The following output from servomaster_console would be a good indication that you're having this problem: Unable to initialize controller, cause: java.io.IOException: No compatible devices found. Make sure you have /proc/bus/usb read/write permissions. at org.freehold.servomaster.device.impl.usb.AbstractUsbServoController.findUSB(AbstractUsbServoController.java:259) at org.freehold.servomaster.device.impl.usb.AbstractUsbServoController.doInit(AbstractUsbServoController.java:474) at org.freehold.

Currently no any ways to work with hard drives, connected to RAID controller, because they work thru RAID BIOS and we don't have direct access to them.

Verify that the Yellow LED on the VME BioDrive XD flashes momentarily when you insert the device into the USB extension cable. If the Yellow LED does not flash, connect the device directly to the computer's USB port to determine if the problem comes from the USB cable or hub that you may be using. Also, in Windows, you can check in the Device Manager to see if the VME BioDrive XD is recognized by the USB controller. If it is not recognized, make sure that the USB port is enabled in the BIOS.

It is likely that you don't have viewing rights to the meeting that has a conflict. For example, the meeting that has a conflict could be a personal meeting and the attendee didn't give you any viewing rights ("View entries" or "View times only") to his/her personal meetings. In situations like this, Sundial will not be able to detect the conflict.

Rock solid. It's been used to run inside the DIY Zoning Project code for several years, 24/7/365, non-stop. Never failed.

There are mainly two kinds of USB controllers: UHCI (Intel, VIA, ...) and OHCI (Compaq, SiS, ...). To know the type of your USB controller, you can use the "usbdevs -v" command or the "dmesg | grep -i hci" command.

This is basically a known problem. The EISA on-board SCSI controller in the HP Netserver machines occupies EISA slot number 11, so all the ''true'' EISA slots are in front of it. Alas, the address space for EISA slots >= 10 collides with the address space assigned to PCI, and FreeBSD's auto-configuration currently cannot handle this situation very well. So now, the best you can do is to pretend there is no address range clash :), by bumping the kernel option EISA_SLOTS to a value of 12.

Yes, it is 16 positions! This control disc was "revolutionary" for its time, allowing for greater control with sports titles, but is also one of the reasons Intellivision never did catch up to the Atari 2600.

Yes, both positive and negative test results can supply valuable information, and many diagnostic tests don't operate in the 95% to 100% detection range. For example, the discovery of proteins called rheumatoid factors helped convince physicians that rheumatoid arthritis was a real disease instead of a psychological disorder, yet only about 70% of patients who receive a diagnosis of rheumatoid arthritis test positive for rheumatoid factors.

The main scenario here is deleting a file (by mistake or intentionally) outside of Team Foundation and then trying the get that file back from source control. If the file version has not changed the server thinks the user already has the file and does not copy it over. This is because the server keeps a list of files that the user already has and when activities are made outside of source control this list becomes out of date.

add the Telebutl.ini[dxb] entry r_on=1. This will allow recognition of any ringtone larger than 100ms.

Please take a look at the device manager "Start | Settings | Control Panel | System | Hardware | Device Manager" whether there is an entry which is called "menable3_0". If the driver has already been installed and this device is red marked in the device manager take a look at the properties where the problem is described and an error number is named. Look at the driver informations in the registry or let us know about this error number.

Check the connection cable. Make sure it is securely plugged into the phone and the USB port of the computer. The USB Drivers for the phone (usually on disk 1 of the kit) must be installed prior to plugging the cable into the USB port. If the phone was plugged in first, unplug it, then remove the drivers through control panel > add/remove programs. Reboot the computer, and reinstall the drivers prior to plugging in the phone.

In order for your PC to acknowledge the EzClone, you must firs press the "RUN"button for approximately 5-7 seconds. Once all three LED lights on the front panel of the EzClone light, you may then connect it via USB. This step ensures that the EzClone is switching to Exteranl Writer Mode. If it still does not work, make sure the USB Storage driver was installed for a Win 98SE system. Or try another computer to verify that there is any driver which was mistakenly removed.

No. However, version 1.1.01 of RCFS 2001 does have support for generic "game port USB converters." We have tested the Radio Shack device and the Rockfire USB Nest device.

Most new customers purchase monitors with an internal serial or internal USB controller installed along with the touchscreen. One cable connects the touchscreen to an available COM or USB port. Elo also offers external serial and PC-Bus controllers. The external MX serial controllers can either be mounted to the back of the monitor or allowed to rest on a flat surface, and power must be supplied (typically by a wall-mount power supply), so there are more cables than with an internal controller.

This depends. If you have Windows 95 ORS2 with the appropriate drivers for USB installed some USB controllers will work. Before making the purchase you should verify that your USB ports function properly and the device supports Windows 95.

Some ASUS motherboards have a 47 ohm resistor at R232 on the motherboard that reduces the power supply for USB devices to an inadequate level. The solution is to use a powered USB hub that will provide the proper power to the USB device. Isn't technology great? Many times simply re-installing your controller software (the latest version) will restore function. Other times its a bit more complicated. You may want to contact the manufacturer to see if they have published an updated driver.

Not only will it not work, you may damage your device. In order for a device to work with USB it must be compatible and have appropriate drivers. Some early releases of the Freestyle Pro and Precision Pro were not USB compatible; if it did not come with an adapter you are out of luck.

This is basically a known problem. The EISA on-board SCSI controller in the HP Netserver machines occupies EISA slot number 11, so all the "true" EISA slots are in front of it. Alas, the address space for EISA slots >= 10 collides with the address space assigned to PCI, and FreeBSD's auto-configuration currently cannot handle this situation very well. So now, the best you can do is to pretend there is no address range clash :), by bumping the kernel option EISA_SLOTS to a value of 12.

No. The PROcede is completely invisible to the ECU. The only way for the dealership to detect that the PROcede is installed on a vehicle is to physically look for the unit.

All Dolphin ISA Bus cards are non-Plug and Play, you must take the following steps to install the windows drivers: Click the Windows "Start" button > click "Settings" > click "Control Panel" > double click on "Add New Hardware" and let Windows do an automatic search. At the end of the search a "Details" button should pop up, click it. Finish the install.

If you change your audio environment suddenly and drastically, by for example disconnecting and reconnecting your microphone or dragging a piece of paper directly over the microphone, you will throw the voice preprocessor off balance. It will recover, but it will take time.

Some laptops with a PCMCIA controller made by ENE have been found to be incompatible with our Cardbus products (Indigo, Indigo io, Indigo dj, Layla24 Laptop, Mona Laptop). If you have such a laptop and are having audio playback problems with one of our products then this utility may help you. Go here to find out more information and download the utility.

Each USB controller on a computer can use up to 127 devices making it almost limitless. To get to 127 devices you do need to use USB hubs. Remember that each USB hub you use counts as a USB device. Back To Questions

Your Phoenix controller must have software version dated August 2003 or later to have the necessary interfaces to the PHX-Link. If your controller has the Soft Start programmable feature then you have a PHX-Link compatible controller. If your controller is not August 2003 or later revision then you will need to send your product to our factory for a software update to make it operate with the PHX-Link device.

Even with the latest Service Packs installed offering support for some USB devices the USB controllers require Windows 98.

If you have trouble with Windows or VRC not recognising the adaptor (chanels etc.) then clean all the connectors, because the USB side connector that goes into the computer could be dirty (oxydation). Also make sure that the Z-connectors aren't poluted or blocked by any production material or oxidation.