External adaptors are available for both desktop and laptop computers which connect to either a USB port or PCMCIA card slot.

The wireless modem connects to your computer via an Ethernet Port. The Ethernet port is located at the back of your computer If you do not have an ethernet port there are other options. Call you nearest reseller.

Yes, you will have to register twice: once for the wired Ethernet connection and once for the wireless connection.

The wireless modem connects to your computer via a USB or Ethernet Port. You need to check which of these you have free on your computer before you order your Unwired modem. These ports are usually located at the back of the computer. You can find pictures of these on the System Requirements section of the Unwired website. Your computer's USB port allows you to connect external devices (such as printers, digital cameras, etc) to your computer.

The WLA660's Ethernet port (RJ-45 jack) supports 10 Mbps over a 10Base-T connection (half-duplex only).

ITS's networking group does all new port installations and activations. Please call ITS at 962-HELP or open up a ticket at http://help.unc.edu. You will need the following information: building name, floor, room and port number(s).

You have several options. You can purchase a Network Interface Card (NIC) at any computer supply store. This will require a physical installation of the card into your computer. Or you can purchase a USB-Ethernet adaptor which converts a USB port on your computer into an Ethernet port. We have USB-Ethernet adaptors in stock for purchase and delivery with your modem.

Either one will work with the cable modem and service Wave provides. However, not all computer systems allow for a USB installation. Before your Internet installation, you must have a computer with a USB port, or have a 10 Base T Ethernet card installed in your computer.

When ETH connector (green) = ON, good receive/transmit on the Ethernet port. When ETH connector (orange) = ON, good physical connection to Ethernet segment.

On the SU that you want to deny customer access to, turn on IP filtering, and simply filter out the address or subnet that the customer is using. Configure the "User Defined IP Address" table to an IP range that is not in the range or subnet that the customer is using. When configuration changes seemingly by itself, this indicates there is a hardware problem with the unit. If warranty still applies, contact Alvarion tech support to RMA the unit.

A. The Targus USB Mobile Port Replicator with Ethernet is the world’s smallest expansion hub that provides instant peripheral device attachment and Ethernet via a single USB connection to Windows 98/ME/2000 based computers. Packaged in a small and attractive enclosure, the PA090U can fit any place on a desktop space. Add devices like mice, keyboards, joysticks, network, printers, PDAs, scanners, speakers, cameras, telephones and many more without rebooting your computer.

Please note: It is usually a bad idea to force the speed of an interface. If possible, leave in Auto-negotiate mode. Contact support@candelatech.com if you have questions. LANforge supports setting the ethernet port speeds through the GUI and CLI. The CLI Scripts page offers the lf_verify.pl script that has an example of setting the port speeds through the CLI. Information on how to set it through the GUI can be found in this section of the LANforge GUI Users Guide.

Unfortunately, this switch is defective. Please go replace you switch ASAP with your Vendor. If you have this switch over 30 days, then please E-mail rma@gigafast.com for future instructions.

Some DSL modems carry USB capability. This is useful alternative in instances where a network card cannot be installed. Please note that you cannot use the USB port of a usb HUB to extend the wire length between your modem and PC, or share the access to multiple systems. You can use the USB and Ethernet ports at the same time to facilitate access on two machines provided the advanced modem routing features are enabled.

It's about your security. It is possible to discover free sites on the net where people can list their homes. But an "open" system is very risky and not to be encouraged. People who pay even a nominal fee for a service are naturally more committed to the concept and are prepared to spend more time and effort in arranging the ideal swap. And if anything does go wrong, we will be here to help you sort it out.

Most computers sold today come with an Ethernet card already installed. If your's did not, ou can print the Installation Guide and install the card yourself, or you can contact the Help Desk, who may be able to walk you through it.

I've connected the USB to Serial adapter but it's on Com Port 5 (or higher) and your software only has Ports 1-4. This issue applies to the c\temp software only. This has been resolved with the new version of the MDAS-Pro software. If you do not have a copy of this software, please contact us.

If you don't have a serial port available but do have a USB port available you can purchase a serial to USB adapter that will look something like the following:

There are a variety of "aftermarket" products that will allow you to add a USB card to your computer. Check with either your computer manufacturer or with one of the manufacturers of USB cards.

The use of port 8080 is largely a relic of our beta deployment on PlanetLab, given that it is a shared test-bed. We hope to switch to using port 80 as soon as possible. Sorry for any inconvenience; in the short-term, if you can't access port 8080 due to a local firewall and still wish to use Coral, try finding an open web proxy running on port 80. For example, Google for the search term "cgiproxy start".

A list of common service port numbers (including web, email, and cPanel) is provided below. This is helpful in determining which ports to keep open when configuring your software firewall.

If you still have an active contract with your old Service Provider, then you will need to settle your existing contractual obligations with your Service Provider. Depending on where you are in your contractual term, this might prove to be an expensive move. Obviously, if your contract with your existing Service Provider has expired, then you simply need to provide your written notice of cancellation of your contract to them, and then arrange your new contract with your new Service Provider.

INX is not a traditional telephone service and does not have local number portability. Thus subscribers cannot move their numbers to a traditional telephone service.

ANSWER If you pre-arrange pick-up, we will meet you at your arrival terminal with a sign. In most cases, the best thing to do is to call our reservation # (954) 561-8888 after you have disembarked and gathered your luggage. Our vehicles are based in the Ft. Lauderdale airport, which is very close to Port Everglades.

It's a protocol for by many local networks, (LAN Local-area Networks) the origins of which came from Bob Metcalfe's Harvard's dissertation on "Packet Networks".