Sure. Just install TCP/IP (if you’re not using it already), set your IP addresses, and your all set to talk to your SIXTRAK stations. Most Ethernet networks can run multiple protocols (i.e. NetBEUI, IPX/SPX, TCP/IP, etc.) all at the same time.

Sure. Just install TCP/IP (if you’re not using it already), set your IP addresses, and your all set to talk to your EtherTRAK Ethernet I/O modules. Most Ethernet networks can run multiple protocols (i.e. NetBEUI, IPX/SPX, TCP/IP, etc.) all at the same time.

Sure. Just install TCP/IP (if you’re not using it already), set your IP addresses, and your all set to talk to your IPm unit over Ethernet. Most Ethernet networks can run multiple protocols (i.e. NetBEUI, IPX/SPX, TCP/IP, etc.) all at the same time.

Florian Xaver postet a list of intersting DOS network links to the FreeDOS mailing list: http://www.freedos.org/freedos/news/technote/157.html. Thanks a lot!

Yes, all you have to do is to obtain an IP address from your network administrator and follow the instructions in the installation guide.

Unfortunately DME32 does not have a function to communicate directly via either Cat5 or 10base/100base. However, DME32 can communicate via RS232C to PC.

The prestations are calculated and I have the plannings. I have the right selection on employees and date, but still not all the information is in the salary transfer: some codes are missing. I have finished the salary tranfer in Certo, but I still have to make a correction. Do I need to change the transferfile? Software: certo While reading out the clocks I get the error message: "No reply grom the communication-pc".

ReachBack is achieved by several different ways. You can connect the Ethernet port to the uplink, and have the BreadCrumb® DHCP and address from the uplink in automatic mode. You can also select bridge mode if you wish to extend the existing wired network over the wireless BreadCrumb® network, or you can select gateway mode to segment the BreadCrumb network from your uplink network.

From the drop-down box next to Data Encryption choose Disabled if the wireless network does not require security settings. If the wireless network requires security, choose the appropriate options for Network Authentication, Data Encryption, and then type in the encryption key into the Network key field. The Passphrase setting or any key generator that populates the encryption or network keys will not work with Dell wireless cards.

Yes, you can. Be advised that any switches or routers on an existing network must be configured to pass UDP messages. (Some switches and routers will not pass UDP messages by default.)

The Define Subnet window appears when you visit a LAN for the first time. This window lets you classify the subnet as either "trusted" or "untrusted." Once you have classified the subnet, the firewall will automatically recognize and apply the appropriate policies. The default option is not to trust the subnet so that other computers cannot connect to your computer. If you want others to connect to you, the firewall rules must allow incoming connections from that subnet.

PC/104 systems with multiple processors or peripherals that have Ethernet interfaces can use a PC/104 Ethernet switch or hub board to be networked together. Fast Ethernet and 10BaseT switches or hubs are available with auto-MDI-MDIX network installation and up to five auto-configurable 10/100 transceiver ports. Ethernet connections are made through either onboard RJ-45 jacks or via right-angle Molex connectors that can be used to mount RJ-45 jacks in a faceplate, endcap or enclosure.

Again no (though see earlier sections for other ways to share files between PCs and Acorn machines). Work is ongoing to add support for AUN to Linux, both over Ethernet and (when running on suitable hardware) native Econet, but there is no usable implementation yet. All Acorn computers since the Master have had their Econet station number stored in the first byte of CMOS RAM. If the battery goes flat, or you reset the CMOS RAM, it will get cleared to zero - this isn't a legal station number.

With the current adapters you cant, the USB modem is the DSL equivalent of a WinModem and requires some processor power to perform the modem functions and convert the ATM data into TCP/IP for presentation to the PC. There is a Draytek device however which can effetively act as a router and presents ethernet to the user side. See details here.

No. There is no FTP daemon running in the PBX. Nortel wants you to buy Meridian Administration Terminal or its successor, Optivity Telephony Manager, for this. If you connect the PBX to your Ethernet LAN, be sure to block broadcast messages from reaching the PBX by using a router. A router seems to be the only acceptable way to block those nasty broadcast messages that can take your PBX completely out of service. It sounds as if you are receiving traffic reports through your modem connection.

Very simply, a pigtail (a short jumper cable) is needed to connect the cAntenna to your wireless card and/or access point. Your wireless device needs to have detachable antennas for it to plug into. Many on the market now do so. We carry a complete line of pigtail cables. Because the cAntenna uses a standard N-Female connector, the cAntenna end will need to be a standard industry N-Male connector, to whichever connector your device uses.

There are two RJ45 ports at the back of the Bluetooth Access Point, LAN and Uplink (port with a X sign). If you are connecting via a router, please use a standard RJ45 ethernet cable and plug into the LAN port. If you are connecting directly from the ethernet jack on the wall, then you should use a standard RJ45 ethernet cable and plug into the Uplink port (or a crossover RJ45 ethernet cable and plug into the LAN port).

For wired connections users must fill out an IP address request form for each machine they want connected to the network. You will need to enter the hardware (MAC) address for the Ethernet card being used. We use DHCP to provide IP addresses for laptops, whether it is a wireless or wired connection. We will assign static IP addresses for desktop and server machines.

Morpheus will automatically connect to the network for you. Note that when you first launch the program, it may take moment for it to find suitable peers to connect to. Please be patient and allow Morpheus to connect to your peers. If using a firewall, make sure Morpheus has permission to access the internet.

Sure. Some companies use "Virtual Private Networking" software (VPN software) to let their employees connect to their internal systems and Web sites from outside the office. EarthLink Wi-Fi is generally compatible with VPN software. Contact your company's IT department to find out if this is available to you.

I sit in my chair in front of my computer and work, that’s what I do. I have a job and deadlines. I review what I did last time I worked, and polish it. I write odd little bits that people ask for – interviews via email, book jacket material, letters to my readers for the publisher, and so on. The Femme Fatale newsletter. Emails. And somehow, the pump gets primed, and I start working again.

We offer lessons on our boat or on yours. We also offer a discount for lessons taught on your boat. Please check out our different packages for more info.

Messaging Server fully supports the latest features and functions associated with SMTP/MIME-compliant messaging systems. As a result, Netscape Messaging Server connects seamlessly with any existing SMTP messaging system or any SMTP-compliant messaging gateway.

YES! You can perform what’s called an “Improvement Exchange”. The professional, qualified intermediary plays an important role in the structuring of this type of an exchange transaction. NO! You need to acquire a replacement property for at least the value that you disposed of in order to PAY NO TAX, and it has to be a property that you don’t already own.

Yes. SELECT customers may have up to four computers connected simultaneously. However, CLASSIC customers may only have one computer connected to the network at a time. Yes, with Choice OnLine you can surf the Net and simultaneously make phone calls or watch TV. To use a fax machine or dial-up modem while surfing the Net, you must have a normal phone line available. Your computer will not allow you to use our Choice OnLine service and dial-up to another Internet service simultaneously.

Yes the SQ2020 2F8, SQ2040 2F16 and the SQ2040 4F16 have inbuilt Ethernet connection. For the SQ2020 1F8 we supply a serial RS232, Ethernet converter kit (SQ20A801) a power adaptor lead is included with the kit to power the modem and the Squirrel from the mains power pack (MPU-12V)

Yes, our program can be networked right out of the box. Since the release of Shepherd's Staff 2007 all licenses are for unlimited use within the same church.

It uses a connection to the data LAN to enable the delivery of voice and fax messages to multimedia computers via desktop messaging and administration of the CallPilot system from any computer on the corporate LAN. This connection can also be used to provide VPIM networking.