The floor sink must be accessible for cleaning, but you should speak to your local plumbing inspector for height requirements above the finished floor to ensure it is installed in accordance with the Uniform Plumbing Code. Check with the Uniform Plumbing Code and your local building department for specific rules and regulations.

Absolutely, but measurements need to be taken to make sure they match each other. Please consult the local fabricator.

We would recommend that you select them before the fabricator processes the top although there are some universal models or sizes. Sure. The proposals we recommend are the ones most commonly adopted by the majority of fabricators. You may communicate your ideas to the local fabricator so they can design according to your requirements.

Tarkett FiberFloor may be installed using the Glueless or Full Spread Installation Systems. See the Tarkett FiberFloor Installation Manual for more information.

We recommend the F.G. 1000 floor cleaner, which is specially formulated to clean your Floorguard? floor system, without causing any damage or dulling.

We offer a glass tile that meets ANSI and ATSM standards for residential and commercial wall and floor applications. The artwork is infused on the underside of these tiles which protects against wear and abrasion. These tiles are recommended for floors, walls, and swimming pools, and have a textured surface.

Yes. However, tile will not bond directly to a wood floor. We recommend the following methods to prepare your wood floor for tile installation: Install Schluter Ditra, from Schluter Systems, with a latex thinset. Then install the tile using a non-latex thinset.

Though there are some common fixture sizes, we highly recommend choosing the sink and faucet before your custom countertop is created by a fabricator. A :Light colors show wear less than darker colors and require less maintenance. Any Meganite? color should provide many, many years of dependable service. A : For the highest gloss finishes, use a finer grit pad such as a white polishing compound with water and try to blend it with the rest of the countertop. Buff and dry with a smooth cloth.

Again, this depends on the timber products used, the coatings, and the weather, a indication is given below:

The sub-floor must be level to 3mm over 3mtrs. If not then either a leveling compound must be used, the floor sanded/ground to the required level or battens could be installed and packed and the plywood attached to them. Keep in mind that the last option would, of course, increase the height of the floor. The parquetry is then set out to ensuring that the pattern remains straight, and leaving a minimum 10mm gap for expansion around the perimeter.

For custom ordered products, it takes 2-4 weeks. First, we’ll measure and give you an estimate. Then, materials need to be ordered and delivered and then we’ll call to see how your schedule looks for installation.

Yes - as long as you have access to the sub-floor. STEP Warmfloor? can be installed between floor joist without altering your existing floors.

We follow the guidelines established by the National Wood Flooring Association (NWFA). The NWFA recommends floors are to located in the room wear they are to be installed in for a minimum of 14 days. It is important to separate the individual bundles from the pallet for proper acclimation. It should also be noted that you should refrain from using any material that would increase the relative moisture levels where the flooring is being installed. This would include painting and spackling.

Partition walls can be installed flush to the floor. This requires changing the standard hole layout on the posts; a simple modification, but best ordered from the factory. Gates and doors will always have at least a 1" gap between panel and floor.

It depends on the type of wood floor you choose. Our Engineered floors can be installed over existing floors such as ceramic tile, vinyl and most other types. Solid wood floors have some limitations in this area. Best to talk to your Wood Flooring International dealer about whether or not it’s a good idea to install the floor you want over the floor you have.

DuroDesign Bamboo floors are also available in an engineered plank measuring 7-3/8" x 5/8" x 72" which is ideally suited to a floating floor installation. No, we use only natural bamboo for our stained flooring. Carbonizing bamboo softens the product by approximately 30 %. Carbonized bamboo is darker in color because it has undergone a change, not a stain. During the manufacturing of the product, the strips of bamboo are boiled and change color (becoming browner in tone and softer).

DaVinci Slate and Shake can be installed following standard industry practices. No special training or handling is required for the contractor. Plus, because it is lightweight, DaVinci Slate eliminates the time and expense of reinforcing the roof structure that is otherwise required when using quarried slate, concrete or clay tiles.

The brown stain is from too much iron in your water. It is closely related to simple rust you see on metal, which is iron oxide. Probably the source of the water you use is ground water, and the water has filtered through rocks containing iron-rich minerals on the way to the well.

technology improves, companies are always coming out with a new heat sink or Fan that has the edge over the competition. Some of the most commonly used heat sinks among Overclockers included those made by Thermaltake, Swiftech, and Thermalright. Check out the Overclockers Club review section for reviews on various heat sinks to see what is right for you. If standard air cooling isn?t getting the job done, or has become too loud for you. There are a few more options that can help cool a hot CPU.

Yes they can! Just like any boat if there is a problem that brings on water. Click here for an incredible story of an Amphicar salvaged after 17 years under water! Not to worry! It is not common and these cars are very sea worthy in spite of the bad press they endured in the press early on.

We recommend that an unfinished hardwood floor be installed after the drywall is finished and the painter has sprayed on the primer coat, but before the trim carpenter has started the trim out.

Local construction practices for one-story housing units usually include the use of pure cement paste used as anchoring adhesive. It is also valid and even more resistant to use structural epoxy resin for special or more important applications. The height of anchoring bars specified in the technical manual is oriented toward the construction of one or two story housing units, allowing the required resistance and safety for that matter. Back to top

It's important that your floor be strong and without any flexibility. Your joists should be 2"x10" centered every 16". The plywood subfloor must be either 5/8" exterior grade plywood or 3/4" OSB before you begin adding to the substrate. Deflection both dead and live loads must not exceed L/360 for ceramic tile or L/720 for natural stone and some larger ceramic tiles. There are allowances made for variances to the above. Check with the pros in the forum for recommendations.

Ans) The best suggestion for this question is that you can paint after the new floor installation is completes. Some flooring can easily damage our painted walls. When we completes touching up then the painted area requires minal work.

The sub-floor must be made level to 3mm over 3mtrs, or the height of the battens packed so that the finished floor will be so. The flooring is attached to the battens with glue and nails, leaving a minimum 10mm gap for expansion around the perimeter.

The sub-floor must be level to 3mm over 3mtrs. If not then either a leveling compound must be used, the floor sanded/ground to the required level or battens could be installed and packed and the plywood attached to them. Keep in mind that the last option would, of course, increase the height of the floor. The flooring is attached to the plywood with glue and nails, leaving a minimum 10mm gap for expansion around the perimeter.