As Freecom does not have control of the application of CERAM-KOTE, Freecom can only guarantee that CERAM-KOTE is manufactured to our strict manufacturing specifications and the testing accomplished to the best of our knowledge is correct. However, it is the responsibility of the end users to determine if CERAM-KOTE will work for them.

As CeRam-Kote does not have control of the application of CERAM-KOTE, CeRam-Kote can only guarantee that CERAM-KOTE is manufactured to our strict manufacturing specifications and the testing accomplished to the best of our knowledge is correct. However, it is the responsibility of the end users to determine if CERAM-KOTE will work for them.

Most CERAM-KOTE coatings are considered two component systems. Part A (base) is a ceramic/epoxy solution that is mixed with Part B (curing agent). Please see each individual Product Data Sheet for mixing and application instructions. With extreme care, a two-component kit of CERAM-KOTE may be broken down into smaller quantities. Careful and exact measurements must be made to assure that the proper ratio of Part A to Part B by volume or by weight is maintained.

Typical orders for CERAM-KOTE products in Freecom's published colors may be shipped within three days, depending on quantity. Special colors that require color matching may take three weeks. This lead time applies to all formulas.

Yes. A short nap roller (approx. ?" or 6.35 mm) of good quality is recommended. The shorter the roller nap, the lesser the stipple effect.

Freecom does not recommend coating over old coating as the adhesion will only be as good as the old coating. If cleaned properly to remove all contaminants, CERAM-KOTE coatings will adhere to old coatings. Care must be taken as CERAM-KOTE coatings may soften old coatings and cause them to blister and disbond. If the old coating disbonds, then any of the CERAM-KOTE coatings, which adhere to the old coating, will come off with the old coating.

Due to the unique chemistry and characteristics of its inert ceramics, CERAM-KOTE coatings can be applied to just about any properly prepared surface and provide a protective barrier to that surface. Regardless of the industry, (chemical, corrosion and abrasion) problems exist. CERAM-KOTE coatings can help solve those problems.

Dry to handle time is totally dependent upon the temperature of the day and/or the environment. The higher the temperature, the shorter the time needed before the coating may be handled. The colder the temperature, the longer it will take before the coating may be handled. At ambient temperature, 72?F (22.2?C), CERAM-KOTE epoxy coatings will typically be dry to the touch usually within 3 hours. CERAM-THANE urethanes will be dry to the touch within 7 hours.

When cured, CERAM-KOTE epoxy coatings are designed to be as environmentally friendly as possible. Our epoxy coatings are considered food grade* and may be disposed of in any land fill. Consult your local government agency. CERAM-KOTE coatings can cause skin sensitization. CeRam-Kote recommends the use of protective clothing. The use of an organic-filter respirator is recommended when using any CERAM-KOTE coating material.

Most CERAM-KOTE coatings are available in five gallon kits, one gallon kits and quart kits. Each kit contains one container of Part A and another container of Part B. They are packaged together in an internationally approved shipping container. Pint and 6.5 oz. touch-up kits are available for some products.

CERAM-KOTE epoxy coatings use modified epoxy resin as the binder for the ceramic powders. Epoxies are not known for their resistance to UV (Ultraviolet) light. Due to the molecular structure of epoxies, the UV light breaks down the molecular structure and causes "chalking" on the surface. This does not affect the performance of the coating in preventing corrosion for many years.

Carbon Steel, Stainless Steel, Aluminum, Brass, Titanium, Galvanizing, Plastics, Concrete, Fiberglass.

CeRam-Kote 54? ATM is registered with the American Bureau of Shipping as per certificate #99-HS27360-X and ABS Certificate of Design Assessment #03-HS391002-PDA. CeRam-Kote 54? has DNV (Det Norske Veritas) Type Approval Certificate #K-1966 for protection of structural steel in ships ballast tanks, submerged in seawater and in splash zone.

All of the CERAM-KOTE coating systems call for a white metal (NACE 1, SSPC-SP5, Swedish Standards SA-3) finish. Each CERAM-KOTE coating system calls for specific anchor profile specifications. Please refer to each individual Product Data Sheet for more anchor profile information. Freecom, Inc., does not recommend less than a near white (NACE 2, SSPC-SP10, Swedish Standards SA-2?) finish. Adhesion strength depends on proper preparation of the surface to be protected.

CERAM-KOTE epoxy and urethane coatings should not be applied below 40?F (4.4?C) or to a surface temperature above 120?F (49?C). If the temperature is below 40?F (4.4?C), the catalytic reaction is halted between Part A and Part B. If the temperature is above 120?F (49?C) the solvents (used in most of the CERAM-KOTE coatings) are forced out of the coating film too rapidly, the coating film gels too rapidly, and the coating film can end up with holidays.

These values are theoretical coverage numbers and depend on weather conditions, complexity of the substrate, and application technique:

Due to the heavy loading of ceramic particles and solids into our CERAM-KOTE coatings, a true high gloss cannot be achieved with CERAM-KOTE epoxy coatings. Only CERAM-KOTE urethanes, although loaded with ceramics as well, can achieve high gloss. A semi-gloss may be achieved with proper application and curing techniques (CERAM-KOTE 2000 and CERAM-KOTE 99 formulas have better gloss retention than CERAM-KOTE 54?).

CERAM-KOTE coatings are coatings that utilize various highly modified resins. These resins are then loaded with different types of ceramic particles to achieve the attribute needed, whether that be abrasion, chemical or corrosion resistance. CERAM-KOTE coatings encapsulate surfaces with a ceramic shell that protects the surface from its particular environment.

Typical orders for CERAM-KOTE products in CeRam-Kote's published colors may be shipped within three days, depending on quantity. Special colors that require color matching may take three weeks. This lead time applies to all formulas.

CERAM-KOTE coatings are applied direct to the substrate (i.e., no primer is needed). This saves time and money. CERAM-KOTE coatings also provide protection from chemical, corrosive and abrasive environments beyond the chemistry of the typical epoxy systems.

CERAM-KOTE's ability to adhere to a substrate is one of its major advantages. If applied over a primer, the adhesion strength is only as good as the adhesive strength of the primer. Adhesive strength is much higher using CERAM-KOTE alone without a primer than it is with a primer. In addition, the elimination of a primer eliminates the cost associated with the use of that primer and makes the use of CERAM-KOTE more economical.

Yes, but only in countries where it has received governmental approval. CERAM-KOTE 54? has been approved for use in potable water tanks in Scandinavia, New Zealand and the United Arab Emirates.

If applied in two passes as specified, CERAM-KOTE coatings will not run or sag. The colder the temperature the longer the time between passes. The solvent must be allowed to evaporate from the first coat before the second coat is applied. Solvents evaporate at slower speeds in colder climates.* CERAM-KOTE SPG is 100% solids, hence can be applied thicker in one pass with no detrimental effects to the coating film. Freecom can also allow other formulas to be sprayed in one pass.

CERAM-KOTE is a coating material designed and formulated to be economical and environmentally friendly. Its ability to be applied without a primer makes it more economical to use when comparing to other coating systems on a price per square foot (square meter) applied cost. It saves money while CERAM-KOTE's outstanding performance properties provide long-lasting protection to the substrate. CERAM-KOTE coatings are formulated to have low Volatile Organic Compound content, too.