Yes it can be. We have a lot of experience converting Timber framed houses. We employ the services of a Structural Engineer who designs and certifies (with Professional Indemnity Insurance) wooden support structures to allow for a suspended Floor as well as supporting the roof trusses. To our knowledge we are unique in the Irish market with this approach.

This is a difficult comparison because of the obvious differences in the two types of construction. We believe that if you were to build conventionally to the same energy efficient levels and similar high quality custom interior finish, you would most likely pay more. At best we believe you would pay the same as a custom home and as little as 10% more than an average home.

Steel framing makes it easier to complete alterations. Just as steel framing allows for larger open spaces, the number of required interior load bearing partitions is also reduced, which enables alterations to be completed without affecting the integrity of the overall structure.

According to the Spider Myths page published by Roy Crawford at the Burke Museum , the number of hazardous spiders is "the number of spiders that pose even a mild hazard to humans is vanishingly small (perhaps 1/20 of 1% of all species)"

Yes. Members who eat and use the facilities at the house without living at the house are called "associate" members. Two different associate memberships are available: Associate members have full voting privileges at meeting and have full access to house facilities. If you are interested in becoming an associate member, please contact the membership coordinator at the email address listed above.

Yes, some owner-builders have opted to enclose the timber frame with conventional framing lumber in-filled with various insulation products. While this system is more labor intensive and time consuming it may offer a cost savings for the owner-builder.

A custom home designed by Timbercraft and completed by a qualified general contractor could cost as much as 20% more than a comparable conventionally framed home. Timbercraft does not have a catalog of standard models. We've found that it's much more productive to discuss with folks their own individual home building needs and desires. When you visit us in Port Townsend, you're welcome to review our portfolio featuring many of the custom homes we've completed over the years.

It certainly can, given the advantages of steel in terms of design quality, you might not want it to. There are no visible exterior differences between steel framed and traditional wood homes, both are finished with the same type of materials. However, the walls of a steel home will remain straight and true without warping. Steel also allows for more wide-open spaces because it can support longer spans.

Hang them as you would in a conventional home. Toggle bolts or hangers can be used directly on or in the drywall depending on the weight of the picture. Attach screws directly into the interior steel studs when hanging heavier objects. (Studs can be easily located using a magnet).

No. We follow our projects to the site and then make sure they are assembled with the highest quality and attention to detail possible. The very crafts people who complete your project in the shop are often the same people who complete the shell package on site.

We certainly can and we can do it economically! Our cathedral ceiling and decorative beams package provide the look and substance of a heavy timber rafter system without requiring the need for an expensive double-roof system. Of course, if a double roof system is a consideration; our structural beamed roof system is the real thing! Solid, milled Douglas Fir timbers serve as rafters, ridge and collar ties with 2' tongue and groove, V-notched decking above.

No, You do not have to convert your entire home, however you will need to have at least one appliance (i.e. water heater, stove, etc.) that requires natural gas in order to have your service connected. Additional appliances may be added or converted at your convenience at any time following connection.

To have a US item run under UK current you need to buy a transformer, a product that you plug into the wall and has a US-style jack at the other end. The transformer will "step down" in voltage from 240 to 120v. From there you may want to plug in a US-style power strip and provide current for sev eral products. Next you need to consider how many watts your transformer is providing (all transformers should clearly indicate this).

Yes it's sometimes possible however it has not yet proved to be easy. Common problems encountered include: Holding your temper whilst meeting with management committees to propose your plans and listening to their concerns about possible rerouting of flues etc. coming from other apartments. Access concerns regarding delivery of materials and removal of waste.

Where can I download a free C++ compiler? Updated! [Recently added the compilers.net site thanks to Dejan Milicic plus added Microsoft's command-line compiler (in 3/06). Click here to go to the next FAQ in the "chain" of recent changes.]

In the past many timber frame houses did not have insulation put into the internal panels which gave people the impression that this form of construction was noisy. Taylor Lane supply semi-rigid batt insulation to all panels for the client to fit between the studs. Tests have shown that a 90mm internal panel has the same sound reduction qualities as a single block internal wall.

When clay /straw walls are load-bearing with 2X4 Larsen trusses on 24'' centers, approximately the same amount of framing lumber is used as a stick frame house. However, none of the exterior plywood sheathing is required. In addition, keep in mind the expected longevity of an EcoNest? to be 200 years serving 4-6 generations.

Timber framed structures can be built on virtually any foundation configuration including full basement, grade beam, slab, and pier systems that may utilize poured concrete, concrete block or other acceptable foundation construction materials. Foundations are structurally engineered for each building site and specific construction details appear on all Timbercraft plans.

There are a number of options for running electrical wiring in houses enclosed with SIP's. A complete discussion of wiring options, along with installation diagrams, is included in the Construction Manual that accompanies your building package.

First and foremost, you need to find a plot of land! Allow plenty of time for this, as there is a lot to think about. Find out as much as you can about the plot in advance. Find out whether it is serviced, whether you will be able to get planning permission, what condition the ground is in for drainage, load bearing capacity etc. Check whether there is clear access to the site, whether there are overhead power lines or underground existing main services crossing the site.

No intensive cost exercises have been done on a comparison between a Timber Frame structure and a traditional brick and block structure. On a material only basis timber frame does work out more expensive on paper but there are many other aspects to take into account. bull; The speed of construction, whilst taking the bricklayers off the critical path and enabling trades to work both inside and outside the structure at the same time will give a speedier return on your investment.

For heavy items such as kitchen cupboards and bathroom fittings rows of timber noggins can be fixed into the timber frame panels at the required height before plaster boarding. It is widely known that the quality and strength of the fixing into timber is far stronger than if you were fixing into a modern day thermal block in traditional construction. Alternatively, certain internal walls that are required to take a lot of fittings could be lined with 18mm plywood or similar.

Conventional foundations are all that is required for our timber frame homes. In some cases we may require a specific detail.

Answer: The parking regulations of the zoning code require a two-car garage for every house. If you choose to convert and existing garage to living space, you will have to build a new two-car garage to replace the converted garage.

Getting framed" refers to having your documents displayed within someone else's frameset without your permission. This can happen accidentally (the frameset author forgot to use TARGET="_top" when linking to your document) or intentionally (the frameset author wanted to display your content with his/her own navigation or banner frames). To avoid "framing" other people's documents, you must add TARGET="_top" to all links that lead to documents outside your intended scope.

The title displayed is the title of the frameset document rather than the titles of any of the pages within frames. To change the title displayed, link to a new frameset document using TARGET="_top" (replacing the entire frameset).

No! The inside framing and exterior treatments would be exactly the same as with traditional wood framing. For example, sheet rock would cover the inside framing, and insulation and vinyl siding would cover the exterior. NexGen Structural Steel Panels can be incorporated with any standard roof construction. No. While the cost of lumber has been subject to wide fluctuations, the cost of steel has remained relatively stable over the past twenty years.

When clay /straw walls are load-bearing with 2X4 Larsen trusses on 24'' centers, approximately the same amount of framing lumber is used as a stick frame house. However, none of the exterior plywood sheathing is required. In addition, keep in mind the expected longevity of an EcoNest® to be 200 years serving 4-6 generations.