A Before plugging your USB Flash drive in, download and unzip the drivers from http://www.ipsgproducts.com. Browse to C:\usbflash\USB Flash Disk 98 Driver and open USB Flash Disk Win98 Driver.exe. Once the installation has finished insert your flash drive into an available USB port on the computer. The flash drive will now be recognized and show up in My Computer.

A No. Only one partition will show up at a time. The secure partition will remain hidden until the password has been entered in the USB Flash Disk Utility. Once the password has been entered correctly only the secure partition will be active. To get back into the public area you must logout of the USB Flash Disk Utility.

A These items are available by going to http://www.ipsgproducts.com. On the right side, under products, click on USB storage and then select your flash drive.

A There are two ways. 1.) Open my computer, right click on the flash drive and choose Format. Choose your format options and click Start. 2.) Use the USB Flash Disk Utility. Open the USB Flash Disk Utility by clicking on Start > Programs (or All Programs) >USB Flash Disk Utility > USBDiskUtility. Click on the Partition tab and then click Partition.

A Open the USB Flash Disk Utility. Click on the Partition tab. Move the slider to the desired amount of public and private space and then click the Partition button. NOTE: When the partitioning has been completed, there will be a message (shown below) with the default password for the secure area.

All computers are equipped with multiple ports for inserting USB devices. Most workstations have a USB cable that is attached to the table for more convenient access to the ports.

Additional manufacturer's operating software (a.k.a. driver) is not needed for most Windows operating systems*. However, USB Flash Drives will not work with the Windows NT operating system because Windows NT does not support USB. The original retail package for each flash drive has the model number printed on the back of the insert card that contains your flash drive device type.

With your computer turned on, you plug your USB Flash Drive into a free USB port (often these are located in the back of your Windows PC or Macintosh). Once attached, your computer should recognize the drive as a new volume mounted on your machine. If for some reason your computer does not find your Flash Drive after it has been plugged in for the first time, a system reboot may be required in order for it to be recognized.

USB flash drives are using the USB protocol to interoperate with PCs (Macs too!) and devices with a USB port. Typically USB Flash Drives use mass storage class drivers that are incorporated in Windows Me, Windows 2000 and Windows XP or later as well as Mac OS 9 and Mac OS X or later as well as Linux 2.4.6 or later. Some manufacturers offer drivers for Windows 98 SE or Windows NT. Apple offers a mass storage class driver update for Mac OS 8.6.

Check the back of the USB drive packaging for three boxes. The box that is checked will be the required driver for a Win 98 system. The driver can also be determined by plugging the USB drive into a Win ME, 2000 or XP system and follow the below instructions: Then you will see: "Flash Drive SM_2.0 USB Device," use the "SM Driver" or "Flash Drive UT_USB20 USB Device," use the "UT Driver."

Encrypt the entire USB flash drive. However, you will not be able run TrueCrypt from the USB flash drive. Create a TrueCrypt file container on the USB flash drive (for information on how to do so, see the chapter Beginner's Tutorial, in the TrueCrypt User Guide).

If Windows 98 thinks there may be a problem with a device, it has a program called "Automatic Skip Driver Agent" that disables devices so that they can be bypassed when your computer starts up. If your USB Drive is not showing up under "My Computer" but is appearing under the "Device Manager" with this message: Windows stopped responding while attempting to start this device, and therefore will never attempt to this device again [Code 11.] For more information, look up ASD in Windows Help.

You must have Windows 98 Second Edition installed, or you need to have updated your installation of Windows 98 using the Windows Update website. You must also install the driver for your DiskGO? flash drive before you connect it to the computer. The DiskGO? flash drive device has a write-protect switch located on its side. Make sure that the switch is not in the "locked" position. If it is, use a ballpoint pen or small object to push the switch back to the "unlocked" position.

Last time I tested, Behold was still working under Windows 98. Over time, more incompatibilities will arise. It is unfortunate, but to fully support XP and Vista, poor old Windows 98 loses out. When off in the future, I finally add Unicode to Behold, that will probably spell the end of 98 support. But that's probably over a year away. If you don't upgrade to a new operating system by then, you're going to be having more problems than just worrying if Behold will run or not.

Don't expose your laptop to resonating noises, for example loud bass noise from speakers, heavy machinery.

A driver is required for systems with the Windows 98 SE (Second Edition) version installed (some elder versions of Windows 98 will not support USB devices). All newer versions of Windows (newer than Windows 98 SE) do not require a driver for USB flash devices. Windows NT (all Service Pack versions) will not support "Plug-n-Play" devices. Therefore USB flash drives will not work on such systems.

This is a conflict between some system BIOSes and the SanDisk Cruzer Micro flash drive. It is not related to the busTRACE software. If your system exhibits this problem, the system might appear to hang during Windows boot when you have our dongle (i.e. SanDisk Cruzer Micro) installed in a USB port. If you remove the dongle, the system continues to boot just fine. You can plug the dongle back in and everything works fine.

No. Windows NT does not and will not support USB. Therefore, USB Drive cannot be used under Windows NT. Please consult Microsoft for further advice.

The USB port supports connection to a single USB mass storage device. USB hubs to add more ports are not supported. For devices with multiple partitions, only the first partition is supported. Devices with secure partitions are not supported.

A A green icon means that you are viewing the public partition of the USB flash disk. A red icon means that you are viewing the private partition of the USB flash disk.

A The USB Flash Disk Utility can do this in Windows 98 and Windows ME only. To do this open the USB Flash Disk Utility and go to the Partition tab. Check the Bootable Disk checkbox, select your USB boot type, and then click the Partition button.

Most laptops now use lithium ion (LiIon) batteries. LiIons should be managed differently from the NiCad or NiMH batteries used in older laptops. In particular, LiIons should not be run all the way down to prevent "memory effect". First, they don't have a memory effect, and second, running them down tends to reduce their capacity. If the laptop does not need the battery it should be run to about 40% charge and stored in a cool place.

Right-click on the "Removable Disk" icon with the drive letter assigned to your Mobile Mini or Mini Flash Drive. Optional: Type in a name in "Volume label" if you have more than one USB Flash Drive and prefer to assign names to differentiate them. Click on "Start" button. A warning notice appears that all data will be erased. Click "OK" button.

WinXipher for USB Flash for short is USB version, it has exact the same application function with WinXipher. But the USB flash drive version support the USB pen drive, it brings more benefits for the users. Convenient: The user can bring it anywhere he goes, and it's convenient for usage. It's not rooted in any computer, user can use it upon plugged it into the computer. Secure: you can securely take you data with you anywhere.

The drive must support USB 2.0 and must be able to access data at 3.5 megabits per second for 4-kilobit random reads uniformly across the entire device, and at 2.5 mbps for 512-kilobit random writes uniformly across the device. As a practical matter, it's tough to find these specs for a flash drive before you buy it, so make sure that your vendor is reasonable about returns.

If your Mac is using Mac OS 9.0 or later, it should work perfectly okay with no drivers required. But if your Mac OS 10.2.8 and Under you may need to download a patch to get your USB drive to work properly. Mac OS 10.2 and Under user Do Not need this patch. Please follow the below steps: Double click "USBFlashDiskPatch10.2.x.mpkg" and enter password (If you have set it for your Mac before)