The movable knives are stuck open under the needle plate. Clean out any bird nest (build up of thread) or if you've had a needle break any needle pieces or any other obstruction which may be preventing the knives from closing completely. Close the knives completely, press SET to reset the code then try a manual trim or press START.

When IT Assistant detects that a memory slot contains memory that has an ECC error count greater than zero, an edit () icon appears next to that memory slot on the Status tab of the systems window. Click the edit icon to open a dialog box that enables you to reset the ECC count. IT Assistant 6.x integrates the launching of the DRAC II Web Console and the Array Manager console in-context from the Status tab.

This is a normal message and nothing about which to be alarmed. It simply means that the client canceled the connection before it had been completely set up - such as by the end-user pressing the "Stop" button. People's patience being what it is, sites with response-time problems or slow network links may experience this more than high capacity ones or those with large pipes to the network.

If you use the Forgot Your Password? feature to reset your password, and you get an error message (such as "Invalid session id"), then delete cookies from your browser and try again. To delete cookes in Firefox: Go to Tools | Options | Privacy | Show Cookies | Remove All Cookies | Close | OK Also note that the link in the password reset email is only good for one hour. If it has been more than one hour since you received the email, request another one on the Password Reset page.

The system reboot is the only supported approach prior to V7.3-2, but a reboot is obviously undesirable in various situations---there is presently no supported mechanism to reset error counts once the error(s) have been logged on these older releases. On V7.3-2 and later, you can use the DCL command: for an unsupported approach---and be aware of the potential for triggering a system crash, you need to determine the system address of the error count field.

Contact Customer Service at 1-800-819-7696 and provide your mobile number and ESN. You may also dial 1-888-445-4399 and choose option 3 to change your account profile. Your PIN code should always remain confidential.

Could you give the user the flexibility to change just the real important things rather than everything? >I took a look at tkbiff and it looks very nice. For the novice user, the >configuration file looks a bit overwhelming. If somehow the code could be >stripped out and just leave the user to change the real important things >would be nice. I actually wrote another biff which was vastly simplified. But simplicity has substantial drawbacks.

In IIS5 you had to explicitly set ServerController.ComInitialization to ciMultithreaded if you were using COM stuff like ADO. That setting automatically did the required COM initalization for all IW session threads. IIS6 initializes all threads itself, that is, you must not do it yourself, thus ciNone should be used.

You can change your account security code by logging in to My Prepay Account and selecting "Change account security code" under the "Account Profile" section. Enter your current account security code and your new 4-digit account security code and then click "CHANGE Account Security". Or you can press *611 from your wireless phone and follow the prompts. If you have forgotten your account security code and need to have it reset, please visit Contact Us and send us an e-mail and we can reset it.

A list of Point of Sale Reject Codes and Messages is located in the First Health Services Pharmacy Provider Manual on pages 35 - 45.

Error code 2020 means that both fax machines or computers never got connected. The problem could be that the number was not a fax number, or the wrong number was dialed. Also, if you do not have long distance service, and the fax number is long distance, you will get error code 2020. Also, be sure that the number you enter into our fax program to dial is the EXACT number that needs to be dialed. Look in the Send Fax box in the lower right hand corner, where it says, [Fax# Prefix].

The beam sensor may not be aligned correctly, (both the green and red lights on the top of the sensor, on at the same time indicate proper alignment). Move/adjust the sensor or the reflector in order to line them up and ensure both lights are lit. On TEHX or TMEX Machines if the beam sensor is properly aligned (see above) then check the emergency stop button; turn it to the right to release it.

Please do not email your questions directly to board users. There are many people here that will have the answer to your question and you might be helping others who are having the same problem. If you post to the board, you'll likely have an answer within a few hours (sometimes even within a few minutes!). Please do not ask us to email you directly because you can't get back to the board to check. It defeats the purpose of the board entirely (see above point).

If the LCD displays a NOT STERILE message, note the error code and consult the Troubleshooting section of your Operator's Manual.

quot;Sorry, MemberDirect was unable to process your transaction (code 000014029001). For assistance, please contact your institution." You may also get this message when you do not have an account selected (highlighted) to take the payment from

Please check your license code as they are case sensitive. If you get a capital "A" then you can not use a small "a". The best way is to copy/paste your license code in the appropriate fields of the registration box. You won't believe but 80% of the activation problems were a result of the misspelled license code. If this still didn't help you, please e-mail us (include your license code / order number in the e-mail for a faster response).

Error code (7) means that the license number submitted to our server has reached its maximum allowable number of activations. If you need to have this limit reset, please contact our support staff via E-mail to request a reset. Please have your license ID number listed in the body of any E-mail sent. Be aware that we generally prefer that Video Vault be installed on no more than two (2) computers simultaneously and they must be owned by the same person.

You have mounted the source DVD on a virtual drive and are using an old version of DVD-RB. Upgrade. The Freeware release is... Free.

Ninety Five percent of all our support questions are directly related to permission settings in the script. All of our programs and scripts come with instructions on how to install them. Always double check to make sure you uploaded the script correctly, Binary or ASCII, as required. Double check that the settings are correct (chmod) if using UNIX servers.

This error message generally indicates that you have been locked-out of Online Banking due to invalid logon attempts. To reset your access, simply contact us at 877-SOV-BANK (768-2265), main menu option 4. Transfers are limited to six (6) times per statement period. Please refer to the Personal Deposit Account Agreement for further details.

Sometimes a direct connection gets lost, but BitWise does not immediately recognize the lost connection. This can happen when the connection is not gracefully closed, such as when someone resets their home router or their ISP drops out for a minute. The typical symptom of a lost connection is that you do not receive message receipts for the messages you send. You can "reset" a direct connection by using the Reset Connection option on the Actions menu (in a conversation window).

You have to run the script from the command line. In other words, log into the server where your wiki is installed, then open a command prompt. Go to the installation directory, then go to the maintenance subdirectory. Run the following command: php changePassword.php --user=someuser --password=somepass Where obviously "somepass" is changed to the password you want to set and "someuser" is changed to the user name as it is listed in the table "user".

oil burner requires three things to make fire. Air, spark, and oil. Fuel oil is very stable and can only be lit if it is atomized. In normal conditions when your burner starts, the ignition transformer makes a spark the same time fuel is pumped through the nozzle, at the same time that air is drawn into the fuel causing fire.