Yes, when proper installation methods are followed. Exterior applications require special precautions and installation methods. Do not install floor tile on exterior walls unless the product specifically recommends this application.

No, we do not recommend doing this, as a wall is generally a P.E.I. 1 tile, that is it has a very low wearing and will not last very long.

Wall tiles are generally more porous, which helps with their adhesion to walls, the glaze is used more for the appearance, and is resistant to detergents etc. On the contrary, floor tiles have low porosity, with low to medium water absorption, which will give them better technical characteristics, as the glaze is more than the look, it is also used to prevent wear and promote scratch resistance.

Yes. If the old tiles are high-gloss, we recommend sanding them down first to increase bonding strength. Then use a high-strength latex thinset to install the new tile.

No. Wall tile has a lower breaking strength than floor tile. By installing wall tile on floors, you run the risk of the tile cracking or breaking over time.

For floor tile, multiply the length by the width to get the square footage needed. Then add ten percent for cuts. For walls, multiply the linear feet by how high you want the tile to go from the floor. For example: Your wall measures 40 linear feet and you want the tile to end 48 inches (4 feet) above the floor. 40 ft. x 4 ft. = 160 square feet

The lower course tile in a vertical wet area should be above the floor tile and there should be a joint there of 1/4" that is properly treated as a movement joint per TCA EJ171 filled with a proper sealant to meet ASTM C920 (silicone, urethane, polysulfide). Good Luck! There are epoxy adhesives that will allow you to bond ceramic tile directly to Formica, but that application is not recommended by industry standards. Of course if the Formica ever comes loose so does everything else.

Structural strength and resistance to abrasion. We will help you choose the perfect tile to use for your space. One example - we wouldn't advise Mexican hand-painted tiles for a shower, on account of the wider grouting required.

Our technicians do not install floor tile, but we can recommend and coordinate with tile contractors to give your bathroom a completely new look.

Typically the removal and disposal of that type of asbestos containing material is not regulated by EPA (even commercially) if it is in good condition. If the material can be taken up with no significant breakage, there is little risk for fiber release.

Your architect or contractor will be the best judge, but 35 kg per square metre is the prescribed limit for stud and plasterboard walls. We will advise you on the correct seal for any tile you choose. Surprisingly unglazed porcelain, especially if polished, requires sealing.

It's the newest style in wall decoration, molded and hand painted to create 2 dimensional hanging blocks. Instead of the motionless works of art like painting, these tiles can be displayed more creatively - they can be grouped en masse, in series or in checkerboard effect. You can change the patterns and arrangements as your mood suggests. They're transferable reasonably priced as well. It is a perfect gift and collectible item.

Yes you can tile over a painted wall, however there may be limitations. If it is a painted wall for a kitchen splash or a tub surround it should be fine unless it has many coats of paint on it. Concrete walls, the paint must be removed.

Yes, it is possible. However, there are some conditions which must be adhered to. Existing floors must be overlayed with at least WBP grade plywood. However, marine ply is best. It must have a minimum thickness 19mm, screwed down (not nailed) at 150mm centres. All timber surfaces should be primed on the reverse side and all edges. It is essential that one uses powdered adhesive with a latex additive when tiling onto plywood.

Ceramic tile in either glazed or unglazed form do not need to be sealed. These products are impervious to moisture and topical sealers will not properly adhere to them. Also, you can not change or alter the appearance or the sheen of a ceramic tile by adding a sealer. Therefore, a sealer in not recommended for glazed and unglazed surfaces.

Tile mosaics are a wonderful, lively addition that complements the appearance of your pool. They can be selected and ordered upon your visit to choose waterline tile.

We would prefer that you did not. Floor heating systems are professionally installed through our trained personnel.

Water and oil will bead up on your floor when sealed as recommended in our Installation Specification Guide. You need only mop it up with a sponge. For routine cleaning vacuum or sweep it, as you would any other natural stone floor or a wood floor. To wipe up, use a non-acid based cleaning product. Warm, soapy water is also fine. AquaMix makes a tile cleaning product, Concentrated Stone & Tile Cleaner, which can be used on your floor. Check their website at www.aquamix.

If the structure of the counter is strong enough to support the weight of the heavier floor tile, then this should be fine.

A tile, whether it be ceramic, porcelain or natural stone is usually a good retainer of heat. Therefore it can often be the warmest floor in your home or building. It depends on the air temperature under the floor and the exposure to sunlight etc. Under-floor heating is a good option to warm your floor but it???s real intention is to provide an efficient, effective heating solution that gives you comfort throughout your home, therefore fulfilling your complete heating requirement.

You can use a two part ???rubber based or latex modified??? flexible adhesive to tile directly onto the timber. (Ensure the product chosen is manufactured specifically for this purpose). The timber will need to be clean and stable. (You will need to confirm floor joists and spans will be acceptable). This option is best suited when there are concerns of adding extra height to the existing floor and/or in smaller areas not subject movement or high traffic.

No paint must be removed off of a concrete floor before tile can be applied. Removal of Paint can be done by scraping it or a shot blaster machine.

If the floor is cracked it is advisable to use an anti-fracture membrane, otherwise cracks may transmit through the tile. Also as stated in question #2 you cannot tile over a painted concrete floor.

Do not use household dust treatment chemicals on the tile. Use a vinyl floor cleaner and separate finish. Both must be water-based. Vacuums: Do not use a beater brush on a vinyl floor. Use the proper solid floor attachment for vacuuming. NO WAX! Do not wax a vinyl floor. All of our vinyl flooring contains a no-wax finish. The flooring is non-porous and will not absorb wax. It will build up and collect even more dirt.

Yes. However, tile will not bond directly to a wood floor. We recommend the following methods to prepare your wood floor for tile installation: Install Schluter Ditra, from Schluter Systems, with a latex thinset. Then install the tile using a non-latex thinset.

Wall tiles (because they are not intended to be load bearing) are typically thinner, lighter and softer than floor tiles. Wall tile glazes are not designed to handle the abrasive forces from foot traffic. Increasingly, floor tiles are being applied to walls and this is no problem so long as the walls are strong enough to support their weight and proper ceramic tile installation methods are used. However, it is not usual to recommend using wall tiles in floor applications.

In case of internal connections you can break and predispose pipes inside the wall in order to have a perfect aesthetic.

Most of our safes come with pre-drilled holes which will allow you to easily bolt it to the wall or the floor. HOWEVER, most fire proof safes can not have holes is the safe as that would reduce the fire protection. To bolt these safes in we suggest using a silicon-based glue to glue them to the floor.