I seriously considered putting the UniDisk db-19 connector on the SVD - or more accurately, the dongle. However, I simply could not find an economical supply of them. It appears that the db-19 is a connector of the past. The 20-pin headers are far easier to come by, and quite a bit cheaper...and you all know my mantra relative to the SVD "the cheaper the better." However, it is a theoretically simple matter to connect the SVD to the UniDisk controller.

QKB15S Keyboard Controllers are powered by +12 VDC usually from a wall transformer. The Q101, Q103, and Q137 Power modules provide DC power via a 6 pin female connector. The voltages available are +15VDC, -15VDC, and +5VDC - all well regulated. The keyboard controller has it's own internal regulator and only needs about 9VDC - 18VDC at less than 50ma. So you can provide power to the keyboard by a short cable from one of the modules. When you turn your system off, the keyboard will also go off.

In brief, Windows supports many of the Apple "Postscript" laser printers; check the Windows' printer setup for a list of printers, then look for the "Apple" printers, for specific models. Non-Postscript printers include all of the Apple inkjet printers (all Stylewriters), and some of the oldest laser printers. Regarding impact or dot-matrix printers, you can with effort hook an Imagewriter or Imagewriter II to your Windows system via the SERIAL port; select the C.

Yes. Connect the power cable into the jack on the back of the serial cable connector that connects to the computer. Connect the power supply end to a power outlet or power strip.

If your TV set is HDCP enabled, you can connect your HDMI device to your DVI TV set by using a HDMI to DVI adapter. It is a small device that you can find in any Hi-fi or TV store. However, remember that sound will not be transported. You will need to use the audio output of your device and the audio input of your TV set. You can connect them together if you use a DVI to HDMI adapter. Please contact your Hi-fi or TV store for more information.

When a video AGP add-in card is used, the Intel Extreme Graphics controller is disabled and the AGP connector operates in AGP mode. When an ADD card is detected, the Intel Extreme Graphics controller is enabled and the AGP connector is configured for DVO mode.

All Twenty20 camera systems include a '3.5mm Mini-Jack' connector to plug into the A/V (Audio/Video) input on your recording device. The way to determine if you need a connector is if your A/V plug is different than the 3.5mm plug provided. Keep in mind that NO MATTER THE RECORDING DEVICE YOU MUST HAVE AN A/V (AUDIO/VIDEO) INPUT. Be sure to check the Twenty20 Compatibility Page to verify your camcorder is compatible.

You can modify an existing cable, or create a new cable with wires and a 2.5mm phone plug. You can buy a 2.5mm plug connector from Mouser. Here are the part numbers: The polarity is important! Our flash trigger output is a 2.5mm phone jack. The center conductor (tip) gets the positive trigger voltage, and the outer (shield) is ground. If you can rig this up to your electronic flash, it should work fine. If you are going to modify a cable, cut off the end that you are going to connect to the 2.

The controller connects to the port labelled 'RF 2' or 'RF out 2'. This port usually also has a label reading '9V DC 75mA'. Unfortunately none of our controllers will work with any of these boxes. The UK cable companies supply boxes that can only be controlled by infra-red.

Yes, multiple solar panels can be connected to the charge controller in parallel (â??+â?? to â??+â?? and â??-â?? to â??-â??). The current from each panel will combine to charge more quickly. The total sum of the rated panel currents cannot exceed the limit of the charge controller. The 7A controller can support up to 105W and the 30A controller can support up to 400W. Multiple controllers can be used for larger power demands.

The very short answer is: you can't do this easily. There are problems between the USB-to-serial stuff; problems with printer drivers; and problems with OS X (or OS 9, etc) not knowing about either. The G3's, G4's and iMacs do not have the old Apple "DIN-8" connector (serial Localtalk) for modems and printers. These later Macs either use USB or Ethernet. Regarding the DIN-8 and Appletalk, see a related FAQ question for a description of that port. I don't describe Ethernet or USB.

Apple Airports operate with the same 802.11-based technology as other types of routers in the marketplace. They also now are compatible with both Macintosh computer and PCs. Check with Apple for details on setup if you plan to install an Airport.

Yes. Our network is compatible with all computers which use the PPP protocol, including all Apple computers. Our technical support team is able to provide support for customers with Apple computers. We recommend that your Apple uses MacOS 8 or higher.

Connections to Apple Macintosh computers are still being investigated. Some users have reported limited success with Virtual PC and Pocketmac. However, at this time QEA cannot say for certain whether or not these products work.

Answer: The connector for this antenna is an F jack. There are two methods for connecting it to a scanner: You can use an RG-6 cable with an F plug on each end and then use the F to BNC adapter (Cat. No. 278-0251) between the cable and the scanner. You can use an RG-6 cable with an F plug on one end and a BNC plug on the other. We do not sell this cable pre-built.

Just pins 1 & 2 (and pins 3 & 4 for V1.1+ boards). Pins 5 & 6 control power from the optional pyro battery, and can be left open if you're only using one battery.

HD-15 to 13W3 video adapter is provided with the Sun XVR-500 graphics accelerator to connect directly to a 13W3 video cable.

Wire the DIN plug so that the conductors +V and 0V for d.c. or the Live and Neutral for a.c. are connected to the parallel terminals. Polarity must be observed when wiring to a d.c. plug fitted with an LED indicator. Also when fitting diode suppression to d.c. coils (banded end of the diode to +V). The earth conductor connects to the third terminal, this is essential for all unsafe voltages.

A "Connector" is an add-on link between an eCopy-enabled scanner or digital copier and a networked software application or service like e-mail, document management systems, fax servers, enterprise software applications, etc. It is a physical piece of software. A "Quick Connect" is a feature/function within eCopy ShareScan. You can configure "Quick Connect" in virtually unlimited ways using any number of scanning profiles.

Lumenera recommends an intermediate connector that has a variable input of 16 to 20 AWG such as the 2-Conductor Lighting Connector from Wago, Item #224-112 (www.wagocatalog.com). The DHCP fallback IP address is available on the camera if there is no DHCP server present. Add an IP address to your network connection that is compatible to the DHCP fallback (192.168.1.222) or the link-local (169.254.X.X) IP address.

No, the CPU Fan Connector must be connected to the AC4G Power and Control Unit as described in the AC4G Quick Start Guide and AC4G User's Manual, otherwise the computer will not function properly.

From a request from a major production boat company in 2005, all OceanLED lights are fitted with Plug & Play connectors from the world renowned connector manufacturer Deutsch. All connectors are IP68 rated and comply with ABYC regulations, E11. We also recommend a synthetic connector grease to maximise connector performance, check the accessories page for further details.

You may have established an Apple ID to make a purchase from the Apple Store, the iTunes store, to access the AppleCare Knowledge Base, or to register a new Apple Product. If you have a .Mac account, your .Mac login acts as an Apple ID as well. To create a new Apple ID, confirm that you have an Apple ID, or to retrieve a forgotten password visit: https://myinfo.apple.com/.

Very easy. The AX2550 will connect directly to two R/C radio channels for commanding each motor. One additional channel can also be connected to the controller to trigger on-off outputs for commanding accessories. The challenge with a large gas-powered vehicle is the force with which to activate the controls which far exceeds this of the heaviest-duty RC servos. This is particularly the case of the brake and steering activation.

The controller will connect to brushed DC motors. It is recommended to use permanent magnet (PM) motors.

Yes, you can, the A6 has analog CV inputs to the oscillators and filters, allowing you to connect some of your precious vintage controllers to the A6.

Any display you like ? this is a truly open system. Historically, we have seen more than a dozen types of Modbus displays connected to a VersaTRAK RTU or SixTRAK controller. Now with the upgrade to embedded LINUX, you can use any dumb display and generate messages from within the controller. Of course, you can use any graphic interface or HMI software. There are many of them to choose from (some of them are running Windows CE ? its perfectly compatible).

ANSWER: You can use a standard 9-pin serial cable to go from a computer to a LC unit without needing an adapter. However, if you'd like to use cat5/network cable then you would need one RJ45-to-DB9 female for the computer side and one RJ45-to-DB9 male adpater for the LC side. If you would like to connect more than one LC unit to the computer in this manner simply use a RJ45 splitter in the line to provide more connections.

Because we cannot use the DVI-D signal, we must use the component outputs. Your HD Set-top-box should output 1080i/720p/480p/480i through its component video cables. You can input component signals into your controller using Sync-on-Green with this cable.

Fortunately, adding a rain sensor is simple with Rain Bird controllers, even if the controller does not already have a sensor connection. Just follow these instructions. Cut the common wire near the controller. Connect one sensor wire from the rain sensor to the common wire connected to the controller. Connect the other sensor wire from the rain sensor to the common wire to the valves in the lawn area. In other words, the sensor simply becomes a section of the common wire.