Students wishing to know how to connect to Boston College computing resources from off-campus should read the BC Help Desk document ' Connecting to BC using a modem to dial in '.

You will be asked to type in a name 'CTInets' and choose 'NEXT' to continue (Configure a modem if necessary) Next you will be asked to type in the area code and type '300 87 700', then select a country code 'Hong Kong (852)' and choose 'NEXT' to continue. Click 'Finish' to end configuration.

Input "CTInets" for the computer you are dialing and select your corresponding modem, then click "Next". Next you will be asked to type the telephone number '300 87 700' and keep the area code 'BLANK', then select a country code 'Hong Kong (852)' and choose 'NEXT' to continue. Click 'Finish' to end configuration.

Here are the key things to remember in networking the Borland Database Engine (BDE) for Windows Fair Management. The following assumptions are being made to allow this document to be ......

When a Windows agent is started on a machine with mulitple NICs (Network Interface Cards) it will attempt to use one of the two IP addresses, either the physical or virtual one. Verify the IP addresses using the "ipconfig" command at the DOS Prompt. If your physical card has an IP address and the virtual card does not, the agent will fail to start if the proper binding order is not specified.

Some users have experienced difficulties with routing when using a laptop which has both a network and a modem card used for UAB campus network access. If the machine had a network card with a 138.26.X.X number, the proper route is added when dialing into DPO because you have added a direct route into that domain since DPO is on that net. When you dial into BellSouth, you get an equivalent route for their explicit net. What is happening is that your existing network card has a route to 138.26.0.

On the Windows Setup tab, click on Communications (do not click on the check box next to Communications), then click on Details. Click to select the Dial-Up Networking check box, then click on OK on the Windows Setup tab, and click on OK. Windows 95/98 now installs the necessary components to use dial-up networking. Have your Windows 95/98 CD or disks ready.

Anyone who uses Windows Defender can join a worldwide network of users who help discover and report new threats. Microsoft analysts review these reports and develop new software definitions to guard against the new threats, so that everyone is better protected.

Each room is equipped with a network jack. You'll need an ethernet network card and a ethernet cable for you computer. Once physically connected you need to configure your computer to use DHCP. Additionally portions of the campus are setup to offer wireless access via 802.11 b/g for which you will need an appropriate wireless card.

Sure, you can. Create a primary partiton BEFORE your Windows partition (e.g. with PartitionMagic) and get a boot manager (I use the german tool 'Bootmanager', you can get a free trial version at http://www.bootmanager-pro.de).

In order to Add/Edit/Delete a speed dial setting, just press on the cell number you want to change for few seconds and choose the option you want.

Yes, WinGate can dial in to MSN through MS Dial Up Networking. Add [msn/] before your login name in WinGate's dialer (without the brackets of course). Without this addition, WinGate will not be able to login to MSN successfully.

In Windows 95/98: Go to My Computer > Dial Up Networking > Make New Connection. Type in Promotech for the connection name and 430-8318 for the phone number to dial. Click finish and you should see an icon 'Promotech' in the Dial-Up Networking folder. Right click on the icon and click 'properties'. Deselect the box that says "Use area code and Dialing Properties" and go to server types. Under "Advanced Options" check Enable Software compression and deselect all other options.

Dial plan is used to convert the number dialed to the number actually sent based on "dial number", "ddd prefix", "idd prefix", "ddd code", "idd code” these parameters. Parameter "use dial plan” contains 5 options: If the number dialed is prefixed by "idd prefix", the number sent will be the rest part of the number dialed dropping off the "idd prefix".

The process can vary depending on which operating system you're running. Step-by-step instructions for all supported operating systems are located here: http://www.Allstream.com/customercare/software.html#dialer-help

For any Windows based operating system (Windows 95/98, NT, 2000, ME, XP or CE), click here for detailed instructions.

A Detailed instructions are available in Section 6 of Internet Texoma's How To directory on this site.

Answer: This configuration is not currently supported. Page last updated: Tue Jul 24 22:01:55 2007; HPLIP Version: 2.8.2

Yes. If you have multiple network connections on any of your computers, you should turn on the firewall for each connection. If you're running Windows XP SP2, Windows Firewall is turned on automatically and it should not interfere with common tasks like file and print sharing. If you're not running Windows XP Service Pack 2, Internet Connection Firewall can interfere with file and print sharing and prevent your computer from finding other network devices.

Upgrade to 0.7.2 or newer. Older versions have a bug in Slirp caused by a 64/32 bit mismatch. Newer versions have a workaround for this, though the Slirp code really needs to be cleaned up at some point. If you can't find smbserver in My Network Places, try searching for it, e.g. (on Windows 2000) Start -> Search -> Files or folders -> Computers, then search for "smbserver". When found, double click "smbserver", right click "qemu" and map it to a drive letter.

We can clean the inside of the windows in your home. We do so upon request and at an additional charge. We will try our best to put you in contact with a reputable contractor to clean outside windows.

The required network information includes the SSL VPN gateway IP address, gateway address and DNS settings. The IP address is configured when you first install the software, but may be modified on the Network » Interfaces page. The DNS server addresses are configured on the Network » DNS Settings page and the default gateway (route) address is configured on the Network » Routes page.

Almost all desktop and laptop computers today are already configured to work on Concordia's network without any changes. Simply connect your patch cable to the Ethernet adaptor on your computer and to the network wall jack in your room. Then, visit www.cune.org to register your computer for full network access. Until your computer is registered, it will only have minimal network access.

A diskless, or network computer, uses a network file system as the root device. The kernel is downloaded via a TFTP server and the root device is mounted via an NFS server. The following servers are required on the host machine. The network client broadcasts a DHCP request. The DHCP server acknowledges with an assigned IP address, file name of the kernel and the root file system path. The diskless client downloads the kernel image using trivial file transfer protocol, TFTP.

We use two interfaces on the box, one management interface and one darknet interface to capture data. Detailed setup is described a little further along.

The Cisco cards will not require any special configuration. Follow the installation instructions and activate the card. Other brands of client adapters should work with their default configuration as well. If they don't then go to the Troubleshooting page for more assistance.

Up to eight network interfaces may be configured and they can also be bonded together for high-availability or network performance enhancement purposes.

This depends on what kind of equipment you have and where your node is located on the network (on the backbone, on the fringes). A typical sample configuration for a full member node is available at http://www.skynet.ie/~stephen/wireless/soekris-config.pdf.