a wide variety of people, and best distributed via Usenet.

You may have no signal or a weak signal. Make sure no obstruction is blocking the GPS antenna and that the Modem has a clear view of at least 3/4 of the sky. Make sure that you do not place your hand or another object over the GPS antenna. Determining GPS position can take up to 5 minutes. If your Modem cannot determine its position within 5 minutes, switch the Modem off and on again. The Modem may be configured to use an external GPS antenna.

Allways start with a complete power cycle or two and reboot the computer. Your computer might be broken, breaking, or glitching. Sometimes other people using your computer accidentally misconfigure it. You can check our "How to" section for instructions and try to set it up again if your a do-it-yourselfer. If you can't fix your computer, your more than welcome to bring it in to a repair shop. We have been doing computer repair for 13 years if you choose to bring it to us.

Check that the cable is connected between the modem and the telephone socket. There may be 2 ports for it to be connected to use the line port not the phone port. If necessary unplug it, then reconnect it. If you are connecting from your business telephone line you may need to dial a number to get an external line (usually 9).

Allows the user to use the same phone line for both voice and data (Internet), allowing them to receive an incoming call and allow the user to stay connected to the Internet for up to 8 minutes. (Call-waiting service from your phone company is required, optionally, having Caller ID and Call-waiting service, on your phone line, will allow the user to see the name and number of the caller). This feature requires a V.

A hub and switch are two devices that split the bandwidth coming from any ethernet device that is connected to them they will not route communications from your LAN to the internet. All they do is split the bandwidth so your modem can see all of the MAC addresses connected to it so it will only give a connection to one of those devices.

There are two independent composite outputs (Video, Audio Left, Audio Right) on the rear panel. Connect your TV to the output labeled "OUT 1 (TV)", and the VCR to the second output labeled "OUT 2 (VCR)".

Network of different IP schemes can be interconnected by using a airClient configured in Router or NAT mode for far end local networks. It is important to note that airClient in Router mode will perform routing and NOC or service provider is required to ensure the client network is recognized or routable.

Connecting to the DAXfs SMB service using the server's IP-address is not supported in the current version of DAXfs. Use the server's computer name (hostname) instead, e.g.: The KSMBD service does some basic security checking and it failed to identify the client system as a 'known' host. You will need to add the hostname and IP-address to the server's naming service, either the /etc/hosts file, NIS(+) or DNS. Adding the -n option to the KSMBD daemon or service will resolve this problem.

Network of different IP schemes can be interconnected by using a airHaul family of products by configuring a remote in Remote Router mode which allows to configure a different IP address scheme for wireless and wired network. airHaul in Remote Router mode will perform routing. It is important to note there is no NAT here and NOC or service provider is required to ensure the client network is recognized or routable.

Previously, we suggested that people use Mac modem cables; however, it has come to our attention that there is no one standard Mac modem cable. Since correct modem operation on a NeXT depends upon a correctly wired modem cable, buying a Mac cable is not a good idea. Some Mac cables do not allow dial-in and no Mac cable allows the use of hardware flow control. For these reasons, we are recommending that only cables that meet NeXT specifications be used.

The modem can be used on any PC or Laptop (that meets the minimum requirements) and it is portable. However the internet connection cannot be shared. The 3G Broadband Router will be more suitable for this use as the Internet connection can be shared.

ISDN, DSL, or Cable is preferred. Dial-up modems can be used as well but the images take considerably longer to come through.(depending on the phone lines in your area). [FAQID No: 143]

Voice Over IP over a quality broadband connection provides superb sound quality and excellent reliability. Usually better than old fashioned phone service. If you have more than 20 users at a single location it may be desirable to have an Internet connection dedicated to voice, and/or an Aptela premium dedicated connection. Your on-premise network will also play an important role in determining quality and reliability.

The DVR DCT6412 gets all the information it needs from your cable signal, so that's the only connection required.

Whether iVisit will work in this situation depends on the details of how your DSL "router" implements NAT (Network Address Translation, what allows machines in a private address space to communicate with machines outside the private address space).

Regional Bell Operating Companies are sometimes tariffed and will only allow (with perfect telephone line conditions) 53K. Tariffs are established by the FCC and by state Public Utility Commissions. Because analog lines are a little noisy (static), your modem will automatically slow down to accommodate for noise. It is normal for 56K modems to connect between 39 - 51K. This is still very good performance.

This is a common question because many things can cause this. First off, it is important to remember that while 56K is the theoretical limit a modem can connect on a normal analog phone line, NO modem ever connects at 56K. About the best a modem could ever achieve is 53K and a modem that connects at 40K or better in most cases is doing pretty well. Causes of slower connection speeds include: Unconditioned or poor quality phone lines.

First, the highest connection the FCC allows over standard phone lines is 53.3k. This is the fastest connect rate you can get. If your are connecting in the 40k-50k range, this is considered good for most dial up connections. If you connect at a rate less than you would like, your modems 56k protocol may not be compatible with ours. We support the fastest and most common protocols across most of our network, 56k Flex, v.90 and v.92. You can attempt to update your modem drivers.

The modem's USB connection is not supported by Windows 98. If you are using Windows 98 you will need to connect an ethernet card to your PC.

Yes, there are many manufacturers that offer broadband "routers" that are capable of allowing more than one computer to share a single internet connection and Windows 98, Windows ME, Windows 2000, and Windows XP all have an Internet connection sharing feature built in that can be used with your Suburban Broadband service. Your computers need to be connected to each other with category 5 cabling or a wireless networking (WiFi / 802.11) router.

Yes. Modest amount of remote dial-in access is available free of charge to members of the Whitman community through Whitman's pool of thirty-two 33.6kbps modems. To connect to modem, you must first request a remote access account via a web-based request form at https://secureserver.whitman.edu/dialin/. To ensure fair access to this limited resource, remote connections are limited to 4 hours per session and a maximum of 8 hours per day.

With the standard plan, you can only connect one computer to the modem. See the terms and conditions page for information and costs to setup a proxy server.

Check to see if the phone line is connected correctly to your system. Make sure it is connected to the LINE jack of the modem. Go into the Device Manager and remove all items listed under "Modems". To remove an item in Windows XP and Windows 2000, select the item, click the Action menu, choose Uninstall. To remove an item in Windows 98 and Windows ME, select the item and click Remove. If the installation asks you for the drivers point the installation to drivers.

Please check that your ISP supports 56K modems and that you are using the correct service. Using the wrong service will result in the modem not being able to connect above 33.6Kbps. The other possible reason is that your phone line is connected to an old PSTN (Public Switch Telephone Network) which is unable to handle 56K speeds.

If you connect a new device to the cable modem, such as a router or new computer, the modem must be reset. First, reset the modem by removing the power cord then plugging it back in, then reboot your computer or router.