No, all concrete slabs shall have six inches by six inches wire mesh for reinforcing with four inches of concrete and four inches of compacted gravel or sand. Exception: Basement floors are not required to have wire mesh.

Although the vast majority of our buildings are constructed on our superior floor system and sufficient for any application, we do have the ability to construct your Heartland building on an existing slab provided the slab is level within ?" and appropriately sized. Because of the individual nature of each slab, please contact us to determine if your slab meets our specifications.

Mohawk Engineered & Longstrip (glueless) Hardwood Floors can be installed over most concrete slabs (not solid hardwood). The concrete slab must be fully cured for at least 60 days, free of structural defects, clean and visually dry with no history of moisture problems. When testing for moisture, Mohawk suggests utilizing the industry-standard calcium chloride test or the Tramex Moisture Encounter (5 max).

Any reputable installer will insist you consider getting a moisture test done if your slab is less than six months old. If the moisture content in the slab is higher than 3% the installer may suggest the use of a moisture barrier to protect the timber flooring while the slab continues to dry.

Not necessarily. However, it is simply a matter of what the purchaser wants. The building will be built on pressure treated skids and they will sit on top of the concrete. The most important thing is to ensure the site is level prior to L'il Barn Builder constructing your building.

Yes. You will need to make your sales representative aware of this, so the materials can be figured properly. Anchor bolts will need to be placed in the slab on 3' centers prior to construction. Ask your sales representative for an anchor bolt layout; this will need to be used when the concrete is poured. Back to Top

Trusteel is not a concreting business however we can arrange for a concrete slab to be laid or you can engage a local concreter to undertake this work. Until a site visit has been undertaken, the concrete price quoted is a "budget price". The finalised price will be based on a 100mm (unless otherwise stated) thick, reinforced concrete slab with allowances made for any fall that may require filling on site or access restrictions.

You can install StoneDeck over a concrete slab but it would be more cost-effective for you to use a stone without our system’s special composite backing.

While modified asphalt provides the primary waterproofing characteristics of these membranes a reinforcing ply adds strength and puncture resistance. Glass fiber and polyester plies are the most commonly used reinforcing fabrics. Each has distinctive properties. Polyester has excellent elongation, tensile strength and recovery. It provides good puncture resistance and stands up well to foot traffic.

If the question is can a 3/4" hardwood floor be installed directly on concrete, the answer is "I wouldn't if I were you". If the question is can a 3/4" hardwood floor be installed over top of a concrete slab, the answer is "Yes". Our showroom is a perfect example of that. Can you nail hardwood into concrete? No.

Concrete hardens as a result of hydration, that is the chemical reaction between cement and water. Hydration occurs only if water is available and if the concrete's temperature stays within a suitable range. After placing concrete, the concrete surface needs to be kept moist for a period of time to permit the hydration process. this period is referred to as the curing period and is usually 5-7 days after placing conventional concrete.

It can read the moisture as a relative reading; in other words it will give an indication of a problem area, but will not give a definite moisture content. There are constituents in concrete that can cause the moisture readings to be in error, but as long as the concrete is homogeneous, the error will be constant. Example: If the slab reads approximately 12% moisture in all areas but one area is approx. 20%, it can be assumed that this is a problem area.

When considering the FRL upgrade of Concrete elements thorough investigation is required and some of the salient points are:

With the improvements in hardwood floors most engineered and longstrip engineered plank floors can be used over a concrete slab. Manufacturers do not recommend using solid wood floors over a slab. Engineered planks and strip wood floors can be glued directly to a clean, dry, well-cured concrete slab. Some engineered wood floors can be glued at the tongue and grooves and then allowed to be floated over a special padding that is laid over the concrete slab.

A - The slab may be of any size sufficient to stop the bottom of the mast pushing down into the ground but a standard paving slab (as opposed to just a paving stone) of about a foot square and two inches thick would be more than adequate for most situations. A piece of ground treated, solid, timber would do just as well.

Screw Clips twist into the foam-board insulation. The tubing snaps into the screw clips. Then, wire mesh (remesh) and/or rebar is laid over the tubing. When you pour the concrete, pull the wire mesh to the middle of the slab. Be careful not to pull the tubing up with the remesh when you pour. Many people prefer to use fiber-reinforced concrete so they don't have to install wire mesh.

Basement-foundation plans are included with all houses. However, we dimension the foundations in such a way that they can still be used with slab or crawl spaces with very minor changes for your contractor, or slab and crawl-space foundation plans may be added to blueprint and mylar orders for an additional $50.

Yes, you can install solid wood boards on a concrete slab. As 3/4'' boards must be nailed and not glued, you must first install a wood subfloor (plywood or OSB panels).

The bonding surface offered by the concrete should not be overlooked. The surface should be unpainted without contamination from compounds such as formwork releasing agents, oils, grease, etc which may impede the proper adhesion of the Vermitex 'AF'.

It is not recommended to install solid wood flooring over a concrete slab. Although this is the general rule, there have been successful installations of solid wood flooring installed over dry, concrete slabs. This entails several additional steps. A plastic barrier is set over the slab and taped at all seams. Then some sort of moisture-resistant wood subfloor (marine plywood) is built on top of the plastic film. Then the flooring is nailed to the wood subfloor.

Yes. National Barn Company uses a 2 x 6 CCA treated bottom plate around the bottom of the building. This board can be used as a form for pouring a concrete slab. Concrete can normally be poured through the large door opening. If the concrete contractor requires additional access to pour the concrete then some wall metal could be left off and installed by the customer after the concrete is poured.

Maybe. Most of our divisions can coordinate the concrete for your building, but this is typically limited to 150 mile radius of their office. Ask a sales representative for specific information. Back to Top

Yes, this is often done. Actually, we prefer to do it this way. Not only does it give you a better finish to your building, it also serves to further anchor your building to the ground.

Yes. We often are requested to construct on an existing slab and can marry the building to the slab in a variety of ways. We do advise our customer that the preferred method is to construct the building first, then pour the slab. The second preferred method is to cut through the concrete at the locations where the poles are to be set, to set the poles at normal depth and then to back pour the concrete in those cut areas.

Concrete is a commonly requested material. To be honest, we don't know much about gluing to concrete. You could check with some building sites. Cement is the adhesive that holds concrete together. It will take some research on our part but we are thinking about doing concrete. A very cool and specialized glue! It does its job then you can roll it into ball and ... well, have a ball with it. The glue that is used for "tip ins" (magazine jargon) is referred to as a Peel and Stick glue.

This is a very common complaint from our homeowner clientele. Some people try many products to control bad smells, including lime, charcoal, and even bleach. Plastic covers, due to their inherent leaking, sometimes aggravate the situation by keeping the ground humid and intensifying the smell. Our concrete floor system will totally encapsulate the ground and permanently eliminate the foul air from that area. Unfortunately, venting can actually cause more damage than good.

A thin piece of granite or other stone that ranges from ¾” to 1 ¼” in thickness. Granite was chosen the best counter surface for kitchens and for a good reason: It is durable, heat/scratch resistant, unique, rich array of colors, natural and bacteria resistant. Unmatched by any other product.

Bob, if you won the lottery what would you do to your home? (From your friends at the Remedy Building)

Good question. We use rectangular steel tubing in and around the tailgate area. This adds strength for our operable tailgate and also reinforces the rear body mounting area. We put drilled and tapped plates in the door post areas for mounting the doors and door latch pins. In the Bronco, we also provide a steel cowl section for mounting and fastening the dash, hood and swing pedals.

NEUTOCRETE® is a cementious product with a lot of minerals. And because it has so many minerals in it, the NEUTOCRETE® has an insulating value of R-6, which will help with the energy efficiency of your home. It will help reduce your heating and air conditioning costs because of its insulating values.