The purchase of a CD recorder often results in what used to be an unusual situation: a machine with two CD-ROM drives in it. This leads to a number of interesting phenomena, usually having to do with poorly-written software that can't figure out which CD-ROM drive it's supposed to use. CD-ROM drives are typically connected to a sound card via a small cable (a couple of wires twisted together, ending in small molex connectors).

Some manufacturers make special grpahcis cards for PCs which allow PC to be succesfully used with fixed frequency monitors. Fixed Frequency Video FAQ at http://www.devo.com/video/ has more information on those cards which make is possible to use fixed frequency monitor as general purpose PC monitor.

In the list you get, click on "Sound, view and game controllers". If you don't see anything related to SOUND, click on "Refresh". The detection will start. If you still don't get anything related to sound, Bad luck... : (. You don't have it.

Yes, PC’s with a PCI bus on their motherboards can take advantage of Ultra 2 SCSI (LVD) drives. You need a PC Ultra 2 SCSI controller to connect the drive. The data Xfer rate of a disk drive is one important parameter in the overall storage subsystem’s performance, but the data bus (50 Mhz, 66 Mhz, 100 Mhz), carries the data from the drive to the CPU. Microprocessor clock speed , SCSI controller support of a particular drive interface, Ultra SCSI, Ultra 2 SCSI etc.

The microphone jacks of sound cards are generally equipped with T-feed, as with MD recorders. Therefore, OKM microphones will also work with sound cards. The adapter only needs to be equipped with a 3.5 mm coupling on 2 x chinch in order to be connected to all Line-In jacks on a home stereo system. The adapter can be run on a power supply instead of with the battery. In order to do this, just remove the battery, and connect 6 - 10 V power (banana clamps) to the battery springs.

Call the automated line at 877-807-4646 with your 12-digit order number, the PC Card wireless phone number, and the last 4 digits of your Social Security Number. Try running Activation again through the VZAccess Manager Options menu. Go to Options > Activation... Try running the Setup Wizard again through VZAccess Manager Options menu. Go to Options > Run Wizard...

Lola uses either a 20 foot cable or a 2.4GHz wireless transmitter and receiver to connect your PC with your TV and Sound System. If your computer is located less than 20 feet from your TV and Sound System, the direct wired option may be best for you. When your computer is located in a different room or on a different floor, the wireless option is the way to go.

It is possible to damage equipments when playing with PC vidoe hardware and workstation monitorts. If the monitor has standard video inputs, is workign properly, cable is properly constructed and everything is connected to properly grounded power outlet then the risk of damaging the graphics card is minimal. Some monitors can be damaged by sending wrong frequencies to them, so be sure that you send right frequencies to monitor.

With the current sound driver it's possible to have several SoundBlaster, SoundBlaster/Pro, SoundBlaster16, MPU-401 or MSS cards at the same time on the system. Installing two SoundBlasters is possible but requires defining the macros SB2_BASE, SB2_IRQ, SB2_DMA and (in some cases) SB2_DMA2 by editing local.h manually. It's also possible to have a SoundBlaster at the same time as a PAS16. With the 2.0 and newer kernels that configure sound using make config, instead of local.

No. The sound is an essential part of the game, and ST will refuse to run without sound support as described in 2.1.

The SignaLink SL-1 and SL-1+ only pass audio signals to and from the sound card, so they will work with ANY sound card that has a microphone input and a speaker output. The SignaLink Model SL-1+ also works sound card Line Input and Line Output jacks for greater flexibility. What you should really be asking is if the software will work with your computer and sound card.

We have discovered that some are better than others, though. If you seem to be getting MIDI data errors, try using a different sound card. Use a sound card or mainboard with proven Windows XP sound and MIDI drivers which are fully 48kHz sample rate compatible. The Creative Sound Blaster PCI 16 card is acceptable.

Florian Xaver postet a list of intersting DOS network links to the FreeDOS mailing list: http://www.freedos.org/freedos/news/technote/157.html. Thanks a lot!

You can connect a theoretical maximum of 127 USB devices to your computer. However, it may not be practical to connect more than 5 Flash drives at a time to your computer.

No, Alvarion does not manufacture an Electro-magnetic Interference filter for the CAT-5 ethernet cable. We recommend that the installer ground the shield of the cable at the building entry point as required by the local electrical codes. Alvarion does not have a lightning protection unit designed to protect the outdoor DS.11 products. Alvarion does recommend that the shield of the CAT-5 cable be grounded at the location the cable enters the building, as per your local electrical code.

Yes, the 802.11b PC Card can connect to an 802.11g Access Point. The G Access Point may need to be setup to a b/g mixed mode.

Yes “ When Cinergi sends you a modem; you will have a choice of selecting an Ethernet or USB connection. We would normally recommend an Ethernet connection if you have the card in your PC as the installation process is even easier and higher speeds can be obtained.

Thanks to John Mc Donagh aka Nascent Virion for a list of what bands he though typified the Gothic sound. Some may disagree, but this is a rather decent representaion of GENERAL catagories. Clan of Xymox (Synth, almost dancey) * Southern Death Cult (SDC) later split in all directions. Only SDC are condsidered properly Gothic. However many of Southern Death Cult's Goth followers remained true even when they entered their 'The Cult' glam metal phase.

You should connect the speaker output of the sound card to the microphone input of the modem with a 3.5 mm double mini jack stereo cable. You may use an output splitter on the sound card, which enables you to maintain the current speaker connection along with the new connection. Refer to the Help for more details.

Call the automated line at 877-807-4646 with your 12-digit order number, the device wireless phone number, and the last 4 digits of your Social Security Number. Try running Activation again through the VZAccess Manager Options menu. Go to Options > Activation... Try running the Setup Wizard again through VZAccess Manager Options menu. Go to Options > Run Wizard...

Answer: It has been report that this problem occurs when you format the card using your PC, rather than your N-Gage. So as a rule of thumb always format the memory cards with you N-Gage only. A possible solution is to format the card in a card reader connected to the computer, and formatting the card using the FAT 16 file system should work. This should remove any residual corrupted files, then you can format it again in the N-gage in order to get the correct file structure.

Digicanon has an uploader for the A610 on his page which you can use to upload the firmware files to the A610 without a card reader. This uploader may work also for other camera models, I've used it for A620. There is a textfile named "FirmInfo.txt". It contains this text: "[Firmware File Name]". Just change the name below it into the filename you want to upload. Then save the text file and start the UploadFirmware.exe. You have to do this two times: 1x for PS.FIR and 1x for DISKBOOT.BIN.

The course has the capabilities of displaying the audio as text. Simply click the CC button on the bottom left hand corner to display the text.

Yes, currently two we know of two commercially available systems.– SpectSoft, and Linux Media Arts.

You connect to network drives using Windows NT Explorer. Once there, from the "Tools" menu choose "Map Network Drive". When the "Map Network Drive" window comes up, select to which drive you want to connect and check the "Reconnect at Logon" checkbox; this way, you can always access that drive without having to repeat the process every time you log on.

This feature can be set up in the "Standard CMOS Setup Menu". For example, allow DOS/Windows 3.1 to operate the primary master hard disk drive and Windows 95 to operate the primary slave hard disk drive. Given that the system uses the primary master drive as it's default setup drive, you can change to the slave drive by setting "NONE" for the Primary/Master and "Auto" for the Primary/Slave in the Standard CMOS Setup Menu.

It is possible to daisy chain up to four FireWire drives to FireStore simultaneously. Drives can be unplugged or plugged in at any time. All drives are accessible from FireStore. It is possible to power one drive via FireStore's FireWire bus (if the drive as able to receive bus power “ check your drive owner's manual for more information). Additional external power may be required in order to power additional drives.

The next best thing is to post it to alt.binaries.gothic and post ONE message to alt.gothic saying that you have done so - it's a good idea to include the message-id of your binary in the advertising post to alt.gothic. Please read the alt.binaries.gothic FAQ before posting anything there. Its URL is http://www.zenweb.com/pan/panstuff/abgfaq.htm

If you are having difficulty hearing or you can not be heard, please check that your Microphone and Speakers are plugged in and operational. You may also adjust the volume settings on your PC-to-Phone by sliding the controls for the speaker and microphone icons towards the right to increase, or towards the left to decrease the sound level. If the speaker setting is on Mute, you will not be able to hear the other party.

Verify that the speakers are plugged into the line “out” or “spkr” port of the sound card. Verify the transformer for the speaker is plugged into an electrical outlet on one end and into the speakers on the other end. Check the mixer settings. Is mute selected or are the volume settings too low? Increase the master volume setting. If the sound card has a “diagnose” file on the installation disk, use this diagnose utility to check the sound card.