Yes. Inserts are available in natural vent and direct vent units. Flue liners are used to exhaust flue gases. We can assist and advise you which insert and vent application is required.

Yes. Gas inserts are available in chimney vent and direct vent models and both are installed with aluminum liners running up the chimney. We are able to assist you in choosing which model and size would be needed after the measurements of the fireplaces have been determined.

All of our wood and oil fireplaces require a chimney, either a masonry or A vent, stainless steel chimney and in the case of our oil stoves, L vent is also acceptable. The diameter of the chimney must match the size of the fireplace flue collar to effectively vent the products of combustion. Consequently, an existing chimney may need to be lined with a stainless steel liner to meet venting requirements of a specific fireplace.

Although the frequency of your fireplace servicing and maintenance will depend on use and the type of installation, you should have a qualified Mr. Fireplace service technician perform an appliance check-up at the beginning of each heating season.

No! The beauty of Regency Direct Vent technology is that you do not necessarily need to go up through your roof to terminate the venting. All you need is proximity to an outside wall, the distance to which depends on the model you choose. Not only does this make installation more flexible, but it also keeps the costs down. And with our sleek and attractive patented AstroCap horizontal termination cap, you won't be cluttering up the outside of your home either.

Vent free fireplaces are fireplaces that do not require any type of vent system. Instead, they are designed to burn clean and the combustion by-products allowed to flow into the room the fireplace is located in. Stringent requirements ensure that these fireplaces not only burn cleanly, but that they are located in rooms of sufficient size to ensure an adequate supply of fresh air is always available for the combustion process.

Direct Vent Gas Fireplaces eliminate the need for a conventional chimney. These fireplaces vent directly though a wall or out the roof. Unvented Gas logs utilize new berner technology and high burn temperature to keep the carbon monoxide levels down to an acceptable level.

There is no chimney or venting required with an InFlame Fireplace. The Sunjel? Premium Ethanol Alcohol Gel burns clean, free of smoke and fumes and into water vapour, eliminating the need for standard exterior venting. Sunjel? Premium is certified by Environment Canada to be burned indoors without a chimney. All InFlame Fireplaces are also ULC Listed (Underwriters' Laboratories of Canada) for 'un-vented use' to Canadian Government Standards. 9.3-M86 AND CAN-ULC-S610-m87. Back to List

Martin’s vent-free ISD insert has been approved to be installed to existing masonry or factory-built fireplaces (which must be approved for inserts by its manufacturer). It does not require any type of vent and is best suited for those who desire vent-free and want a blower. The unit comes with optional surrounds and can be installed to fireplaces that have sustained cosmetic damage. Martin Hearth & Heating inserts are CSA approved and equipped with an ODS or oxygen depletion sensor.

Not exactly. Direct vent gas fireplaces need to be vented outside, however, this vent, or "chimney" can be run horizontally through an outside wall. In this sense, it does not require a traditional chimney that extends vertically above your roof line. You should be careful however not to confuse direct vent with unvented gas hearth products.

How can I make final plans for my Mendota installation? I will need information for the building inspector, plumber, contractor etc.

No, this unit will not exhaust properly vented into a chimney. It must have its own three or four inch pell vent piping throughout its entire installation.

No. The inserts are designed to have adequate space on the sides for air exchange. Correct measurement of the existing masonry fireplace is important. The insert should never be forced into a space that is too small.

A - Only sealed direct vent fireplaces can be vented horizontally out a wall. The only exception would be an open fireplace with a power vented system, which is usually noisy and not recommended in residential installations. Q - I have a wood-burning brick and masonry fireplace that faces one direction. We would like to open it up so that is see-through and put in a gas insert.

These type of fireplaces do not have a sealed combustion chamber and relies on the buoyancy of hot gases to vent effectively. They must be installed either with an existing chimney that meets the local building code standards or they can be installed using a B vent which is a vent pipe that must be installed to the same parameters of a masonry chimney but can be enclosed in combustible material. They draw air (oxygen) necessary for combustion from the area surrounding the fireplace.

We bought one of your stoves 2 years ago and love it. However, the thermocoupler is faulting and needs replacement. We have misplaced our owners manual. Where can we find a new part or can I order one from you direct. Model #C9740LP serial # 002365. I just purchased C9947N and installed it Tues. evening (the 15th) from Quality Farm And Fleet, in which is going out of business. I have a considerable amount of carbon monoxide. Everything meets standards in the manual.

All vent-free appliances, whether natural or propane, produce water. The accumulation can range from 3/4 to 1pint of moisture per hour in the room. Under normal conditions, this does not cause a problem. However, if you have a problem, you will need to provide an outlet for this moisture. This can be accomplished by providing adequate ventilation or using a dehumidifier to help control the moisture. Yes/No.

Yes. No electricity is required to operate a direct vent fireplace. Direct Vent Gas Fireplaces operate via a millivolt valve system. During a power failure, your fireplace will be a secure source of heat.

No, the State of Massachusetts, as well as some other states, prohibits the installation of unvented fuel-burning heaters.

Vent-free gas log sets can be installed in most masonry fireplaces, as long as the set's clearance and ventilation requirements are met. For installation in prefabricated fireplaces or fireboxes, follow the fireplace manufacturer's recommendations, as well as meeting the set's clearance and ventilation requirements. Refer to the log set's owner's manual to determine clearances and unconfined space requirements.

It is possible to install a fireplace using your existing masonry chimney. The chimney must comply with the building code of your country, state or province. It usually needs to be lined with refractory bricks, metal, or clay tiles sealed together with fire cement. The diameter of the chimney must be the same as the fireplace's flue outlet.

im buying a new ac ready furnace for my mobilehome,., i have the paperwork from the previous owners purchase of a new kenmore outside cooling condenser,tech info and so on but it does not say its a 1 ton or3 ton or3.5 ton ,HOW CAN I FIND OUT WHAT TONAGE IT IS SO I GET A PROPERAC READY FURNACE THE FURNACE IM LOOKING AT WILL HANDLE UP TO A 4 TON I am interested in purchasing an Eden PURE portable infared heater, Model 1000, which the internet site states is 5200 BTU.

Yes. They can be vented or the damper can be closed and be burned as vent-free for an excellent source of heat.

Hoods are designed to deflect heat from wood such as a mantel. Check the installation instructions for your log sets to see if the mantel height requires you to install a hood.