To purchase an extra REMOTE CONTROL contact DIRECT WHOLESALE at 1-800-659-0764, have the Installation Manual along with the Model number for your unit when ordering a new Remote Control.

Yes, this can be done by simply using remote transmitter #1 and by simply connecting power to each unit and using remote transmitter #1 to initiate the unit. This will let transmitter #1 operate units 2, 3, 4 etc. Remember, when you arm unit #1 units 2, 3, 4 etc. will respond to the same command if they are within range.

If you do not see your question or problem listed here, our Customer Service staff is waiting to assist you.

If you have lost your transmitter or just need an extra one, check your Installation and Operating Guide for instructions.

Yes, we will need to verify if you have a factory keyless transmitter remote or a aftermarket transmitter remote.

Replacement remote controls can be purchased for $15 from Curtis International. Please mail a certified check or money order (payable to Curtis International) to 315 Attwell Drive, Etobicoke, Ontario, M9W 5C1, ATTN: Customer Service Department. Make sure to include your name, complete mailing address, phone number with area code, model number of the unit and part required.

To purchase an extra REMOTE CONTROL contact DIRECT WHOLESALE at 1-800-659-0764, have the Installation Manual along with the Model number for your unit when ordering a new Remote Control.

A You can control direction - forward - reverse - left - right. Speed - faster - speed slower. Stop. This brand new remote control transmitter has been designed from scratch and is the most sophisticated remote control available

Garador stock all current Garador Controll-A-Door Remotes as well as a range of remotes from obsolete autos; please refer to automatic accessory page.

Yes. A replacement remote must be properly trained to your vehicle (see vehicle manual) and then it can also work with AutoWindow. Only the remotes that match your vehicle will work for AutoWindow commands.

You can replace the old or lost transmitter remote with a new one Or, you may want to purchase you a new alarm system.

Currently, no Do-It-Yourself unit has a second channel output capable of connecting to a remote starter. If you wish to use an alarm to control your starter, you would need to upgrade to a "Pro-Series" system. Please contact "customer service" for more details.

To disable the security system in case of emergency, follow the instructions in your product's owners manual for Service/Valet Mode. Yes, the remote control's code can be erased from system's memory for security reasons. Your authorized dealer can access this feature and eliminate the lost transmitters from operating your vehicle. Please contact your dealer to perform this operation.

Answer: You need to earase all existing remote controls out of your receiver. Check Lock Switch on Wall Console and apply Lock Switch in this situation. Question: What wire size do you use for each door button???? what gauge and conductor size???? Please respond as I wish to install behind sheetrock. thank you John. Answer: 22 gauge would be the minimum. We recommend running 4 wire thermostat, the wires are protected and a second pair is available for back up.

Yes, you can order an additional remote either online , by phone, or mail. Click here for more information.

Yes. The output signals can be configured in a variety of ways to interface with your standard controls. You will want to provide for use of the sensor health, however, as well as the temperature signal.

All of the Do-It-Yourself units are rated 127db (+/-3%) at 1 meter. Each unit is tested on the production line for proper volume before they are shipped.

Adjusting sensitivity on any of the Do-It-Yourself units is done in the same manner. Disarm the alarm, then press and hold button #3 (Finder) until the alarm responds with three chirps (non-talking models) or "Please adjust sensor now" (talking models). Simply hit the vehicle, open handed, above the alarm to adjust.

This Yellow wire is the unit's antenna. This receives the signal from the transmitter. Make sure that you DO NOT connect this directly to any metal or to electrical wiring under the hood.

Check the I.C. CHIP on the CIRCUIT BOAD of the NEW TRANSMITTER to see if it HAS the same NUMBER of LEGS as your WORKING TRANSMITTER.

Yes. The stays, or the plastic strips that prevent the crate and the run from collapsing while in use are available through the Order Form. For all other parts, call or write for exact figures.

No. We only place transmitters on dementia victims and special needs kids. We never put transmitters on "normal" kids or adults. We don't believe public safety agencies should become a babysitting service.

There are (2) two types of remotes, a NON-PTC or fixed code, and a PTC or Rolling Code, all Remotes look the same, but will not work because you got wrong type of Remote for your unit.

To get the remote control back, log back in to ShawOnDemand.ca, click MY ORDERS, then click the movie you’d like to control. This occurs because all times shown on the Web site are in Mountain Time. If you are in the Pacific Time zone, programs will expire an hour before the expiry time shown. Nevertheless, you still have the same amount of time to view the movie (usually 24 hours) as would a viewer in the Mountain Time zone. Your viewing time starts when you order the selection.

You may purchase an original OEM Apex remote control from Customer Service by calling 866-427-3946 or emailing us at customerservice@apexdigitalinc.com Or you could ask your Local retailer about a "Learning" Universal remote control that does no require special codes.

You must wait at least 1 minute or longer after Arming before you open the door (Dome Light Must turn ON) the vehicle to test the Alarm System.

If you download the 'Batch file to turn on the MediaMVP user interface on your PC', located here in the MediaMVP support page, you will be able to control the MediaMVP from the host PC without using the remote. This batch file will turn on the MediaMVP user interface on your PC. Once turned on, the Host PC's Monitor will display a mirror of what you see on your TV set with the MediaMVP.