A good quality Carbide Tipped Triple Chip saw blade is preferred when cutting Plexiglas. This reduces the amount of chipout on the opposite side of the material and produces a smooth edge. A Router can be used to cut Plexiglas as well. The Router should be at least 1.5 HP or better and with changeable collets for a 0.5" Shank quality 2 flute Carbide bit. This reduces the vibration and chattering when cutting and will produce a more smooth edge.

The slot should be cut 1 1/2" down from the center of the ridge on both sides. This is the same if you have trusses or a 2X ridge board. Cutting the slot larger will not increase the ventilation and may cause problems with the installation of the ridge vent. If you have a wide ridge beam the vent will have to be split. Either view our variation details or call 800-837-8368.

No, for PRE-CUT models. Every cut is already done, you just have to fold panes along the scoring (half-cut) lines and glue the ends according to set-up instructions. Yes, for PRINTED models. The details should be scored, cut out and glued according to the pattern drawn on the main surface.

A vast majority of our structures have the roof factory cut. Only on a few custom structures will parts of the roof have to be field cut. The trim, which is the ridge, hip, fascia, etc. has to be field cut to fit the roof. There are many other questions that may come to mind. Please don’t hesitate to email us at info@classicrecreation.com or call us at 1 (800) 697-2195 and we would be happy to assist you.

additional gage on the top face close to the cut (several top gages visible in pictures on home page) can improve the results, but it is more difficult to work with because you will cut very close to it. What the top gage will do, if you use one, is improve the results for the first 5-10% of the cut depth. The back gage all by itself can get very good results for stresses from about 5% of the thickness to 95%. Back to top

Stonehouse tops can be cut or altered using common hand tools used for cutting wood. For best results use a masonry blade or grit blade.

A strip cut shredder is good for ordinary business or personal documents: Invoices, packing slips, customer lists, vendor orders, and personal notes. You should use a strip cut shredder for anything that might be subject to casual curiosity or low-level snooping. A cross cut shredder is good for sensitive documents: Ledgers, bank statements, credit card statements, critical business reports, salary reports, and personnel records.

The cut-off time for same day transfers is 10 PM (EST) on a regular business day (regular business days are Monday - Friday excluding holidays). Transfers made after 10 PM (EST) will be available the following business day.

Yes. The cut-off time for bill payments is 9:00 PM (EST) on a regular business day (regular business days are Monday - Friday excluding holidays). Payments scheduled after 9 PM (EST) will be processed on the following business day.

Possibly. If the tree is in the street right-of-way, contact the Engineering Department at (503) 681-6146 for a permit. If the tree is on your own property, please contact the Planning Department at (503) 681-6153 before cutting down the tree. Be prepared to give the street address or Tax Lot I.D.

It is not expected that any trees will need to be removed within Madison to accommodate any improvements to the rail corridor, since all construction on the project would occur within the rail corridor right-of-way.

The City has a Tree Preservation Ordinance protecting trees growing on private property that are greater than a minimum size. Please see Tree Services for an overview.

Sprinkool's tubing is supplied in 15-foot lengths, and systems are designed in what we term as a "15 by 15 design". This means that the Fields-lines as well as the Sprayheads are 15-feet apart. Although some tubing will need to be cut, the system is designed to maximize material and minimize cutting.

Yes, if the standard sizes we carry to not meed your requirements, we can cut the foam down to the size that you need. You can also cut the foam yourself. Using a sharp carving knife or electric knife, the foam may be cut down to size as needed.

If the tree is on City property, please call the Detroit Recreation Department Forestry Division at (313) 224-1111. If the tree is on private property, the property owner should contact a tree service company.

This product was designed to help you properly measure and cut the overlay to match your display screen. It will also allow you to use the product on other consumer electronics that may have a screen. Instead of buying the product to fit on just a PDA, you'll also be able to protect your cell phone, digital camera or camcorder. Do not attempt to cut the overlay when it's on the screen. You could end up damaging the display screen.

No, but mowing will increase the evaporation process of the wastewater, helping with the filtration process of the nitrogen present.

If we mispronounce a word, omit a word, or make a punctuation mistake, we will provide a re-read at no extra charge. Just request the re-read by emailing info@voicetalentnow.com. If you change your copy, you must fill out a new order form and you will be charged for another spot.

The cut sheet (supplied by your engineer) is required before the Pre-Construction meeting is scheduled.

Yes, if you are a male applicant, you will have your hair cut to military standards. If you are female, hair may be worn up according to standards or cut above the shoulder.

If you need your water cut on, simply contact the water billing office at 989-3055. If you need your water cut off , call the same office and ask to have a final reading for your meter.

You can go anywhere to get your hair cut as long as the donation guidelines listed on our website are followed. We encourage our donors to go to a salon they are already familiar with so they will be comfortable when making their donation. View Donation Guidelines.

Cutting the hair shorter does not really reduce your workload much and we wouldn't recommend it especially it the kids are going to resent it. Most head lice activity takes place close to the scalp where the warmth and food is. Once long, thick or curly hair is oiled it can be combed very easily and rapidly and length makes very little difference. Dred locks are about the only genuinely problematic kind of hair as combing is pretty well impossible.

In short, the final version of the finished film. Although it may receive a small edit here or there in the next few weeks, the film is essentially "locked" into this form.

You bet. Just let us know when you place your order. But are you sure we can't tempt you into trying our cut-in service? It's free and just check out a few of the great styles we can offer...

the end of 2000, DUI responded to a demand from the cave diving community in Florida to make the TLS350 closer fit to lessen drag especially for those using scooters for long distances. This type of suit is only available as a Special Production and for the TLS350. DUI will use the provided measurements and will make the circumferences of the suit smaller than it typically would for someone of those measurements. It is critical that we have extremely accurate measurements.

A Road Opening Permit from the Township Engineer's office is needed. The application fee is $100 and a $500 partially refundable deposit is also required to cover Township inspection costs. The permit application may be picked up at the Engineering Division Office. Please include with the application a detailed drawing or sketch of the road opening, number of linear feet of road, depth of trench, name and address of the contractor and expected date of work.

Dark chocolate is actually a very beneficial food in and of itself with excellent antioxidant properties. The problem comes when it is mixed with fat and sugar, which is usually the case. You can buy no-sugar chocolate bars, which are better, and have a small piece, because they still are very high in saturated fat. Our Ray & Terry's Supreme Chocolate Meal Replacement Shake has cocoa without either sugar or added fat.