Can I install standard weight tile on my existing home or do I have to use lightweight?
Ask Wes : Frequently Asked QuestionsThat would depend on many factors. The biggest concerns are the unsupported span of the rafters and the size of the window and door headers. In many areas where snow load or wind load have already been designed into the structure the additional weight between standard and lightweight roof tile is within the tolerances built into the house. However, if your reroofing project requires lightweight roof tile, Westile offers FeatherStone lightweight roof tile in Colorado.
Related QuestionsCan I install ceramic tile over lightweight concrete or gypcrete?
Port St. Lucie, Florida Tile and Marble Contractor: Chris Bo...No, tile installation is not recommended over gypsum products. The moisture in the setting materials will deteriorate the gypsum cement.
Related QuestionsCan I install cork tile over an existing ceramic tile floor?
Cork Flooring Frequently Asked Questions | DuroDesignYou first need to flatten the floor with a skim coat of a Portland cement based patching compound. Or, you can simply install a floating clic cork floor directly over the existing tile.
Related Questionscan I install insulation in my existing home?
faq'sExisting homes can easily have insulation installed in most ceilings and under timber floors, space permitting. However, walls and vaulted ceilings can only be insulated during the recladding or replastering process.
Related QuestionsCan I install this in my existing home?
Cortexa TechnologyWhile it is always easier to install these systems in new construction environments, it is very possible to install the system in an existing home. All homes are different, and the degree of difficulty is dependent on what sub-systems you intend to automate, and the layout of your home.
Related QuestionsCan I use mastic to install floor tile?
Design Stone Gallery - FAQIt is preferred to use a thinset mortar for floors, but in residential use, mastic can be used with tile up to 6" x 6" in size on floors.
Related QuestionsPort St. Lucie, Florida Tile and Marble Contractor: Chris Bo...It is preferred to use a thin set mortar for floors, but in residential use, you can use mastic with tile up to 6x6 on floors. Of you are installing tile in an area that is going to be exposed to water conditions, use a mastic that is water-proof so that it will hold up well. This is very important. If you are applying floor tile in areas not exposed to water you can use a mastic that is not water-proof. Epoxy adhesives are also available but their drying times can be difficult to control.Related Questions
Can tile be installed over lightweight concrete or gypcrete?
Design Stone Gallery - FAQIt is not recommended to install tile over gypsum products. The moisture in the setting materials has a tendency to deteriorate the gypsum cement.
Related QuestionsCan I install floor tile heating under existing tiled floors?
FLOORSUREUnfortunately not. The installation of tile heating can only be done before the tiles are laid. If however you have purchased a new existing home without tile heating, you can have a carpet heater installed under a loose lay rug to negate the problem.
Related QuestionsHow much weight should I use?
Frequently asked questionsHyperStrike recommends performing each set with a weight that allows you to perform the suggested number of reps using proper technique. That means you may initially need to try several different weights before you find the right one. To see results you need to push yourself. Your muscles will adapt very quickly and if you use the same weight/load over and over again you will not progress.
Related QuestionsHow do I install Perl on systems that do not have it as standard?
WebminYou need to download and compile the latest Perl source from http://www.cpan.org/src/stable.tar.gz. Or if you have Solaris or HPUX you can download pre-built packages that avoid the need to compile Perl yourself.
Related QuestionsCan I use Villaboard® Lining over an existing floor and tile over it?
FAQs | James HardieAnswer: No, Villaboard® cannot be used on floors. Tile and Slate Underlay is the product to use for this application.
Related QuestionsCan I install Enviroshake® over my existing shingles?
Enviroshake - Manufacturers of environmentally friendly comp...Different jurisdictions have different code regulations but generally speaking, Enviroshake® can be installed over one layer of existing asphalt shingles, provided the roof is structurally sound underneath. There is considerable cost savings since there would be no additional cost for removal and disposal of the shingles. There are considerable environmental benefits to this as well because the old shingles need not be put in a landfill. No.
Related QuestionsI like to do it myself. Can I install my own tile roof?
Hanson.biz : Hanson Roof TileBecause tile is a unique product, it takes a craftsman to install a tile roof properly. Professional roofing contractors install over 96% of all tile roofs. A handy person may be able to lay field tile without much trouble, but installing underlayment, battens, flashings for valleys, chimneys, solar panels and skylights and cutting the tiles along hips and valleys are more complicated tasks. We recommend using an installation professional to properly install your tile roof.
Related QuestionsCan you install ceramic tile over wood?
CTaSC: Installation FAQ QuestionsLayout - My husband is having trouble with the layout/cuts in the ceramic tile for our tub/shower area. There is an uncentered window in the primary wall. He keeps saying "no matter how I figure it, I still end up with 1/2" gap at the top of wall". Is there any way you can tell him what he's doing wrong? Thanks SOOO MUCH! Exterior Chimney - Do you have any information on tiling the exterior of a stucco chimney? Below freezing in winter.
Related QuestionsCan I use mastic to install glass mosaic tile?
Frequently Asked QuestionsMastic is not recommended for installation of glass mosaic tile, particularly in wet areas such as showers. Bond strengths are lower than those of recommended setting materials. Mastic does not properly cure when used with impervious materials such as glass and may yellow behind clear or translucent tile. Yes. Our glass tile can be installed on the outside of a fireplace surround. A setting material company should be consulted, for advice about which tile setting material to use. No.
Related QuestionsCan I use a nail gun to install the Ezi-Grid® Tile Underlay sheets?
FAQs | James HardieAnswer: No, the nail is a 2.5 x 25mm Underlay Nail, which has been specifically designed for this application.
Related QuestionsCan I use mastic to install ceramic floor tile?
Caribbean Tile and Stone - || FAQ About Tiles ||No. Mastic is best used for wall tile, especially in high-humidity areas. For most floor installation, we recommend latex thinset.
Related QuestionsCan you tile over existing tiles?
WRS Contracts - Professional Ceramic Tiling ContractorsYes, as long as the existing tiles are firm and secure and are able to support the weight of the new tiles.
Related QuestionsTile New ZealandYes, providing the existing tiles are solid and fully adhered to the substrate. The existing tile surface should be adequately cleaned and in most cases â??primedâ?? ready for tiling over. The new tiles can then be laid over the existing tiles. There are flexible cement based adhesives which are manufactured for this purpose.Related Questions
Can you match an existing tile?
Norton TileGenerally speaking, no. It is very difficult to get an exact match because the appearance of a tile depends on many factors - the clay, glazes, method of firing and, of course, its age. The time and effort required to experiment on achieving a match makes the cost prohibitive without any guarantee of success.
Related QuestionsWhat is the difference between lightweight, medium-weight and normal-weight blocks?
Verastone Ground Face Masonry Units | Trenwyth Industries | ...ASTM C90 specification for load-bearing concrete masonry units defines lightweight as concrete less than 105 lbs per cu. ft., mediumweight as concrete between 105 and 125 Ibs per cu. ft. and normal weight as concrete of 125 lbs per cu. ft. or more. The aggregate used to make lightweight blocks is usually expanded shale, expanded clay, pumice or some similar type of open-cell material. By its nature such aggregate is porous and will allow some moisture penetration.
Related QuestionsCan I install floor tile heating myself?
FLOORSUREWe would prefer that you did not. Floor heating systems are professionally installed through our trained personnel.
Related QuestionsWHO WILL INSTALL MY STONE AND TILE?
Business Opportunity offered by Olde World stone & Tile Manu...Unless you are already in the installation business, and are a qualified installer, we suggest that you do not install the stone or tile yourself. You will be busy enough and making enough money operating the manufacturing end of the business, not to get into installations. Our manual has a section that teaches you the basics of installation so you have a working knowledge of it..
Related QuestionsCan you install wall tile on the floor?
Caribbean Tile and Stone - || FAQ About Tiles ||No. Wall tile has a lower breaking strength than floor tile. By installing wall tile on floors, you run the risk of the tile cracking or breaking over time.
Related QuestionsCan you install ceramic tile outdoors?
Caribbean Tile and Stone - || FAQ About Tiles ||Yes. However, we recommend unglazed, frost proof tiles for outdoor use. Look for tiles with absorption rates of 0.5% or less.
Related QuestionsCan I use the Weight Loss Software Food And Exercise Diary on my home computer and work computer?
Food And Exercise Diary for Windows | Calorie Counter | Food...Yes. One license allows you to install the software on both of your home computer and your work computer.
Related QuestionsHow do I install gems in a non-standard location, such as my home directory?
RubyGems Frequently Asked QuestionsYou have to redefine the location of the GEM_HOME variable and add the paths to the gem repositories in the RUBYLIB variable before launching the installation into a custom directory. Here is a shell script that runs in the rubygems distribution directory to install into /home/user : PREFIX=$HOME export GEM_HOME=$PREFIX/lib/ruby/gems/1.8 export RUBYLIB=$PREFIX/lib/ruby:$PREFIX/lib/site_ruby/1.8 ruby setup.
Related Questions