Each solar module is approximately 5 feet (1.5 meters) long and 2½ feet (0.75 meters) wide. The modules are always grouped in a set of four, and the minimum number of modules for our smallest system is twelve modules. This requires an area of at least 120 square feet (11 square meters).

Very easy. 100 square meters is 1076 square feet. Surfaces are given in square meters, written m2 or m2.

Meter to feet Length ratio=3.3 (One meter equals 3.3 feet) Sq.meter to sq.feet area ratio= 10.76 (One square meter equals 10.76 square feet) In order to get the feet equivalent, you just have to multiply the meter amount with the length ratio (3.3) to get the amount of feet, or divide the feet amount by the length ratio to get the meter amount. For areas and spaces, just multiply the square meter amount with the area ratio (10.

You can have as much land as you choose. Change the amount of land you have and your monthly fee will adjust accordingly. See Virtual Land: Cost.

All AstroRide and AstroSlide is priced per square meter. To help you in your estimates a meter is approximately 3.25 feet. A square meter is approximately 10 square feet.

Right click on the layer you want to perform a calculation in. Then chose the Open Attribute Table option. Once in the Attribute Table, decide the column(s) in which any calculations need to be made. If you only want certain records within this column to be calculated, select them at this point, otherwise, the entire column will be calculated. If you want to be able to undo any calculations made, start an editing session (Editor-Start Editing).

the UV lamps and /or sleeves need to be periodically removed from the reactor chamber, you must leave at least double the length of the disinfection system to facilitate removal. A typical 5 USGPM UV system would require approximately 45" of space either vertically or horizontally.

The Allergy Machine™, HealthMate™ and HealthMate+™ have 60 Sq. Ft. The HealthMate Jr™ Model has 30 Sq. Ft.

By best approximation, to get sq. meters, divide sq. ft by 10.75, or multiply sq. meters by 10.75 to get sq. ft. The conversion rate is currently 44 INR to one dollar. This is a fluctuating rate. Divide INR by 44 to get close approximation of prices in U.S. dollars. To get the current rate go to: http://wam.org.

The heater model and capacity are not necessarily a function of the square footage of the area needing to be heated. The model generally is chosen after the Btu/hr heat loss for the building or spot area to be heated has been determined, which is a function of not only the size of the area, but geographic location, building materials, building usage and other factors. Area coverage could be as little as 500 sq. ft. or as much as 10,000 sq. ft.

One device is adequate for the treatment of max. 150 cubic meters room.(about 450 sqft). However, it is recommended to use it close to you in the room

Generally speaking, for an adequate air exchange rate, you can expect up to 500 sq. ft. coverage for the SE400E, and around 700 sq. ft. for the SE800E. - based on moderate concentration levels w/ 8 ft. ceilings. Individual results will vary based on environmental variables. To find out how many of which air cleaner you need, try our air cleaner calculator in the Buyer's Guide.

kW is more or less equal to 10-20 m² depending on the insulation of the house. It is recommendable to choose a smaller stove as the combustion will get cleaner if you fire hard in a small stove instead of slumber use in a large stove.

The bezel of the re-issue SUB 300T has graduations in Meters. There are 2 major diving institutes in the world; SSI and PADI, their courses adhere to the metric system. This was the reason for DOXA to choose the metric bezels but after they received lots of inquiries regarding a SUB 300T bezel with Feet graduations, they decided that the new SUBXXX bezels will be available in Feet, as they were on the original watch.

For units that have been purchased after 2000, when you open the cap (not the battery end) there will be 4 switches on the opposite side of the circuit board from where the cap snaps in. The 2nd switch from the right (or the 3rd switch from the left) is the unit of measure switch. For Meters, push the switch back (away from you), and for Feet, pull the switch forward (towards you).

We have 20 warehouses across Canada supplying Unisource Canada with over 1,700,000 square feet of warehouse space.

Thatâ??s a hard question to answer because many factors can affect the cost of your project, including its size, complexity, accessibility, and quality of finishes that you choose. We can give you a better idea after we have visited your home and assessed your needs and desires.

With the rapid drop in prices for hard drives and optical media, it costs much less to store documents on an imaging system than with paper. A single page typically occupies around 50KB of disk space if the image is stored in TIFF Group IV. Each gigabyte (GB) of storage space (which costs only a few dollars) will hold approximately 20,000 pages.

Most of a GSHP installation is underground. Inside the house, the heat pump units are about the same size as a traditional heating and cooling unit.

The AltME program is only .5 MB, so it is fast to download and takes very little disk space. Each world will also require some disk space, but most worlds rarely use more than 1 MB. We think AltME would be terrific on cell phones, and we hope to add that feature just a soon as possible.

In captivity, it's not as much as we are likely to think because in the wild the cats primarily need a lot of roaming space for eating and hunting reasons. Back to Top

The e-mail agent installation files require approximately 25 MB. Many of the core programs, such as Perl and MySQL, required to run the agent software, may already be installed on your system. Another approximately 100MB (1 GB) of memory will be required if they are not. Sizing the database is a function of program activity - more e-mail and larger attachments require more storage.

Answer: The system takes-up very little space: the purifier, which is only 31cms high, will fit neatly under the sink in any size base unit. Answer: No. The system has been designed to work from mains water pressure, does not require the use of any chemicals and the cartridge is constructed entirely of natural .

The answer to this question is generally "depends on the type of data being indexed" (mostly media like photos/movies vs. lots of text documents, which take up more indexing space), but 5-10% of the size of the data to be indexed seems to be a good ballpark figure. Yes! As of Beagle 0.1.0, NFS home directories can be indexed. Note however that this will be an extremely slow operation, as every byte of your data has to be transferred between the NFS server and your client desktop.

a. Yes it is quick and easy, trace with the stylus pen around the area and the program calculates the square feet of any area, also trace along any straight or curved length and the program calculates the exact linear feet.

Truthfully, that can only be best done if the entire floor plan of the home, insulation value and needs are all considered. It is always best to speak with a dealer, tell them about your home, life style and describe what your goals are for heating with wood.

There are 43,560 square feet in one acre. Therefore, if the size of a property is 0.20 acre, then it would measure 8,712 square feet (43,560 x 0.20 = 8,712).

We go by unit price and not by square feet due to the fact that square footage is not accurate and often works out to be more expensive. If you have a lot of windows, we can offer a volume discount. Unit price varies depending on how many windows you do and what is involved.