Generally they're stumbled upon. Some are very obvious though. Best solution is to switch the 3d view's Mode to Textures or Zone/Portal view as this gives you a very clear picture to work with for finding BSP holes.

West Marine carries sail repair tape that looks to be clear (kind of like packing tape) and is spec'd out to be strong enough for emergency repairs to spinnakers. This may work for you. Otherwise, the fabric backed tape comes in different colors. If West Marine or Layline do not have the colors you want, try calling you local sail loft. Here is the trick: ALWAYS round off the corners of the patch!!! If you leave the corner at 90' it WILL peel off eventually.

Many of the FAQs on the site were not properly numbered as they were developed, and for that reason they can be difficult to work with. To correct the numbering of topics, create a properly numbered category to take the place of the old one, and then edit each entry in the incorrectly numbered one selecting the new topic in the drop-down menu. I have duplicate numbered sections displayed in the FAQ, one is blank, but I don't see the duplicate when I'm editing it so I can't fix it.

Generally a black hole of any size. Any missing polygons. If when you move the 3d view close to it and you can see the blue grid. Those are definite signs that it's a BSP hole. Some BSP holes though can only be seen from certain angles. Those are the ones that you stumble upon.

The beads are handworked on a mandrel. Sometimes little bits of glass extend onto the mandrel, known as "stringers" this is a natural occurrence. A beaders helper - a small round file - available through most beading stores will help you rub the edges to prevent them from cutting your threat. Or use a little very fine sandpaper (400), but be sure to keep the bead wet while sanding it or you will loose the shine.

The most effective way to make a lasting repair is to cut away the rust around the hole and weld new metal in it's place. Another way is to fill with fiberglass. Then, seal the backside so moisture doesn't creep into the seam where the repair was made. Using steel can make a permanent repair and will last much longer than using fiberglass to fill the hole. Fiberglass has different expansion/contraction rates and won't adhere as tightly as welded metal will. It will eventually crack and fall out.

All details must be equal to material thickness. For further information: see Design Limitations [back to top]

Answer: Trusses should never be modified in any way without first receiving approval and an engineered "repair detail" from the truss manufacturer reflecting the modification. You should contact your truss manufacturer to get this information. Answer: There are a couple things that could be going on in this situation. The first is partition separation, which describes the gap between partition walls and truss bottom chords.

Yes we can. Keep in mind that the code generated by most WYSIWYG editors is really bloated. By that we mean that those editors usually place a bunch of code in your file that is unnecessary. Don't ask us why we don't know. The results of that create a couple of issues. For you your file becomes a lot larger than you really need. This costs you in bandwidth. Remember every time someone opens up your site in their browser they download your entire file. Unnecessary code and all.

The short answer to that is yes. Unlike some waterproofing contractors, we won't try to pressure you to waterproof the entire basement. If we determine that you will continue to have problems without doing so, we will advise you, but it's your CHOICE, it's your house.

We have never had any documented evidence that insects got in to an attic through our ridge vent. Wasps and hornets do not build nests in our products. The size of our openings are the smallest openings recommend by most major building codes for vent openings.

You may see pin-holes in your glaze because of underfired bisque, dust on ware, applying glaze to greenware, firing too rapidly, improperly adjusted slip, or firing wet glazes. To remedy, apply a thin coat of glaze before refiring, refire to proper cone.

Positively! We can replace and repair any drywall areas that may require attention. However, if water damage is involved we recommend that the source of the problem be resolved prior to replacing or repairing any of the damaged areas. We can also patch plaster walls and even match many classic textures done in plaster for an absolutely seamless repair. Please review our complete remodeling services online.

HEAT PIPES IN GENERAL, REDUCE CYCLE TIME. SINCE HEAT PIPES DO NOT SCALE OR CORRODE, THEY PERFORM CONSISTENTLY AND UNIFORMLY OVER THE LIFE OF THE MOLD, RESULTING IN LESS MAINTENANCE AND NO CHANGE IN COOLING RATE OVER TIME.

Believe it or not, they will be able to feed. The Niger/Thistle feeder is specially designed to only attract birds that will feed from thistle. You can review our seed chart to find out what birds will be attracted to this feeder.

Some web browsers have default settings that re-size images to fit the window. This will shrink the text and you will not be viewing the picture at it's best quality. You can change your browser settings to correct this. Their are instructions on our website on how to do this.

Very small tears or pinholes in the roof or floor are best repaired by applying pure silicone to the wound and letting it dry. Larger tears are best repaired by coating the area with pure silicone and then gluing down a patch of siliconized ripstop nylon cut to fit the wound. Netting tears are best stitched up. Scrap siliconized ripstop and no-see-um netting are available at no charge on request.

If you are having problems with Text Box Editor we suggest that you do the following steps, which will enable the standard text entry box. Note: this will allow you to use the right click option; this option is not available in Text Box Editor. After clicking on the "Set Text Box Editor Options" you will see the option to make the text box editor available or unavailable. Select unavailable and then click on the submit button on your right hand side.

You have two options. Either change your monitor resolution to a setting that will fit the screen, or download Maki's resolution patch.

The editor is Ray Boehm. He has been involved with function point analysis for about eight years and has been an IFPUG Certified Function Point Specialist (CFPS) for the past three. Ray spent the past most of that time working for a major systems integrator where he used function point analysis to monitor productivity and to estimate project effort. Currently, he is the Principal Consultant at Software Composition Technologies, a firm involved in function point training and consulting.

The Table Editor is a program will create tables and was packaged with PageMaker 4.0. For PM5 it was omitted from the Mac version. With PM6 it was back for both platforms, but on the PC, Adobe Table 2.5 was only available for those who use Win95. Others must use Table Editor 2.1. In PM6.5 and 7.0 the version is Table Editor 3. Most folks agreed that the early versions had some serious setbacks. Later versions are considered usable by many but there are still many limitations.

Get Adobe Acrobat from http://www.adobe.com, Fine Print's PDF factory from http://www.fineprint.com or FreePDF

The transfer function editors (subclasses of vtkKWParameterValueFunctionEditor) provide a wide range of functionalities but can be intimidating at first given the number of methods that can be used for customization. While the default settings should be good enough for most users, tighter situations may require to tweak the editors in order for all elements to show up without overlapping.

Editing can be a very demanding responsibility. It's more than a part time hobby, it's an unpaid activity that will compete with those that can actually lead you somewhere in life. Editing can be a thankless job, a duty reserved only to those who can pass the Test of Time, the Test of Commitment and the Test of Skill. If you think you're up to position of editor, then you may contact personnel officer Aaron Rice (elemental@mcmail.com) and he'll fill you in all the details you need to know.