A good rule of thumb is 1 kit (32oz.) will do a 32' boat up to 8 coats. The product is applied in THIN coats, thus a little goes a long way! (Back)

The liter makes enough pre-burnish for 51,000 square feet or it will dilute down to make 135 gallons of ready to use mopping detergent.

As mentioned above, when gelcoat ages the surface becomes microscopically pitted, thus reflecting light in different directions. This is why the surface looks dull. Poli Glow fills these pits and retards further oxidation by sealing the surface from the elements. In addition UV inhibitors are formulated into the product (sort of a sunscreen for gelcoat). (Back)

Remember, Poli Glow eliminates waxing once and for all. It would be self-defeating to apply wax over the Poli Glow surface, and possibly could dull your surface depending on the abrasive properties of the wax. (Back)

Arthritis is a term used to describe many types of inflammatory conditions of the joint, bone or cartilage. This condition limits range of motion and causes pain that can be treated with Flexstat.

The large bottle is for dealers who do a lot of OEM decal replacement. The 2 oz. version is more than sufficient to install your registration numbers, logo decals, racing numbers, backgrounds and other decals.

We don't recommend it. Poli Prep is specifically formulated to remove any oxidation and wax that may reside in your gelcoat. You wouldn't think of painting a dirty car, would you? (Back)

While Poli Glow will seal the gelcoat surface, thus reducing penetration of foreign substances, the Poli Glow surface can of course become dirty. Just wash with soap and water. (Back)

One device is adequate for the treatment of max. 150 cubic meters room.(about 450 sqft). However, it is recommended to use it close to you in the room

Generally speaking, for an adequate air exchange rate, you can expect up to 500 sq. ft. coverage for the SE400E, and around 700 sq. ft. for the SE800E. - based on moderate concentration levels w/ 8 ft. ceilings. Individual results will vary based on environmental variables. To find out how many of which air cleaner you need, try our air cleaner calculator in the Buyer's Guide.

I have just received my order of Poli Glow and am preparing to refinish my boat. The boat is currently out of the water for some repairs and a bottom job. I would prefer to do the deck and later do the topsides.

adult will find about four weeks' supply, and children, depending on weight, will find enough for two months. Fruit-Eze™ fruit blend stores at room temperature and will remain good for at least 18 months. (see question 1, above).

Absolutely! In the event you need to remove any "stickies" just use the Poli Prep to remove the Poli Glow in the area of interest, remove/replace and re-apply Poli Glow over the area. (Back)

The Poli Glow surface will reduce the effectiveness of molded "non-skid" if it fills in the voids that provide the traction. When traction is of significant importance: high foot traffic, competitive boating, and commercial applications, we recommend the use of our non-skid product Woody Wax Non-Skid Deck Wax on the deck. However, many of our customers (myself included) have used it with no problems on non-skid.

Very easy. 100 square meters is 1076 square feet. Surfaces are given in square meters, written m2 or m2.

a. Yes it is quick and easy, trace with the stylus pen around the area and the program calculates the square feet of any area, also trace along any straight or curved length and the program calculates the exact linear feet.

The Allergy Machine™, HealthMate™ and HealthMate+™ have 60 Sq. Ft. The HealthMate Jr™ Model has 30 Sq. Ft.

Truthfully, that can only be best done if the entire floor plan of the home, insulation value and needs are all considered. It is always best to speak with a dealer, tell them about your home, life style and describe what your goals are for heating with wood.

There are 43,560 square feet in one acre. Therefore, if the size of a property is 0.20 acre, then it would measure 8,712 square feet (43,560 x 0.20 = 8,712).

We go by unit price and not by square feet due to the fact that square footage is not accurate and often works out to be more expensive. If you have a lot of windows, we can offer a volume discount. Unit price varies depending on how many windows you do and what is involved.

The Ski Suites (1 - 2 people) are approximately 350 square feet. The One Bedroom condos (2 - 4 people) are approximately 525 square feet. The Two Bedroom condos (4 - 6 people) are approximately 825 - 1000 square feet.

The square footage given for each plan is based on heated floor space. This does not include decks, porches or garages. Due to varying methods of calculating the total square footage, it is recommended that final area calculations be done by you and your builder. The room dimensions given on the floor plans are rounded to the nearest inch. As you will see, it is not always possible to give specific room dimensions due to the open nature of some floor plans.

Depending upon the type of material and the accuracy of the rough grade provided the Laser Grader can grade up to 50,000 S.F. per day. Northeast Laser Grading offers high precision grading for supermarkets, warehouses, parking lots, athletic fields (football, baseball, soccer), tennis courts, horse arenas and more. Serving the northeast, including Maine, New Hampshire, Massachusetts, Vermont, Connecticut, Rhode Island, New York, Pennsylvania and more.

One of our sales representatives will come out to your house and measure. From the measurement they can let you know how much square footage is needed. If you want to know the exact formula, just ask... they will be happy to teach you. You may also draw a rough sketch with measurements and fax it to us. Just be sure to include your contact information.

Meter to feet Length ratio=3.3 (One meter equals 3.3 feet) Sq.meter to sq.feet area ratio= 10.76 (One square meter equals 10.76 square feet) In order to get the feet equivalent, you just have to multiply the meter amount with the length ratio (3.3) to get the amount of feet, or divide the feet amount by the length ratio to get the meter amount. For areas and spaces, just multiply the square meter amount with the area ratio (10.

Production often depends on the sewer section size, location and the proximity to one another. On an average day with good weather, we can treat approximately 6,500 feet.

Generally on a floor you should get about 250 to 500 square feet per set ( 2-five's of powder and 1-five of liquid.)