screws to the ceiling surface. The wiring compartment has a standard size knock-out on top and is 3” in Yes. socket sets are supplied in 6 foot lengths and may be cut to a desired length; follow the detailed instructions supplied with the socket. No, doing that can harm the other transformers. Remove the inoperative fixture immediately. Take one of the operating units and install it in the inoperative location.

Yes. We recommend an electronic low voltage dimmer. Where a remote transformer is used, dimming can be accomplished by utilizing a dimmer to match transformer type (e.g. low voltage magnetic dimmer with a magnetic transformer).

Yes. All of our ceiling fixtures can be wall mounted. We can even elongate the arm length on the fixture and make a custom bend so the light can shine back at the wall. All we need to know is what radius is required. Additional costs will be added for custom curves and lengths.

Our tracks can be installed on either ceilings or walls. We offer different hardware for each. When placing an order, please indicate whether the application is intended for ceiling mount or wall mount.

Absolutely! You can install either type in any in-wall or in-ceiling applications. Footprint size and aesthetics may be a consideration. In-Ceiling speakers are smaller and have a smaller footprint (or overall dimension). However, the larger In-Wall speakers will mount safely to wall or ceiling. Either speaker can be used for either application. Typically, most rooms will only need a single pair of speakers to provide adequate coverage for background music or moderate listening volumes.

The answer is an emphatic and unequivocal Yes. A wall mounted TWIDS System will effectively prevent overclimbing of the wall, by sounding an alarm whenever such an attempt is made. Furthermore, the TWIDS are eminently suitable for installation on top of buildings, to prevent an unauthorized entry through the roof.

Yes, unlike other brands where a specific trim is designed for a specific housing, any one of the three trims will fit the sloped ceiling housings.

Use the Architectural Objects (Ceiling Objects; Ceiling Obj. #1) to mimic the slope of the ceiling, following the rise-and-run of the slope. The Basic Objects can also be used to model the horizontal and vertical components of the stair-step affect required to model the sloped surface.

Most manufacturers offer an optional "sloped ceiling" adapter that will allow you to hang your fan at any angle up to 48 degrees.

Yes, for standoffs we can add a custom swivel to the ceiling-mounting bracket, which will allow the rail system to hang plumb to the floor. Power canopies and surface mount transformer power feeds cannot use a custom swivel and must be custom bent to accommodate the pitch of the ceiling. What we will require is the slope of the ceiling to custom bend the power feed in the factory.

Not all projectors can be ceiling mounted. If you need this feature, ensure the projector supports ceiling mounting.

Yes. Our licensed and factory trained installers are familiar with all structural applications for an installation that meets or exceeds manufacturer specifications for system weight capacity

Our design consultants take preliminary measurements of your walls and we order over-sized acrylic “sheets”. Our installer custom cuts and scribes the wall surround at your home, for a precise custom fit to your existing wall.

define a new orientation for this orientation/slope in the TrnBuild "Project Initialization" window, and use it for the wall the window is in calculate the orientation / slope with a type 16 / 109 (solar radiation processor) and connect it to type 56. All surfaces are assumed to be black for long wave radiative exchange and radiative internal gains for surfaces inside the zone.

Yes - It can be either face or top fixed using the universal brackets supplied. For more information on this please see the How To Install section and view the instructions.

The reference kits ship with metal enclosures and single-gang wall plates. They can be mounted in drywall using the supplied hardware, however, these units are not intended for resale.

This can be done, however the CNK200 requires wall that is thicker than normal 4" wall. (Please verify this information with out Technical Support Department since the total thickness from the bezel's bottom edge to the last hinge for table-mount bracket attachment looks to be less than 4" as per the diagram posted on our website.) The termination switch should be ON if the local monitor is connected through a straight cable.

A wall controller can control upto 4 ceiling fans, but if your wall controller has a light switch, we only advise 1 ceiling fan per controller, because of the increased wattage/load on the controller.

Our full range can be seen at our showroom and workshops in Iwerne Courtney near Blandford in Dorset, which is open by appointment. Your local agent would also be delighted to show you samples.

The post-frame industry uses outside wall height as the industry standard for measuring size. A 10' wall height (or eave height) does not mean that there is 10' of clearance inside your building. Typically if you have a 10' wall, your clearance inside is approximately 9'4" because of header plates and ceiling joists. If you build up your floor with concrete then you will take away additional clearance.

Yes, you can. For detailed directions, look up the owner's manual or wall-mount kit instructions, because all such models can be easily wall mounted. Such kind of intermittent issues can prove to be very tricky. I would recommend contacting both your dealer and the Sony technical support team in order to avoid problems that may crop up in future. From your description it is tough to understand the possible issue with your TV set.

I've installed all the filters and plugged in the DSL modem but I'm not getting any internet connection. The "Ready" light is blinking. I've removed all the phone devices from their respective phone jacks and only have my DSL is connected but the Ready light is still blinking.

No attachment is necessary when using the compression kit to secure the pole in place. The shelves go between the poles and the wall and do need to rest up against the wall.

Although the ISS Designs shelving is described as a sleek minimal system, it is also strong enough for most medium weight requirements. That means it is great for your office, family room, den, kitchen, pantry and more.

The wall-mounted remote is a transmitter that communicates with a receiver in the fan canopy via radio waves. The remote comes with a standard size switch plate (the same as any light switch) and can be mounted on the wall in any location that has electrical power (the remote does not have to be mounted on the same electrical line as the fan). IMPORTANT: The wall remote MUST be wired in series. Please follow installation instructions very carefully.

Manablocs can be flush mounted right out of the box. For recessed mounting, a MBB2 mounting bracket is available (for studs spaced 16" on center).

Yes. Our LCD/TV monitors can be wall mounted. However depending on the model, the speakers might be built into the stand. Hence, in order to have the sound output, external speakers will have to be connected to the monitor - which can be done easily.

I am not sure what bin I have here, now. Can I tell if it is an Original No Butts Bin? It seems to have had a fire.