Yes, this can be done by simply using remote transmitter #1 and by simply connecting power to each unit and using remote transmitter #1 to initiate the unit. This will let transmitter #1 operate units 2, 3, 4 etc. Remember, when you arm unit #1 units 2, 3, 4 etc. will respond to the same command if they are within range.

To purchase an extra REMOTE CONTROL contact DIRECT WHOLESALE at 1-800-659-0764, have the Installation Manual along with the Model number for your unit when ordering a new Remote Control.

Yes, monitoring is definitely available for DIY installed systems. There are many companies out there that will provide alarm monitoring services. Of course, monitoring is not always necessary. Some people feel safe enough that a siren is enough to scare off any intruder. Others aren't comfortable unless they know that the police will show up at any occurance.

If you have lost your transmitter or just need an extra one, check your Installation and Operating Guide for instructions.

Yes. The output signals can be configured in a variety of ways to interface with your standard controls. You will want to provide for use of the sensor health, however, as well as the temperature signal.

All of the Do-It-Yourself units are rated 127db (+/-3%) at 1 meter. Each unit is tested on the production line for proper volume before they are shipped.

Adjusting sensitivity on any of the Do-It-Yourself units is done in the same manner. Disarm the alarm, then press and hold button #3 (Finder) until the alarm responds with three chirps (non-talking models) or "Please adjust sensor now" (talking models). Simply hit the vehicle, open handed, above the alarm to adjust.

This Yellow wire is the unit's antenna. This receives the signal from the transmitter. Make sure that you DO NOT connect this directly to any metal or to electrical wiring under the hood.

No. We only place transmitters on dementia victims and special needs kids. We never put transmitters on "normal" kids or adults. We don't believe public safety agencies should become a babysitting service.

Under the NCO, intruder alarm systems installed in any premises and vehicles shall not sound for more than 15 minutes and 5 minutes respectively after being triggered. In addition, the vehicle alarms shall not sound unless the vehicles are being tampered with. The controllers or registered owners have to ensure their intruder alarm systems comply with the requirements.

The same high standard GMP, (Good Manufacturing Practice) system which is regulated by the Government body, the Therapeutic Goods Administration (TGA).We follow this system to make our herbal medicines as well as in the manufacturing of our shampoos. We believe what you use on the outside of your body is just as important as what goes into it.

Kaleidescape provides dealers with control modules and touch panel templates suitable for a variety of control devices, using both RS-232 and TCP/IP. These include modules and sample code for Crestron 2-Series Processors and templates for the wide variety of Crestron touch panels and keypads and a module and sample code for AMX NetLinx Processors and templates for the wide variety of AMX touch panels.

You can have as many as you require up to six. There is an additional charge per transmitter, but the monitoring fee remains the same.

You must wait at least 1 minute or longer after Arming before you open the door (Dome Light Must turn ON) the vehicle to test the Alarm System.

Connect a normally closed relay across the Paging Inputs (plus [+] and minus [-]) so they are shorted together. When an alarm condition exists and the coil becomes energized, the contacts open and the short is removed. The Paging Input Detect Threshold must be adjusted such that the noise floor is sufficient to trigger a paging condition and enable ducking, (i.e.

A You can control direction - forward - reverse - left - right. Speed - faster - speed slower. Stop. This brand new remote control transmitter has been designed from scratch and is the most sophisticated remote control available

No...a simple answer to a complex question. We certainly understand the concept and the interest but we simply feel that in the long run, a simple layering approach gives you more flexibility. We learned a long time ago that anything that snaps off or on...or zips in and out...can a.) become unsnapped or unzipped and be lost or left behind or somehow misplaced. b.) the attachment mechanism can become worn or damaged and no longer function..

Absolutely not, without grounding consequences! In addition to needing a 6-wire modular wye connection, the transformer center tap has to be lifted on all but one of the pieces being powered. And with all that nuisance you are restricted to using only balanced wiring. The better choice is to use individual power supplies for each product.

The pack includes the balloons, the ribbon and the helium cylinder and nozzle. They are extremely easy to use, we show you how everything works when you collect the pack from us, or on delivery. We will also supply an instruction sheet with tips on how to get the most from your pack.

site map | home | little giant ladders | contact | faq | links | home improvement | policies| view cart

If the alarm goes off into full alarm 45 seconds after arming, this is telling you that the current signal of the alarm has been activated. If you have a cell phone, radar detector or aftermarket amplifiers installed in the vehicle, these units pull enough current even when turned off to activate the system. You can disconnect these units from power or turn off the current sensing on the unit. No, each unit is individually coded and has its own unique code number.

Yes, but you will notice that the alarm will have less sensitivity to impact on the vehicle that it would if it were mounted directly to the body itself.

These units are designed to be installed on metal-bodied Vehicles only. In some cases you should be able to mount this unit as long as it is grounded to the metal frame.

If you have tried moving the YELLOW ANTENNA wire in different directions under the Hood and cannot get the RANGE on the unit to improve, there may be a problem in the RF Section of the unit and it will need to be serviced.

This is done through a simple adjustment of the shock sensor. Disarm the alarm and press and hold the Finder button until the alarm says "Please adjust sensor now". Hit the vehicle, open handed, directly above the alarm. The alarm will respond by saying "Thank you". Next, arm the alarm and wait approximately twenty seconds. Now hit the vehicle, open handed, directly above the alarm. Now it will respond by saying "Please move away from he vehicle". The unit is now adjusted properly.

Currently, no Do-It-Yourself unit has a second channel output capable of connecting to a remote starter. If you wish to use an alarm to control your starter, you would need to upgrade to a "Pro-Series" system. Please contact "customer service" for more details.

The alarm's microprocessor is capable of sensing current change through the battery voltage. When the door is opened and the dome light is turned on, the microprocessor notices this change in the current status, activating the alarm.

The Warn Away responds only when a direct impact is applied to the body. A harder impact after this initial Warn-Away will set the alarm off in full alarm. Make sure the unit is securely mounted with all three screws to the metal body of the vehicle. Also make sure the black wire from the unit is attached to the bracket bolt. If this is all in place, check the white fuse holder and make sure the red power clip is connected firmly to the (+) positive side of the battery.

First method is by orienting solar panels to the position of the sun in the winter. That means that the angle of the sun is well off the summer position. Second method is by switching operation to domestic hot water only. A mechanical heat dump can also be used. Home | Site Map | About Radiantec | Why Radiant Heat | Systems | Energy Efficiency | Prices | Contact Us | Solar Energy

With a stereo setup, you use the normal feedback pedal (or knob) on the master, and have the master send continous controllers to the slave for its feedback. Since you already have them connected with midi for stereo, this is pretty easy. Fewer cables on the floor, too. This is the preferred way, since both the pedal and the feedback knob are controlling both units. If you are still using the old version 3.