Both the INFRA-M and INFRA-M2 processors use the Bag End MPS-120 external power supply unit. This may be purchased from any Bag End authorized dealer. In the event that the MPS-120 is practically unobtainable, an equivalent power supply unit may be used. The INFRA-M and INFRA-M2 will operate on an input voltage between 10.5 and 18.5 VDC with a required current of 100 mA. A miniature DC 2.5 mm connector wired with the center pin positive (+) should be used to connect to the processor.

No. The crossover point cannot be changed since it depends on the resonant point of the INFRA subwoofer system. The INFRA processors allow altering the hi pass filter frequency by changing plug-in resistors inside the units of the INFRA-M and INFRA-M2. However, this does not change the true crossover point of the system and will, in fact, create either a gap or an overlap in the frequency response of the bi-amplified system depending on the filter frequency chosen.

It is not possible to replace just the Acess Point power supply, the entire AP must be returned for replacement.

There are several places that sell replacement power supplies, such as Alltech Electronics and other replacement parts stores. [See section 10.2 for addresses, etc of these vendors] If you don't mind having the power supply not inside your Apple II, Stephen Buggie takes power supplies designed for IBM PCs, and fits them with plugs for either GS or ][, ][+, or //e. These sit outside your Apple II (which helps reduce heat inside the case), and are reported to work quite well.

We have extensive experience with power supplies and your unit will always be shipped with the correct supply. If we are unsure, and have never sent a unit to your country we may write to you before shipping for further information. We have shipped to over 50 countries throughout the world including the UK, the US, Canada, Australia, France, Germany, and many others so you can be sure our unit will work in your power sockets.

Ensuring your Power Supply Unit (PSU) provides enough power to your system is paramount to a smooth running system. If your PSU is inadequate you will experience degraded system performance.....or perhaps your PC or a single component will not run at all.... Based upon my minimum requirements posted above, you can see that my +3.3V is average, +5V is above specs, and +12V is a bit below specs....it all comes down to how many Amps you have left over.

Drop in at one of our offices and customer service will help you in ending your service with us. You need to give us the desired termination date.

No, the 810 and 820 series meters operate in using a "single ended supply" meaning you only need between 9 and 25 VDC to operate them. We sell very reasonably priced power supplies that accomplish this in a very economical manner.

A Sealed units should always be handled with care. If a unit is broken during installation we will be happy to supply a replacement. Please email your requirements and we will provide a price. Payment at time of order will be required.

Complete an APPLICATION FOR DRIVER LICENSE (DSMV 450) and submit along with a fee of $10.00 and positive proof of identification (see below). Appear at the DMV, Concord, or any substation. original or certified copy of his/her birth certificate, valid US Passport or Military ID and one of the following: Valid School ID w/photo Please Note: If your name is different than what is listed on your birth certificate, you must also provide the legal document of that name change (i.e.

Yes. Contact us and we will send you a replacement manual at no charge or download it in the User Manual page.

The Neutrik Speakon NL4MP connector is a keyed, high current, four conductor device which allows both the high and low frequency signals for a bi-amped loudspeaker system to run through the same 4-conductor cable. Bag End uses pin 1+ and pin 1- for connection to subwoofers. Pin 2+ and pin 2- are used for mid/high loudspeakers. All four conductors on both Speakon connectors are wired in parallel, but only two conductors are connected to the driver(s) in the enclosure.

There are two INFRA processors to choose from: the INFRA-M and the INFRA-M2. The INFRA-M is designed for stereo 2-way operation with a mono sum INFRA low frequency output. It has balanced XLR inputs, unbalanced XLR outputs and operates down to 18 Hz. It provides rotary controls for the INFRA low frequency output level and Dynamic Filter threshold level. It is designed for musical instrument systems, theaters and cinemas, recording studios, and home theater/stereo systems.

We're the same PAiA and we've been in continuous operation since even before our incorporation and introduction of first commercial products in 1967. In fact, as early as 1959 PAiA Electronics existed as a father-son partnership for the purposes of research and development (and expensing an electronics hobby for tax purposes). Our first commercial product was a circuit board that accompanied the "Cyclops Intrusion Detector" which appeared in the June 1967 Issue of Popular Electronics.

High End power cords are expensive and should be selected based on personal preference, specific electrical conditions in your area, etc. We do not believe that it is fair to force our clients to pay for a very expensive cable that we choose for them. We could definitely write a long paper about the relevance, irrelevance, use and misuse of technical data.

All units submitted for duplication must be free of glue, tape and adhesive residue; the pieces must be shampooed clean, and completely dry.

Using the "Bass Management System" on your surround processor, set the front Left and Right speakers to "large" (full range). Connect the Left and Right outputs on the processor to the Left and Right inputs on the Bag End Infrasub-18, respectively. Now, connect the Left and Right hi pass outputs on the Bag End Infrasub-18 to the Left and Right inputs on your amplifier (which powers the front Left and Right speakers), respectively.

Determine the extent of the damage and what caused it. Locate the model number and serial number on the jackplate of the unit. Call Bag End Service Manager at (847) 382-4550. You will be issued a Return Authorization number and instructed on packaging and shipment to our Service Department. Please include a copy of your receipt and any additional information about repairing the product when shipping.

The K3 DC voltage required is 13.8 V nominal/recommended; 11 V recommended minimum; transmit disabled below 10 V; system shutdown below 9.0 V. The K3 is portable, thus it's designed for operation with a 12-V vehicle battery or gel-cell. Estimated minimum current draw with no enabled options is 0.9 A on receive, 3 A at 10-W and 20 A at 100-W. These figures will be refined after further testing. On all HF bands, TX with a 12.0-V supply still allows 100 W+ output.

There are a couple of reasons why the power supply is important. Low voltage can reduce the motor power and the speed. High voltage can cause the motor to overheat. The frequency must be correct (50 Hz, 60 Hz, DC) for the pump to run correctly.

The main purpose of your power supply is to run your trains. To run your train your power supply must supply energy for your locomotive, smoke unit, sound system , and any lighted cars. You may also need power for accessories like switches, street lights, building and house lighting or any other accessories. Your TOTAL POWER REQUIREMENTS depends upon the number of locomotives or motors, and ALL OTHER items that require electricity. The length of the track is not a factor.

A 'Power Supply' converts the high voltage industrial or household mains electricity supply into a safe low voltage power source suitable for use with electronic equipment.

To request a replacement Member card, please call toll-free 800-242-NMAI (6624) or send us an email message to NMAImember@si.edu. If you are visiting the NMAI on the National Mall in Washington, D.C., you may also stop by the Welcome Desk located just inside our main entrance.

Certainly! You can check out a lender case to use while your bag is in for repairs. As our turnaround time is so quick for repairs, it’s best to let request a lender case before sending your case in, unless your case is unusable anyway. Round trip shipping will be charged to your credit card and we will include your prepaid return label with the lender case. Simply affix the return label to the original box and return the case within two weeks of receipt of your repaired case.

In our experience farmers are ingenious whilst frames are costly, especially if you need several. Therefore, we don't supply frames; we have seen various simple and cost effective methods of holding bags up and open from a pair of cup hooks to an upturned sheep hurdle.

Most likely yes, as long as the housing is not tapered. Our replacement filters are designed to be universal and to fit most other point-of-use and whole-house filter housings on the market. If in doubt, email a photo of your existing filter together with its physical measurements (diameter and length) to us and we will confirm for you.

The microphone for the RA 27, RE 14 and RE 27 is not a serviceable item. Although delicate and very accurate it is quite affordable to replace in the event yours is broken or missing. Just contact the Parts Department and tell them you wish to order a replacement analyzer microphone, (a k a MIC 1; no fancy part number needed here.)