A Miracle Method refinished bathtub or tile wall can easily last 10 to 15 years with proper care and maintenance. In fact, many of our customers have told us their bathtubs still look and feel great 15 years after being refinished.

If your tile floor is properly maintained, you can expect it to last 20 years or more. You will greatly enhance the life of your tile floors or walls by using a properly installed cement backer board. Properly maintained tile walls installed over a cement backer board can also last 20 or more years.

Ceramic tile is a mixture of clays which have been shaped and fired at high temperatures, resulting in a hard body. Ceramic tile is made of two parts: the body, which is called the Bisque and the surface which is called the Glaze. Glaze colors are made from minerals such as gold, sliver, zinc copper, mercury cobalt and others.

Ceramic tile is characterised by its easiness to clean, its ability to be kept from dirt and any type of corruption. You can simply clean your floor with a damp cloth and if the surface is dirty or greasy, cleaning agents such as detergents or bleach may be used. The ability of ceramic surfaces to prevent humidity, also prevents the development of dust mites population and fungi that are easily generated. Ceramic tiles are naturally resistant to chemical and biological agents, and to friction..

Refinished bathtubs are often easier to clean than the original product. Make sure you use mild, non-abrasive cleaning products. Just as with a new bathtub, the finish or shine can be dulled by abrasive cleaners.

Layout - My husband is having trouble with the layout/cuts in the ceramic tile for our tub/shower area. There is an uncentered window in the primary wall. He keeps saying "no matter how I figure it, I still end up with 1/2" gap at the top of wall". Is there any way you can tell him what he's doing wrong? Thanks SOOO MUCH! Exterior Chimney - Do you have any information on tiling the exterior of a stucco chimney? Below freezing in winter.

Most orders are shipped within 7 days. However, please allow up to 2 week. Orders are then shipped UPS ground unless other requested.

To be used outdoors, the tile must be frost proof and unglazed for floor use. Make sure the absorption rate is 0.5% or less

Tile is actually the same temperature as the surrounding room temperature -- it holds warmth in a sunny room and would maintain a cooler temperature in an air-conditioned room. There are many installation products that will warm a tile.

ASTRA-GLAZE-SW® + units are made in Emigsville, Pennsylvania, South Beloit, Illinois, and Phoenix, Arizona. They are made using high purity, natural grain silica sands and a resinous binder cast onto a concrete block in a thermosetting, glazing process. The result is a hard glazed tile-like surface permanently molded onto one or more faces of the concrete blocks. ASTRA-GLAZE-SW® + blocks are fired at about 500 degrees Fahrenheit in a tunnel oven.

Use a carbide-tipped masonry bit or diamond drill bit; Fegular twist-drill bits can't cut through the fire-hardened glaze. Not necessarily. Porcelain tile is no different in temperature than anything else in the room except that it holds its temperature better because of its mass. Of course, cool is good in warm weather climates and it's easy to warm things up with an area rug or two.

There is no need to wax, polish or buff your tile installation. A damp sponge or mop is all that is necessary for daily maintenance. Special problems? Each of our locations carries a full line of Aqua Mix maintenance products developed specifically for ceramic

The initial cost of ceramic tile (when installed by a professional) is typically higher than many other floor coverings. However, because of its durability, it is also considered to be the least expensive in the long run. Occasionally, a tile may be cracked or broken, but the entire floor will never have to be replaced, except in extreme cases. Most other floors, such as carpet and vinyl flooring, will eventually need to be replaced. Tile runs the gauntlet.

Cleaning tiles is simple. Wipe tiles with a damp sponge or mop, using a small amount of soap less detergent in warm water. Heavy duty cleaning can be accomplished with a bleach and water solution. Avoid abrasive household cleaners, which will scratch your tile. (see tile care for more thorough information)

There are two basic types of tile: glazed and unglazed. A glazed tile is a hardened piece of clay covered with a protective glass coating, creating a sheen. The coating is sprayed or poured on as a liquid and then hardened in the oven. An unglazed tile is simply a hardened piece of clay. There is no protective covering.

Ceramic tile floors don't need any wax or floor finish, and all you have to do is sweep and mop them regularly to keep them clean and shiny. Mop with clear water (or add just a dab of liquid dish detergent), and change the water as soon as it gets cloudy. Too much soap or dirty water will leave a dulling or sticky film. Don't use brown or black nylon-backed scrub pads on ceramic tile, or you could scratch the surface.

The composition is what makes the difference. Ceramic tile is made of clay either white or red, Porcelain tile is made of porcelain. Porcelain offers less absorption of water, it is virtually impervious and has more sheer strength to it.

Yes. However, we recommend unglazed, frost proof tiles for outdoor use. Look for tiles with absorption rates of 0.5% or less.

Encaustic tiles are ceramic tiles in which the pattern or figure on the surface is not a product of the glaze but of different colours of clay. They are often of two colours but a tile may be composed of as many as six. The pattern is inlaid into the body of the tile, so as the tile is worn down the design remains.

Never wax tile. Your tile surface is lustrous enough as it is. When you use waxes, you are simply wasting your money and causing unnecessary build-up which sooner or later will have to be stripped.

Monterey Ceramic Tile and Marble is a ceramic tile and natural stone showroom. We are a resource to homeowners and the trade (architects, general contractors, tile contractors, and interior designers). We are an ideal source for those searching for something different and unique. Although we are not contractors nor designers, we are happy to refer to you independent credible contractors or designers that service the Southern California area.

For centuries, ceramic tile has graced the surfaces of temples, homes and buildings and provided an excellent material for containers and utensils. Discovered and enhanced by the ancients for its enduring qualities, ceramic tile is generally identified by its red clay content. Typical uses for ceramic tile are countertops, backsplashes, vanities and flooring. Requiring a stronger material than ceramic, porcelain tile is developed by composing finer bisques, finishes and firing methods.

This is a common myth in the bathtub refinishing industry. Your bathtub will not look like it was painted, since the material we use is more like a coating than a paint. In fact, our technicians pride themselves on the fact that it is quite difficult for an untrained eye to tell the difference between a brand new bathtub and one that has been refinished by Beautiful Finishes.

Our technicians come equipped with full ventilation systems to expunge the fumes that do naturally occur with the use of solvents. Although you may notice a slight odor after we are finished, this typically is gone in a few hours.

The durability of a bathtub refinished by Beautiful Finishes is very similar to that of a brand new bathtub. If properly maintained and no abrasive chemicals are used for cleaning it will last you many years just as a brand new bathtub would. Beautiful Finishes offers an industry leading 5 year written guarantee for all of our work. Most refinishing companies offer industry-standard warranties which are pro-rated, meaning that the warranty's coverage decreases incrementally over time.

A standard sized bathtub, in reasonable condition, takes only 4 to 6 hours to refinish. The tub will typically be ready to use within 24 hours or even sooner with special curing procedures.

Ceramic tile can be bonded to ceramic tile with a polymer modified thinset BUT your installation will only be as good as the weakest tile in the old installation.

Porcelain tile is a dense clay mixture that provides a very dense body tile. It is considered an impervious body which means its absorption is less than 0.5%. As in all things in life, not every porcelain is made equal and there are trade offs for using this type of tile. There are higher quality porcelains and lower quality porcelains. Red or brown body tiles come in a wide range of quality as well.