Can we do our own installation?
Fact Sheets : PCCIE: Frequently Asked Questions (FAQ) : PCCI...The customer may perform installation with start-up accomplished by the contractor to ensure installation was properly accomplished.
Related QuestionsWhat is the installation time?
Frequently Asked Questions (FAQ)Typical installation takes less than an hour. Only two wires need to be connected and routed. Mounting on the instrument panel is accomplished with a Velcro® hook and loop fastener. Routing of the two wires must consider possible sources of abrasion. Good aircraft electrical wiring practices must be followed.
Related QuestionsWhat are the installation requirements?
Met-Tile Frequently Asked QuestionsA minimum roof slope of 2-in-12 is recommended, though lower slopes are acceptable if the side laps are caulked. Met-Tile may be installed over existing shingles or decking, and may also be applied over open steel purlins or wood rafters.
Related QuestionsIs installation difficult?
Skutt Kilns Frequently Asked QuestionsNo. You drill the few holes needed for your kiln, place the EnviroVent 2 spring loaded plenum cup under your kiln and mount the motor to the wall. We supply the aluminum drier ducting that is used between the plenum cup and the motor. Skutt even supplies the stainless sleeve that is needed to pass through the wall. It runs on 115V household current. If you install the EnviroVent on a kiln with a metal floor plate, you will need an electric drill.
Related QuestionsWhat is involved in the installation?
Phoenix Internet Wireless Faq's - Wireless FAQsWe install a small antenna on or near the roof of your home or business. Then a Cat5 cable is run down and into your home.
Related QuestionsCan I do the installation myself?
ACCESSORIES R US Service 1Most of our customers do their own installations. All of the products we offer arrive to you with complete installation instructions. Our website also has general guidelines for installation. Please refer to the instructions included with your kit, as installation instructions.
Related QuestionsQuadrex Corporation, High Purity - High Output Gas Generator...Installation is easy ? simply connect the Generator to your electrical supply and an external water source. The Generator will automatically pump water into the holding chamber, then, after a 4 minute "System Check", the Generator will automatically begin producing ultra-high purity gas. Pressure can be regulated at the rear of the instrument.Related Questions
Farm Signs FAQ-Canada-USAWe would be glad to make some recommendations for the installation of your sign. We have measured drawings available to assist you in fabricating your own posts, or we can design alternatives for your unique situation.Related Questions
FAQs about Advanced Transportation Management Systems and In...We do minor installation and assembly in our facility. We are not a contractor and do not install equipment, provide field service, field trouble shooting or field installation. If you are in the Pacific Northwest we can recommend providers to you.Related Questions
Can I have someone else do the installation?
Frequency Asked QuestionsYes- most local avionics shops or TV repair shops will install the units for a fee. Or, you can send the headset to us and we will professionally install the ANR kit, bench test the headset to see that it functions correctly, and give you a three-year warranty on parts and labor. Please send the headset in with all accessories (ear seals, cords, cables, adapters, etc.) so that we can bench test the headset after we have installed the ANR kit. For our shipping address, please contact us.
Related QuestionsFrequently Asked QuestionsNo, we are not installation contractors. However, we work closely with a installation company, Net-Services, they can be reached toll free at 888.365.6387 or their website is http://net-services.usRelated Questions
Stevenson Stained Glass : Custom made door and window staine...Final delivery and installation is your responsibility. Most often a van or truck is sufficient for transporting and a trim carpenter or handyman can set your piece in place and trim it in. We can offer you names from the Asheville area. Installation is easy - a handy man or woman can hang these over existing windows or fit and trim them in.Related Questions
What to do before installation?
Euro Pratik Sales Corporation - CANFOR :::Hardboard panels should be placed around the room where they will be installed on their long edges (backs facing out), and left for 48 hours to acclimatize the humidity level in the room. If the humidity is very high, acclimatize for 72 hours. This must be done by everyone including contractors. This is a wood based product and will expand or contract depending on the moisture level in the room.
Related QuestionsF.A.Q.The installation needs to be performed by one of our trained certified technicians. Â We do train our dealers that sell larger quantities. Â But even some of those have us do it anyways. We get this one all the time. Â Some manufacturers say in their manual that your warranty is void if you do this. Â Some donâ??t say anything about this mounting position. Â What we can say is that we have never had a plasma screen die on one of our lifts.Related Questions
Who pays for the equipment and/or installation?
Fact Sheets : PCCIE: Frequently Asked Questions (FAQ) : PCCI...Replacement UPS equipment and its installation is budgeted for by our office, provided sufficient lead time for replacement is available (typically 2 years). If the need date is sooner than 2 years, the customer is usually required to fund the requirement. The customer must also budget for ancillary equipment (new or replacement) required to support the UPS, i.e., generators, switchgear, HVAC, etc. For new missions, the customer is also required to fund the requirement.
Related QuestionsIf we do our own installation, how will it affect the warranty?
Fact Sheets : PCCIE: Frequently Asked Questions (FAQ) : PCCI...Warranty provisions vary; however, if the contractor performs start-up after user installation, the warranty is typically not affected/degraded.
Related QuestionsWhat if we have a problem with the unit after installation?
Fact Sheets : PCCIE: Frequently Asked Questions (FAQ) : PCCI...Our office should be contacted as well as the manufacturer. The method used for returning the UPS to a proper operating condition will depend on the elapsed time after installation, and the nature and cause of the problem. In any case, our office will work with you to ensure the UPS is fixed satisfactorily.
Related QuestionsDo I have to purchase installation?
ImageFolio 4.0 Professional Edition Frequently Asked Questio...If you have knowledge of installing Perl scripts and are familiar with FTP, don't order installation. The installation is very simple. If you don't have knowledge of Perl and FTP, you should definitely pay for installation.
Related Questions