We do offer "certain styles of pre-primed balusters" but we do not do any painting or staining of any kind.

We carry in stock a full line of Red Oak, Hard Maple, Mahogany, Cherry & paint grade systems. (Oak is our leading species & our most economically prived for stain grade material.)

No Main Deck Railings will last as long if you don't paint them however, the open cells will hold more dirt and moisture and require frequent cleaning.

The available historical evidence shows that Eichler used stains, not paint, on his homes, inside and out. One can speculate that, at least for the vertical-grooved siding, stains were employed so that the grooves stayed crisp and clean (the edges weren't softened by the paint), and some of the grain of the wood showed through (redwood siding was used throughout the 1950s). It is also possible that Eichler used stains because labor and materials costs were lower than for paint.

Jennings joinery prefers to paint or stain prior to glazing and assembly to properly seal the product. Also when using 6.38 Laminated glass (which is thicker than normal glass), if the inside rebate is not painted or stained prior to glazing then after the product is glazed the unsealed surface behind the glass edge is visible and un protected. Also after the bi-folds have been installed it is very difficult to coat the top and bottom of the doors to seal then correctly.

For specific questions on paints, stains and coatings the CSSB recommends contacting your local, Approved Installer or local, competent, professional paint contractor or paint store. The CSSB does offer some basic information on this topic, listed in its Exterior and Interior Wall Manual.

You should finish your stair as soon as possible after installation. The wood is finally sanded by our installers. Failure to finish the wood within three days could void the material warranty.

A primer coat is first applied using a 'high throw' electrophoretic anodic paint process. This allows the water based primer coat to penetrate all the way up behind the fins increasing protection to an area which is vulnerable to rusting with conventional methods. A top coat of polyester powder paint is then added to create an attractive, durable and easy to clean finish.

Although it is possible to use a different product on the rails, we recommend using the same product. This will make it less confusing when it is time to do maintenance. Rubbol Siding Finish, Rubbol Solid Stain, or Rubbol DEK may be chosen to more closely match the rest of the house.

Ans: The insulating additive will help keep the deck cooler while providing a slightly slip resistant surface.

Quite frankly, we don't know and don't care. Both are effective. It really depends on what type of look you are trying to get from you shed. Plus, we are carpenters, not painters. Call a painter to get his opinion on which are better.

We recommend painting or staining after assembly. The rungs of the ladders sometimes are a tight fit and the finish may get marked up during assembly. Also, the wood glue used in the notched legs adheres better to unfinished wood. It is also much easier to paint or stain it when it is set up as opposed to all the individual pieces on the floor. If you paint it, we recommend you put a good primer coat, and two finish coats of a durable enamel paint.

One of the benefits of vinyl windows is never needing to strip, paint or stain them. Painting your vinyl windows can void your warranty.

Ultimately the decision is yours. We believe all wood should be stained because it seals better & enhances its beauty. Stain is an upgrade and does cost more. If your decor supports a natural finish, we will be happy to accommodate you.

No, staining is translucent and will appear marbled or old aged. Paint is generally more uniform and will peel.

The objective in applying a stain is usually to change the colour of the surface (typically bare wood) without hiding the texture of the material. Some stains, called semi-transparent stains, allow the grain pattern of the wood to be seen. With paint, we create a new appearance, which may be flat, satiny, or glossy, and the texture and grain of the surface is obscured. Stains are typically thinner than paints.

There are unlimited choices for paint and stain colors. We do provide you a selection of colors, but if you have a specific color you'd like for your shutters, we can match it to a sample provided by the customer.

Yes. We stain and paint outdoor decks and patios. We also offer a power washing service for cleanup of decks, patios, and other exterior surfaces.

We recommend applying a protective finish to the fence once it is installed. This helps minimize the effects of weathering and maximize the life span of your fence.

Touch-up paint or stain is available for many of our styles. For ordering information, please contact the store where you purchased your furniture.

All of our paint and stain finishes are custom matched to the sample provided to us by the homeowner, for no extra charge.

Most clients prefer to stain the house. These are available in many shades and hues and are available widely. There are UV repellant brands which make it possible to prevent fading over time. However should you decide to use paint any oil based paint is satisfactory.

Yes, BST stain penetrates the surface of the material it is applied to. While a paint product adheres to the outer surface. BST stain sinks into the substrate and bonds below the surface.

You should certainly protect your deck from unnecessary moisture intrusion and the harmful effects of the sun's ultra-violet rays. Use of a penetrating stain, containing water repellant ingredients in most cases will protect your deck best. The pigment in the stain will absorb the ultra-violet rays from the sun and protect the wood fibers from degradation. In most cases a stain will need maintenance every 2-4 years while clear sealers require maintenance every 1-2 years.

All products make from timber must be stained or painted to ensure the good looks of the cubby and to reduce splitting and to seal the timber against weathering. We highly recommend staining or painting while the cubby is still in panel form and not assembled. It is easier to paint the pieces when flat on the ground.

It is very difficult to answer this question as it depends on the weather conditions and if the cubby is in full or partial sun, but generally when the original painting or staining has begun to deteriorate or look dry. We Recommend Quality Cubby Cedar Coating Stain which is available from our store. Read the instructions before you start and use the level to make sure the floor is level before you start to install the walls.

The paint finishes used on our panels are the highest quality. We start out with a high-tensile steel. We then coat it with a Galvalume 55% zinc, 45% aluminum coating. They are next pre-treated with primer, and then finally coated with a high quality baked-on enamel paint system.

Many shops are using automotive finishes today, mainly because they are chemically activated and require less time in an unstable state. For the average restorer, the equipment required to apply these paints and the experience necessary, isn't worth the investment or training. Many suppliers will not sell to the general public because of these factors. It is even questionable whether this approach to painting is acceptable. To many interested in authenticity, it is not.

Yes. Paint will adhere to a zinc finish. The use of zinc as a base or primer coating for painting is very common. The protective value of the combined finishes