If you have an older Acorn machine with a nine pin video socket, then yes and here is the wiring diagram :- Ideally each ground wire should be linked to a separate Arc pin. Also, depending on your SCART monitor, pin 16 may need a +5V input to it. Unfortunately the Arc 9 pin socket does not provide a +5V output so this will have to be sourced from somewhere else.

The second SCART on the DVD player is a pass-through designed for connecting another external input to your TV, e.g. a VCR or Digibox. However, this pass-through does not carry RGB, and so is not a good connection method if your Digibox can output RGB. In this case, you could connect your Digibox directly to the second SCART on your TV (if you have one and it supports RGB), or failing that, connect the DVD player to your TV using S-video (if supported).

It is possible to damage equipments when playing with PC vidoe hardware and workstation monitorts. If the monitor has standard video inputs, is workign properly, cable is properly constructed and everything is connected to properly grounded power outlet then the risk of damaging the graphics card is minimal. Some monitors can be damaged by sending wrong frequencies to them, so be sure that you send right frequencies to monitor.

Acorn computers are a British built line of computers that started with 6502 based machines and later became based upon ARM (Acorn Risc Machine) processors. Oddly enough Acorn computers were made by the Acorn Computer Group. Section 1.2 details those machines currently in manufacture and how to fetch a full list of all machines known to have been made by Acorn. Acorn machines are known for their innovation, flexibility and reliability of hardware/software. In January 1999 Acorn Computers Ltd.

There are lots of different ways depending on the hardware you have available but they all involve two routes, either via ADF files or HostFS. RedSquirrel doesn't yet support reading Acorn disks from the PC floppy drive but it does support reading 'disk images'. A disk image is a block copy of the floppy disk into a file on your hard disk. You can use a program such as arcimg that will read an Archimedes disk and write an ADF file.

All Acorn machines are equipped with a sound filter designed to remove high frequency harmonics from the sound output. However this does cause a muffled feel to the sound as on some machines the filter is a little too excessive and it filters out valid frequencies. Also the filter is optimised for 20.833 kHz output and has less desirable results when the output rate is changed. Accordingly people who do audio work often want to bypass the filter.

You might have overwritten the variable i with a number earlier in your program (or session, for that matter). You can reset i using i=sqrt(-1), or "clear i", or you can use j, or you can use the function "complex". Steve Lord tells me that an even better solution is to use 6i, which is unambiguously 6*sqrt(-1). In MATLAB versions >= 6.5, this can change a function which does not accelerate to one which does. For more details read http://www.mathworks.

A - If your TV has separate inputs for composite video and audio, then you just connect the video out from my game system to the video in on your tv and audio out from my game system to one of the audio in on your TV. If your TV only has an antenna input and no other inputs you need an RF modulator to modulate the video signal from my games onto an RF carrier so it can be connected to the TVs antenna input.

ACORN stands for A Classification Of Residential Neighbourhoods. CACI developed ACORN which is the UK’s leading consumer classification, based on Census & Lifestyle data and is used to describe the populations’ consumer lifestyle and purchasing characteristics. ACORN classifies the people and households within each postcode in the whole of the UK.

Unfortunately, we do not directly support this feature and we cannot guarantee that it will work properly in every situation (for example when the remote machine is connected via to a KVM). However, you can try it out. It is included in version 4.2 and later. Select a specific host entry and click on the Settings button. Then look on the Remote Options tab, you will see an option called "Enable blank monitor".

No, Macrovision will kick-in and render the picture unwatchable. That is unless you defeat Macrovision.

The machine must be visible to your machine and supporting SNMP access. You must also have a valid community (like a password) to request data from the machine. Some platforms, such as Windows ME, do not generally provide an SNMP Service. In such a case you can run the VisualLookout SnmpService. This will be automatically started if requested.

There's also a nice machine code monitor included for debugging programs. For detailed information read the IDE64 user's guide.

Yes, simply run the appropriate Setup routine for each monitor on the server. To provide access to all web reports from each monitor, it is recommended that each monitors is installed within the same local directory.

Yes you can connect your Xbox to your computer monitor using the 3rd party device called the X2VGA, which supports up to 1080i resolution (the same as the Xbox High Definition AV pack), and a toslink audio connector for Dolby Digital 5.1 surround sound support. Microsoft disables the high-definition video output on the PAL version Xbox(only sold in Europe, Australia, NZ, Hong Kong etc.), so it cannot work normally with the X2VGA. However, the Xbox consoles sold in North America, Japan, etc.

Yes, depending on the capture card. Some of the software only editing solutions require some external hardware. Please ask for the details.

The default configuration allows only unix domain socket connections from the local machine. To enable TCP/IP connections, make sure the postmaster has been started with the -i option, and add an appropriate host entry to the file pgsql/data/pg_hba.conf.

The J initiator will be automatically on the machine. There after you can always connect to the application even you do not start the machine as an administrator.

This is not recommended because Scratchbox CPU transparency requires your machine to do NFS exports and it installs a couple of suid-root / sudo binaries to your system (so that normal users can use Scratchbox).

Yes, in most cases. This feature requires the purchase of BABELink?. Please check with us to see if your ultrasound machine is compatible with BABE?.

To resolve this problem, all you need to do is to press the F5 key, and then view the properties of the file. You will see this message box only when ReadyShare encounters an unidentified error while trying to connect to the ReadyShare server. All you need to do is to click OK and wait while ReadyShare switches to the list view of your files in an attempt to continue connecting to the ReadyShare server.

redhat-config-securitylevel may be used to change firewall settings to, for example, enable incoming SSH and AFS client packets. It creates a file /etc/sysconfig/iptables. You should save a copy of this file beforehand, so that you can check against accidentally deleting wanted firewall rules. The firewall is controlled by iptables. To list current firewall rules and packet counters, type the following as root: iptables -L -v

This is not an easy thing go do. For input, many people have used a JPAC (http://www.ultimarc.com/jpac.html). This is the only pre-built solution that we are aware of. For video, unless you have experience setting up custom video modes in Linux, it's probably easier to go with Windows and an ArcadeVGA card (http://www.ultimarc.com/avgainf.html). This card will run at video modes that an be used by an arcade monitor.

Answer: Plug one end of the included iFIT.com audio cable into the iFIT.com jack near the machine's power cord or under the console. Next, plug the other end of the iFIT.com audio cable into the included adapter. Plug the adapter into an AUDIO OUT jack on your VCR. If the jack is already being used, you will need to purchase a 3.5 mm Y-adapter at your local electronics store.

Answer: Your exercise equipment connects to your computer using the audio cable that should have been supplied in the packaging with your fitness equipment. One end of the cable connects to the audio jack on the exercise equipment (normally at the base of the equipment or under the console). The other end of the cable connects to a speakers, line/audio out, or headphone jack on the sound card of your computer.

This is documented elsewhere. Press Ctrl-Alt-2 to get there, and Ctrl-Alt-1 to get back. If the host OS is not Windows, it is recommended that you pass "-monitor stdio" to QEMU which makes this unnecessary.

No, you only need one license for each place that you install our monitoring software. From that one machine and with one license you can monitor many servers, workstations, routers and other network devices.

It depends on what monitor you have, and what Acorn machine you have. There are two main types of PC VGA monitors out there... Fixed Frequency - These monitors will only display video signals with certain line and refresh rates. They will typically only display CGA / EGA / VGA modes. Multi Frequency - These monitors will display any video signal within a certain range, typically 30-50Khz line rate and 50-80Hz refresh rate.

When a video AGP add-in card is used, the Intel Extreme Graphics controller is disabled and the AGP connector operates in AGP mode. When an ADD card is detected, the Intel Extreme Graphics controller is enabled and the AGP connector is configured for DVO mode.