Answer: SelectSilver was designed to be cut-to-size maintaining their physical integrity without shedding debris into the wound bed. To protect periwound skin from maceration, the SelectSilver dressing should overlap the wound edges. A single dressing may also be used to treat multiple wounds on the same patient. Answer: SelectSilver has a non-adherent coating and has been found to be non-adherent to most wounds.

Answer: SelectSilver may be secured with an adhesive secondary dressing, roll gauze, tape, or medical adhesive

Answer: Some autolytic debridement of slough may occur when using SelectSilver resulting in thin film of residue under the dressing over time. If this is observed consider increasing the change frequency of the SelectSilver to ensure fluid management is not compromised. â??Wet-to-Dryâ?? techniques are not recommended.

Answer: SelectSilver dressings are commonly left on for up to 7 days. Secondary absorbent dressings should be changed more often if they become saturated without disturbing the wound bed.

Answer: SelectSilver has produced favorable results in a limited number of cases. This application, primarily with regard to burns, is being studied further. NOTHING ON THIS SITE IS INTENDED AS MEDICAL ADVICE - CONSULT A HEALTHCARE PROFESSIONAL ON ALL ASPECTS.

We sell teflex sheets to fit the 2500 and 2900 dehydrator models which are 14" x 14". they can be cut down to 12" x 12" to fit the 2400 model. You can also fold them if you prefer not to cut them. see: Click here for the excalibur 2900 page to see a picture and little write up. The horizontal air flow machines, I believe offer more even drying. Adjustable thermostat. The excalibur dehydrators have a thermostat to manually adjust the temperature.

Ceramic is best cut using a special diamond saw. Small prototype parts can be cut from piezoceramic sheet stock by using a razor blade and a straight edge to score the piezo surface and then making a controlled break. Even with practice this method does not yield straight-sided parts or repeatable cuts. Use at your own risk.

There is a 2 inch gap built in to the corsets at the back where it laces. Measure your waist and cut the corset closest to that measurement. Take it in or let it out until it fits as desired.

Answer: There is no need to pre-wet SelectSilver prior to application to draining wounds. SelectSilver may be pre-wet with saline solution, sterile water or wound gel for wounds requiring additional hydration.

Answer: SelectSilver performance has not been altered by any of the commercial wound cleansers tested, however it has been documented that silver can compromise the effectiveness of some debriding enzymes.

Answer: Excellent Application! SelectSilverâ??s ability to partition fluid away from the patient prevents maceration over an extended period of time. Wounds with significant drainage may require an absorptive secondary dressing before applying a compression dressing.

Answer: Yes. SelectSilver serves as an excellent wound contact layer or wick under negative pressure. No fenestration is required to move fluid through to the sponge layer.

Yes, we are specialists in resizing blinds and have the latest cutting equipment to make any resizing simple. Please refer to our Blinds Cut To Size page for further information.

We can cut parts up to 24" by 48" on our 50 watt laser, and up to 18" x 32" on our 25 watt laser. Our 50 is best suited for cutting, while our 25 watt laser can do light cutting and excels at engraving.

Our flyscreens are available in a number of different options, either as DIY kits, made to measure kits or we can fit them as part of a full installation service. For more information see our flyscreen options.

The Swisher trailcutter is designed to cut brush up to 1 1/2" in diameter. If you can drive over it with your ATV this trailcutter will cut it.

Yes, you can cut the bags to the right size, bottom and/or side seal using the heat sealer, extract the air through the front of the new custom bag size and then heat seal the top end.

Unfortunately we don’t cut worktops to size as we recommend all worktops are fitted onsite due to some walls not being straight etc. We don’t offer a direct fitting service but we have some contacts for kitchen fitters on the home page.

EcoCover's standard range will suffice for most requirements, noting in particular the overlap requirements for rolls laid adjacent to one another. Non standard sizes are easily cut either with large sharp scissors or a cutting knife / blade.

Procut will cut a 16 ft log, 24" in diameter. It was designed this way as I have found 80% of logs are this diameter or smaller. If you have large wood, look up the tree about 16 feet and see what size your tree is, you will probably find it is 24" or under. Why buy an expensive sawmill for just that butt log ?. Sell that butt log to another sawmill, you will have cash in your pocket, your own sawmill at a very low cost, and still have enough logs to cut.

Yes, we’d be happy to cut down your paper to any custom size. Our hourly rate for special requests—such as cutting or folding—is $60, billed in 15-minute increments. Please contact us to place your custom order.

Yes, if the standard sizes we carry to not meed your requirements, we can cut the foam down to the size that you need. You can also cut the foam yourself. Using a sharp carving knife or electric knife, the foam may be cut down to size as needed.

Yes! You can cut the KwikDek to any contour you wish. Simply put tongue oil on the raw edge and it will look like the rest of it in the cut area.

Answer: When you have a continuous span joist and one span is much longer than the other. This may cause an up lift situation on the shorter span. If you cut the top flange of the I-joist over the bearing point, it will alleviate the situation.

A 'Cut Size' banner is made by cutting a length of fabric from the roll and hemming it. That means that the final width of the banner will be 2-3 inches narrower than the width of the roll. So a 3'x8' Cut Size banner will actually measure 33"x96" (cut size doesn't affect the length). Cut Size banners eliminate wasted fabric, and save you money. If you order a 3'x8' Finish Size banner, it will actually measure 36"x96" after it is hemmed.

Answer: School Board Policy 8120.1 speaks to the preferred maximum sizes for new schools with a 2,000 student program capacity maximum for high schools. The policy which was adopted in 1986 was reviewed, corrected and reaffirmed by the Board on July 27, 2007. It is also noted that there was a study done in the mid-1980s to address declining enrollments at secondary schools in Fairfax County. This study may be found at: http://www.fcps.edu/schlbd/ChangingEnrollmentTaskForceReportPhase II.pdf

Answer: McConnell Hall and the Living Learning Community have extra long twin mattresses (although many students find regular twin sheets still fit these beds). Beds in Wallace, the Theophilus Tower are standard twin size. There is a waiting list available for students in Wallace who require an extra long twin, but the supply is limited and is distributed by greatest need.

It's an image in TIFFformat, which is frequently used, with the alpha cut out layer, which makes it possible to cut and paste the main subject of the image, without the background. For example, it will be possible to remove Father Christmas from its white background to paste it back on another photograph, another background...