No. Films must be installed on glass only, or surface damage may result. If you install the film on any type of plastic (such as Lexan or Plexiglas) bubbles will form underneath the film.

Window film adhesive should not make contact with plastic, Plexiglas, acrylic, or lexan surfaces. The film's adhesive contains chemicals that could react with the organic base of a plastic surface to produce a milky, bubbly appearance. Your plastic surface will never be clear again. If, however, the appearance of the plastic is not important, film can certainly be applied. Suggestion: GILA brand removable-reusable static-cling vinyl is perfect for use on flat plastic surfaces.

We do not recommend this nor do we install film on it. However below is Llumar ? documentation regarding this question we are asked often which may be beneficial to you in answering the question you have been searching for: The answer is somewhat complex. Generally speaking, the simple and flat answer (as of January 2000) is "NO," though research is always on-going and new specialty products more compatible with plastic sheeting are always a future possibility.

No. Our products (most window films, for that matter) cannot be installed on Plexiglas, lexan, or acrylic windows (i.e.-skylights). Any type of glass window is acceptable.

Clear plastic surfaces such as windshields, bridge enclosures, dodgers, cockpit curtains and portholes are easily scratched and dulled, obscuring visibility. This problem is aggravated when the wrong cleaning products are used. To restore clarity to dull and scratched surfaces, it is essential to use a cleaner specially made for clear plastic surfaces.

Lexan XL10 is a polycarbonate plastic product produced by General Electric. It is virtually unbreakable and the same material that bullet-proof "glass" is made from. It offers the clarity of glass, transmitting up to 90% of visible light while filtering out harmful ultraviolet light.

First, your windows and frames are cleaned to remove all dirt and debris. Any paint or putty on the glass is carefully removed. 3M's patented adhesive is already on the film and is protected by a clear liner. The liner is removed and the exposed adhesive is lightly sprayed with a solution of baby shampoo and water to ease installation. No chemicals are used. The film is then squeegeed to the glass and trimmed, leaving a small 1/16" to 1/8" border around the frame.

Window films are designed exclusively for professional installation and sold only through licensed solar control window film dealers. This dedication to our nationwide network of dealers helps ensure the proper installation of your film.

A good quality Carbide Tipped Triple Chip saw blade is preferred when cutting Plexiglas. This reduces the amount of chipout on the opposite side of the material and produces a smooth edge. A Router can be used to cut Plexiglas as well. The Router should be at least 1.5 HP or better and with changeable collets for a 0.5" Shank quality 2 flute Carbide bit. This reduces the vibration and chattering when cutting and will produce a more smooth edge.

Check the protective paper covering for any rips, tears or folding at the time of purchase. In most cases if visual inspection is not done at the place of purchase, it's very difficult to prove product defects or damage done by the seller. Inspect all surfaces that will come into contact to reduce tearing and scratching of the protective paper covering and the Plexiglas finish. Make sure that the protective paper covering remains in place until all machining and milling tasks are finished.

Basically it is the best there is. It is clear, forms a consistent shape exceedingly well, and is basically bombproof. Well, maybe not bombproof, but Lexan is a polycarbonate used in bulletproof glass, and in other applications requiring great strength. Many ocean-going boats rely on Lexan for the windows and portlights, as it is capable of standing up to punishing ocean waves..

Although these are remarkable products that are being improved every year, they are no substitute for shutters. If you have windows that for some reason, such as access, can't be shuttered then you may wish to consider using the film or installing the shatter resistant glass. Remember that the film only protects the glass, and the frame is still under pressure and the whole window could fail.

M strongly recommends that Scotchgard™ Paint Protection Film be installed by a fully trained and certified, professional certified installer. These are skilled certified installers in applying the film around compound curves, challenging grillwork, wheel openings, bumpers and all other areas on today's vehicles.

We strongly recommend that Paint Protection Film be installed by a fully trained, professional applicator. Much skill is required to apply the film around compound curves, challenging grillwork, wheel openings, bumpers and all other areas on today's vehicles.

If you follow the instructions we provide in our videos, installing window tint is very easy for do-it-yourselfers. Most all of our residential and commercial films are tested and rated “dual pane safe.” The ones that are not, state "not recommended for dual-pane windows" in the description of the product. None of our automotive films are dual-pane safe, and should not be used on dual-pane windows.

Installing window film is one of the easiest do-it-yourself projects there is. All of our films are self adhesive and are applied with a simple mixture of water and baby shampoo (one teaspoon to a quart of water). There is no sticky residue, no messy clean-up and no extraordinary skill involved.

Basically, you will need tools to clean the glass, cut the film, squeegee the film and spray the soap and water solution. We offer basic and deluxe tool packages for both automotive and commercial / residential Common window washing solutions may be used to clean the films, along with a soft cotton rag such as an old T-shirt. Avoid any abrasive cleansers or towels.

Yes, our products are designed to be heated wrapped, whether it be in the microwave or in a conventional oven.

We have experience with this type of window, but its can be very tricky. You should have TC Window Repair conduct a FREE On-Site Inspection. Yes, the TC Window Repair process works on windows with internal shades or blinds. We need to exercise some caution when applying our restoration solutions. Please contact TC Window Repair for a FREE On-Site Inspection.

Film, need a "slippery" solution to make them easy to apply. It is extremely important that there are no ingredients in the solution that would lessen the life of the adhesive, causing what is commonly known as adhesive failure. This is the reason that film manufacturers no longer recommend dishwashing liquids to be used to apply these films. CPFilms has developed the ultimate application concentrate called Film-On.

Always on the inside. The film will stick to the outside, but it will greatly reduce the life of the film. This is due to the fact that the UV stabilizers are incorporated within the film's mounting adhesive, so the adhesive side must be facing the sun (installed on the inside, facing out).

Yes. As long as you follow established industry guidelines, you can safely install approved window film on double pane (thermal insulated) windows which are 40 square feet or less in size. For help and guidance in selecting a film for double pane windows, please visit our application guidelines page or read the list of The concern is that you can overheat any thermal (double pane) units that are exposed to the sun should you select a film that is not compatible with double pane glass.

Glass doesn’t handle watts, subs handle watts. Glass is as string or stronger than wood, and the joints are much stringer. No 12X12X12 is 1 cubic foot but with 1” thick walls the box internal dimensions are only 10X10X10. You have to take into account that the material itself takes up room

Plexiglas bubble skylights are light, efficient, and inexpensive. They are particularly well-suited to flat roof installations since they shed water so well and gather light from many angles. Their light weight makes them easy to get up on the roof. Often the bubble shape allows for increased head room. They are quite modern in appearance and may not be suitable in certain architectural environments.