Q: Can I set up the OzLine unit for an outdoor application?
OzVisionA: Yes, but if you are going to use motion detectors, adjust the sensitivity to prevent false alarms.
Related QuestionsQ: Can I loop a DVR and an OzLine unit?
OzVisionA: Yes, you can loop from the DVR to the OzLine unit. If neither has looping, you can purchase four BNC-Ts and T-tap into the DVR. If you are using the 12CS, bring the cameras into the unit and then loop out to the DVR.
Related QuestionsQ: What do I do if the OzLine unit remains armed when the alarm panel is disarmed?
OzVisionA: Arm the panel, then have the central station dial in and program the day/night toggle option. Once this has been done, everything should work properly.
Related QuestionsQ: Can a US Robotics modem receive test signals from an OzLine unit?
OzVisionA: No. You will need to replace the US Robotics modem with any other type of modem because the chip set in the US Robotics model will not establish the handshake with the OzLine unit.
Related QuestionsQ: Can I dial in to the OzLine unit to view video after an alarm signal comes in?
OzVisionA: It is not part of the business model of a central station for an operator to dial in to the unit. This feature is intended mainly for end users and, if the end user desires, a central station supervisor.
Related QuestionsQ: How can I adjust an OzLine unit's scan time?
OzVisionA: Dial in to the unit and select "Tuning," then "Unit Power on Parameter." Under the "CCTV" tab, you can adjust camera and scan time. Click "Upload" to save the changes.
Related QuestionsQ: How do I adjust the ring count on an OzLine unit?
OzVisionA: Dial in to the unit and click "Tuning," then "Unit on Parameters," then "Modem." You can change the number of rings on the lower left of this page. Click "Upload" to save changes. Click "Upload" and save changes. A: This is not suggested, but you can share OzLine with a credit card machine, fax machine, etc., using a line sharing device. To do this, set the number of rings on the other device to four. Set the number of rings for the OzLine unit at 15.
Related QuestionsQ: How do I connect an OzLine unit to an alarm panel?
OzVisionWe recommend using the PGM outputs on the panel. The OzLine units require a dry momentary contact to trip an alarm.
Related QuestionsQ: How long does it take to download from the OzLine unit's buffer?
OzVisionA: Auto download takes time to download from the unit if the buffer size is set to high. It all depends on the phone line and frame rate.
Related QuestionsQ: Why does the connection to an OzLine unit drop after a few minutes?
OzVisionA: There may be static on the line. Changing the phone line should resolve the problem. If this does not work, make sure you have the correct power to the unit and verify that you are not using demo software, which disconnects after five minutes of use.
Related QuestionsWhat is an outdoor unit?
Tata Indicom VSAT ServicesThe outdoor unit (ODU) consists of a small parabolic antenna usually made of aluminium or metallized fiberglass, that can be mounted either on the roof, on the ground or on a wall. The antenna system comprises of a reflector, feed horn and a mount. It has a feed system to direct and receive the signal along with a transmitter and low noise converter to pick up the signal with minimal noise interference.
Related QuestionsWhen replacing the outdoor unit, should the indoor unit also be replaced?
Frequently Asked QuestionsAll outdoor cooling units are specifically designed to work with matched indoor units for optimum efficiency and performance. Air conditioner and heat pumps may "work" with other indoor units, but the result is a definite compromise in overall system performance. In recent years, indoor blower coil units have undergone numerous design advances - especially in the areas of air handling performance, filtering efficiency and operating sound levels.
Related QuestionsQ: Can the OzLine units be connected via DSL?
OzVisionA: Yes, you will need to use an analog filter to change the signal from digital to analog to be able to establish a dial-up connection. Note: The DSL modem must support protocol V120.
Related QuestionsQ: How do I use the OzLine for on-site viewing?
OzVisionA: You can do this through the video output onto a local monitor or you can set up a direct connection with a PC for local viewing.
Related QuestionsCan shrubs or flowers be planted around an outdoor unit?
Frequently Asked QuestionsYes. However, we recommend that plants be no closer than 18 inches (45 cm) to the unit. This allows for plenty of room for air circulation in and out of the unit. Without this room for air circulation, the unit could overheat, resulting in a premature need for service, excessive wear, excessive electrical consumption and possible compressor failure.
Related QuestionsShould my outdoor unit be covered in winter?
Atlanta Heating and Air - ACCUTEMP - Frequently Asked Questi...NO! Air conditioners are made to last for years in the outdoors. Atlanta's strange weather makes it nearly impossible to predict and if you forget to uncover it, you could cause serious damage. Heat pumps run nearly year round, and make no sense to try to cover them.
Related QuestionsShould I cover my outdoor unit in the winter?
Broomhall Brothers Mechanical Contractors — FAQ'sCovering the unit is not necessary. Air conditioners are manufactured to withstand all possible climate changes.
Related QuestionsPurvis Heating & CoolingFAQIt is not necessary to cover the unit. Air conditioners are manufactured to withstand all possible climate changes. In fact, rain helps keep your unit clean. Since heat pumps run all year long, they should never be covered.Related Questions
FAQCovering the unit is not necessary. Air conditioners are built to withstand a wide range of climate changes. Rain even helps keep your unit clean. Since heat pumps run all year long, they should not be covered.Related Questions
FAQThere is no need to cover your unit. Air conditioners are built to withstand all possible climate changes, from the cold of winter to the blazing heat of summer. -------[Back to Top of Page]-------Related Questions
Q: How Do I Install the Get Set desktop application?
WestJet Get Set ...Simply click on the “Download Get Set” button and choose “Save” when the dialog box pops up. Choose a location to save your Get Set desktop application (we suggest your MyDocuments Folder) and then click OK. Once the application has downloaded, click on the icon in the folder you saved it in to run it. Once it runs the first time, Get Set will always run each time your computer starts up.
Related QuestionsQ: How Do I Uninstall Get Set desktop application?
WestJet Get Set ...To manually uninstall Get Set you will need to delete the installation folder, Start Menu and Desktop shortcuts. To delete the installation folder, navigate to the folder "C:\Program Files" and delete the folder named "Get Set". To delete the shortcuts from the Start Menu, navigate to the folder "C:\Documents and Settings\User Name\Start Menu\Programs\" and delete the "Get Set" folder. To delete the Desktop shortcut, right click on the Get Set Desktop icon and select "Delete".
Related QuestionsHow do I set the unit to operate in Binary mode?
Technical SupportSimply hardwire connect the Memory Recall Port (MRP) terminals numbered 5, 6 and 8 to the COM terminal. This will enable the unit to accept binary memory recall input and yield 24 memories.
Related QuestionsQ: How many cameras can be used to transmit with the OzLine units?
OzVisionA: The OzLine series can transmit to 4 to 12 cameras, depending on the model. However, you will only be able to see one camera at a time with local viewing.
Related QuestionsQ: Can the OzLine units transmit a signal to a PC with a direct connection?
OzVisionA: No. They only transmit video to a receiving PC or the central station via POTS (phone line), cellular or IP. Check with your central station to see how they receive signals.
Related QuestionsQ: What is the recommended way to arm and disarm the OzLine units?
OzVisionThe central station must adjust the day/night switch key setting. Connect to the unit. Go to "Tuning," then "Unit Power on Parameter." Under the "Advanced" tab, select the "Day/Night Switch Key Mode." Click "Upload" to make the change. That way, if there is any power loss, the OzVision unit will remain in the state it was in prior to losing power, rather than resetting itself. Make sure the OzVision unit in always in an "Armed" state.
Related QuestionsQ: How does the video output work on the OzLine?
OzVisionA: The OzLine has a built-in switcher. You can adjust the dwell time and select which camera you would like to switch from the "CCTV" tab in the software that comes with the unit.
Related QuestionsQ: Is it possible to remotely arm or disarm OzLine units?
OzVisionA: Yes. Dial in to the unit. Once you have connected, you will see an icon that is light blue/teal with a yellow key in the middle. Once you select that, it will turn dark blue with a key in the middle. When the icon is dark blue, you will know the unit is armed.
Related Questions