Yes, the Carpet Shampoo can be used as a stain remover, but only in concentrate form. The Stain Remover was designed for use in concentrated form and should not be used as a carpet shampoo in carpet extraction equipment.

Following the entire Try for Dry program usually shows remarkable dryness within a few weeks and results in complete dryness (14 consecutive dry nights) within 3 months. In cases which do not get dry by this time the child's doctor may consider referring you to a specialist, such as a urologist, to further examine your child.

That depends on the ambient humidity (surrounding area). The more humid the area, the faster the dry time, which usually varies from 3 to 6 hours.

Anaerobic adhesives do not contain solvents, which must dry. For an anaerobic adhesive to cure, it must be in contact with active metal ions and contact with oxygen eliminated. Outside of a bonded joint, anaerobic materials will not completely cure. Inside the joint, cure rates can be controlled by changing product and primer. Heat can be used to accelerate cure rate.

It will take approximately 20 - 60 minutes for it to dry to a smooth, dark finish. To ensure complete transformation of rusty surfaces, apply a second coat. Allow 48 hours of cure time before the application of the finished paint coat (humid conditions may vary drying time). For long lasting protection, the cured rust converter coating should be sealed with two coats of high quality oil-based paint. No other primer is required.

Drying time depends on several factors: the type of fiber and how condensed it is. Synthetic carpets dry between 1 to 8 hours under proper conditions.

Like anything, it will depend on the circumstances; such as how wet is the towel, where the Warmrail is situated and so on. If you use a bath towel in the evening it will be dry and warm when you use it in the morning. For fastest drying time, have less layers of towels so the moisture can pass through quickly. For maximum warmth, use multiple layers of towels to trap the heat.

In hot weather TIMBERMATE dries quicker. In cold weather the depth of fill will determine the drying time. You can speed up the drying time by using a heat gun, hair dryer or light.

Between 2 ? 4 hours in normal humidity conditions. Thereafter the next coat can be applied without sanding. One can work quite fast this way.

Usually a printed garment takes about an hour to dry. Some areas may have more paint than others and take a bit longer to dry. A rainy day can slow down the drying time.

Concrete floors should be properly cured and adequately dry before installation can be started. The time for a new base to dry out is estimated at one day per 1mm thickness of concrete up to 50mm. Greater thicknesses require considerably longer to dry out. Remember to check the moisture content using an appropriate method.

Generally asphalt emulsion sealcoat is dry and ready for use 12-24 hours after application. The dry time is dependant upon on heat, humidity, shade and cloud cover.

This depends on many factors: how thick the carpet is, how soiled it is, airflow in the home, and humidity. In most cases carpets will be dry in two to eight hours.

The cracksealing material is applied at 300° F but cools to the touch in minutes and can be open to traffic almost as fast without worry of it tracking.

Cold weather and humid conditions can lengthen the dry-out time, while warm, sunny weather will speed it up. Dry-out times can vary from a few days to as long as six months, but the film will eventually dry completely. Moisture that is trapped during the installation process can cause bubbles or a slightly cloudy appearance. This is normal. Do not try to “pierce” or cut the film in an attempt to drain the trapped moisture. This will damage the film.

Substrate Material - With typical water based glues, the water will be absorbed into MDF, particle board, etc. faster than a solid wood like oak. Therefore, the drying time is shorter. You can usually speed up the drying time by putting an electric blanket over the vacuum bag. This can raise the temperature to 90 to 100º and cut the normal drying time in half. The following are typical drying times for a shop at 70º and using a substrate that is not a solid hardwood, i.e.

It depends on the weather. The sealer dries faster in the sunlight and heat. It typically takes 2-3 hours.

The new Dry-Brik II is formulated to last two months. If you have the original style Dry-Brik (in the gold foil wrapper), the longevity may vary. No, for all that extra effort, you won't see any difference in the life of the Dry-Brik. That's because when the Dry & Store lid or drawer is closed and it's not turned on, there's no air movement, and air is not being actively drawn into the closed unit. DO keep the drawer closed during the daytime.