No. You can only apply a template valid for an access point with an 802.11g radio to an access point with an 802.11g radio. No. You can only apply a template valid for a 1310 wireless bride in bridge mode, to a 1310 wireless bridge in bridge mode.

Startup configuration is used right after a device (access point) reboots. It requires DHCP server to be properly set up to allow the access point to pick its startup configuration from WLSE. For this to work, you must set up the following: a. Enter the <IP address of the WLSE> in the Boot Server Host Name field (option number 066) on the DHCP server. For additional information, or for information about configuring a router as a DHCP server, see the online help.

This problem USUALLY means that your IFS Home Directory is over its quota. You can check this with the command: If you're "Used" portion is more than your "Quota" portion, then you are over your quota. You'll either have to make your quota larger ('lynx http://www.ifs.umich.edu/~ifs'), or delete some files to fix the problem.

Yes. The default settings (color, width, equation box etc.) are coded in the file fitparam.m. So you may create a copy of this file with your own settings, and you just have to rename the settings file you want to use fitparam.m.

Currently, the only way to save the configuration options in VLC is through the preferences menu in one of the graphical user interface plugins.

If you chose to save a configuration, it will be saved for 20 days. At any time during those 20 days, you can log back in using your email address and retrieve your saved configurations. You can continue to customize the configuration and save it as many times as necessary. Once you are satisfied with your configuration, you can place your order for your customised dedicated server.

To reconfigure the NVRAM, you first erase the Cisco 675 or 678 modem configuration and then reset the modem.

When zsh starts up, there are four files you can change which it will run under various circumstances: .zshenv, .zprofile, .zshrc and .zlogin. They are usually in your home directory, but the variable $ZDOTDIR may be set to alter that. Here are a few simple hints about how to use them.

Step 1: Choose Configure Settings from the Configure menu of the Image Viewer. This presents a configuration pane. Step 2: Click the Export Configuration button on any of the configuration panes. This presents a popup dialog. Step 3: Select the filename and indicate whether the blob table configuration and/or the color map are to be included.

Maybe you have a config.reg file in the Salamander's directory (the directory with salamand.exe), so a configuration is loaded from this file whenever you run Salamander. If you remove this file (or rename it), save will work as expected.

Yes. Your team's results can be managed centrally at the package level in any of today's popular configuration management systems.

In the RLS configuration file ($GLOBUS_LOCATION/etc/globus-rls-server.conf), find the rli_bloomfilter_dir property. It should be commented out (remove the # at the beginning of the line) and have a value of none. Create an entry in the file as: rli_bloomfilter_dir <path to a valid dir> Next time you restart the RLI, it will save Bloom filters from LRCs and upon subsequent restarts it will load the Bloom filters from the specified directory.

You can use any unique name in the configuration file for each screen but it's easiest to use the hostname of the computer. That's the computer name not including the domain. For example, a computer with the fully qualified domain name xyz.foo.com has the hostname xyz. There should also be an alias for xyz to xyz.foo.com. If you don't use the computer's hostname, you have to tell synergy the name of the screen using a command line option, or the startup dialog on Windows.

If your configuration has somehow been screwed up, you can get back the standard configuration with the command: If you only need a specific configuration file, you can limit it to that file by specifying the file on the command line: This is usually necessary because someone deleted the files by mistake, or because someone has old files, and they need to be updated. The files affected are: .cshrc, .login, .logout, .xsession, .Xresources, .mwmrc, .principals, .profile, .tvtwmrc, .twmrc, .zephyr.

The full error message resembles the following: FW ERROR 1-01: NVRAM SANITY FAILURE DEFAULT VALUES ASSUMED IF REPEATED, CHECK THE BATTERY The 3B2 stores information such as the time of day clock and machine name in non-volatile memory. The memory is backed up by a Lithium battery, that does die after a few years. The battery is normally located in the right side of the case, near the cards, and connected to the motherboard under the card in slot 2.

If you have a tftp server available, you can create a file on the server for your router to write to, and then use the write network command. From a typical unix system: mytftpserver$ touch /var/spool/tftpboot/myconfig mytftpserver$ chmod a+w /var/spool/tftpboot/myconfig myrouter#write net Remote host [10.7.0.63]? 10.7.0.2 Name of configuration file to write [myrouter-confg]? myconfig Write file foobar on host 10.7.0.

Where file.cfg is the name of the file to store your configuration in. You can view the name of the file that the router will boot from using the 'show config' command. Hello, I have an AR740 router with 2 default gateways (static) to 2 different ISP. The ip multipath routing works fine when connections with both ISPs are ok. But when one ISP goes down the router continues to use the failed default gteway.

To create a clonefile containing all the settings of the computer you want to copy, go into Setup Mode and click Export Clone File. By default this file will be named clonefci.bds which is the name needed by Full Control Internet's AutoUpdate processing. Usually this is done from the Remote Administration Manager, but it can also be done from an individual client computer.

CSG relies on the external (SMTP) mail server to send reports, logs, and notifications. If you do not require reports, logs, or other types of notification, just enter a random valid IP address.

There sure is! Right click on the tray icon and select properties. In the menu that opens, select the General Tab. Uncheck the box that says "Launch Main Window on Startup" and the Agent will start up minimized from now on.

Your Group directive (probably in conf/httpd.conf) needs to name a group that actually exists in the /etc/group file (or your system's equivalent). This problem is also frequently seen when a negative number is used in the Group directive (e.g., "Group #-1"). Using a group name -- not group number -- found in your system's group database should solve this problem in all cases.

A configuration is simply how Fretboard IQ refers to a particular fretboard diagram and all its associated options, like fret count, tuning, selections, string filters. Basically all the options that went into creating the unique fretboard diagram can be saved as a configuration for viewing later simply by selecting the configuration from the configuration list. You can name the diagrams anything you want as well as add comments about why the diagram is of interest.

Sometimes it's useful to have a dump of the NVRAM variables to show them other people for debugging. This can be done with: sort will sort the list alphabetically to make it easier to read. Use more to list the output page by page. You can also save the dump into a text file. Use > /tmp/nvram-dump.txt instead of more. Then SCP the file to another computer. NOTE: Do NOT post the dump directly into the IRC channel, for that use a pastebin service like pastebin.ca or pastebin.com.

Answer: The software video driver for the monitor is loading up. This is normal and is answered in the Power Macintosh 7200/9500 Read Me file. Answer: The Power Macintosh 7200 series computers originally shipped with QuickTime 2.0. and will benefit from the Tuner. If you have installed QuickTime 2.1, then you do not need to install the Apple Multimedia Tuner. Check the version of QuickTime installed to determine if you need the Tuner. We would recommend upgrading to QuickTime 2.

This is always a challenge, but there are plenty of resources to consult. A while back ComputerWorld Careers ran an article titled Digging Up Dirt on a Startup , that provides a good primer. I'd also advise searching the Press Pass for any mention of the firm. Try Lexis-Nexis, Factiva, and Business Source Premier first, and if you're researching a tech startup, be sure check out the various trade press search engines in the Press Pass.

For the Windows version, drag a copy of the desktop shortcut to Start Menu > Programs > Startup. For the Macintosh version, make an alias of the application (using Command-L) and drag it to the /Library/StartupItems folder.

Mostly this is a problem of Firefox itself and has nothing to do with AiOS. Please read this article at the knowledge base and follow the instructions.

Zone Alarm 5 is known to break Cygwin/X. As a result you'll see this line (or a similar) as last output in /tmp/XWin.log Rules = "xorg" Model = "pc101" Layout = "us" Variant = "(null)" Options = "(null)" Disabling Zone Alarm will not solve this problem. You can only uninstall Zone Alarm 5 and switch to an earlier version (4.5 is known to work) or use a different personal firewall. Another reason is /tmp mounted in textmode.