What is the largest fuse I can use?
Powerlet :: FAQsEven though our harnesses are will conduct up to 20 amps safely, a 15 Amp fuse is the highest recommended. Please read the Fuse Sizing Primer to learn why.
Related QuestionsWhich punches do we use for FUSE?
Faq'sThe punches used for FUSE vary from 0.4mm (for single hair FUs ) to 0.75mm (for majority of FUs) to 0.9mm (for exceptionally big 4-5 hair FUs) The punch to be used depends on how widely the hair of a FU is spaced out while emerging from the skin. Trying to extract larger FUs with punches whose diameter is less than that of the FU at point of emergence from the skin is, obviously, illogical. Yes, hair can be grafted in between existing hair.
Related QuestionsWhy fuse at the battery?
Amplifiers - FAQInstalling a fuse of the proper amperage on your power cable protects everything between the fuse and your gear from a short circuit. A short circuit occurs when a current-bearing wire makes contact with bare metal (like your car chassis). Because your entire car chassis can be considered "negative" or ground, you can think of a short circuit as positive touching negative. You definitely don't want this to happen, but if it does, a properly installed fuse will prevent a fire or other damage.
Related QuestionsHow big should the fuse be?
Amplifiers - FAQIf you're installing just one amplifier, the fuse at the battery should simply match or slightly exceed the fuse rating of the amplifier itself. If you're installing two or more amplifiers, just add their fuse ratings together and install a fuse rated roughly equal to this sum. Generally, it's better to go slightly higher than lower, but a margin of five amperes is acceptable. Say you have three amplifiers, two with fuse ratings of 20 amps each and one with a fuse rating of 25 amps.
Related QuestionsFaq'sFUSE (in-vivo follicular unit separation extraction) is a safe, minimally invasive, virtually non-scarring technique of extracting single follicular units (FU) without the use of any scalpel, linear cuts or stitches. It involves separation of the graft bearing skin till the level of mid dermis with fine and sharp micro punches.Related Questions
Which needles do you use for placing FUSE in the recipient scalp?
Faq'sWe are currently using a range of needles varying from 20 gauge to 24 gauge. Often the choice of the gauge depends on the girth of the FU to be placed. We value safety above all. It is no point trying to place a graft thicker in diameter than the diameter of, say, a 24-gauge needle into a 25 gauge needle hole. Remember, not only do we have to create minimal trauma in the recipient area by the needle, we also have to ensure minimal trauma to the FU during placement.
Related QuestionsWhat size fuse does my trim tab system use?
Frequently Asked QuestionsOn a 12 volt system use a 20 amp in-line fuse on the power lead to the helm control. (24 & 32 volt systems use proportionally smaller.)
Related QuestionsWhat version of FUSE do I need to use FUSE with Linux 2.4?
FUSEWiki - FAQFUSE 2.5.3 (supports 2.4.21 or later); later versions include a kernel module compatible with Linux 2.6 only (Linux 2.6.9 or later, as of FUSE 2.6.1).
Related QuestionsR/C Tank Combat - Frequently Asked Questionsyou want the max amperage of the fuse to be about two thirds of the total stall current of the motors. For example, a 12v EV warrior pulls 99.2 amps at stall, so the fuse needs to be at least 60 amps. You should also use slow blow fuses (car audio) because they can handle sudden spikes of stall current (turning), but still blow if your tracks lock up.Related Questions
What's the largest hard disk I can use?
Frequently Asked QuestionsWe have had reports of disks at least as large as 400Gb being used. You can find some information in the Hacks section of our links page. Remember that you need to choose a drive that does not consume much more power, or generate much more heat, than the original drive fitted.
Related QuestionsWhat is the largest tire I can use?
Without any modifications, 15" x 8.5" wheels (front and back) with 4.5" backspacing and P245/60R15 tires will fit. For 16" x 10" (front) and 16" x 10.5" (rear) with 5.375" backspacing and P255/50R16 tires, the inner lip of the fenders will have to folded under. Also the control arm (near the upper ball joint) may have to be grinded up front and shock mount clearance should be checked in the rear.
Related QuestionsWhat is the largest memory card I can use?
SuperCard Store - we ship worldwideGB, although many people have reported using 4GB succesfully - please let us know if you have. Windows XP will not let you format a 4GB card in FAT format (it forces FAT32, which the SuperCard cannot read), so you need to know what you are doing to get 4GB working.
Related QuestionsWhat's the largest amount of flash that I can use for ReadyBoost?
SupportYou can use up to 4GB of flash for ReadyBoost (which turns out to be 8GB of cache after compression).
Related QuestionsWhat size breaker or fuse can I use in a 46377 type Circuit Breaker/ Fuse Block?
Cole Hersee Resource CenterThe breaker or fuse should not be rated for more than 25A per breaker or fuse with the total of all items used not to be more than 150A.
Related QuestionsDoes KOMeter? have a fuse?
Frequently Asked Questions (FAQ)Yes, but it is not serviceable by the user. The fuse provides protection from mis-wiring. Should the unit fail to power on, Contact Us for service.
Related QuestionsDo I need a separate fuse block too?
Amplifiers - FAQUnless your amplifiers are among the few that don't come with fuses installed, the answer is no. The reason you see these "redundant" fuses is that in the early days of car audio competition, amplifiers frequently didn't include their own fuses, or if they did, often hid them behind panels that were hard to get to, especially in the heat of competition. Today, the use of such fuse blocks is largely a matter of style. But that's OK — looking cool definitely counts.
Related QuestionsIs there a limit on the largest hard drive I can use?
MP3 Jukebox Player Frequency Asked QuestionsThe unit supports LBA mode FAT32 file systems, so the theoretical limit is 2048GB. Practically speaking, a 40GB hard drive should comfortably contain 5000-10000 MP3 tracks, depending on the bitrate.
Related QuestionsWhat is the largest image I can use with PowerWEB Zoom?
PowerWEB Zoom FAQsWhile there are no hard-coded limits to the size of an image that may be used with Zoom, there are some server resource limitations that must be taken into consideration. Zoom renders resized images and tiles on the fly and stores them on disk. If using particularly high Quality and InterpolationMode settings, these images may take up a significant amount of disk space.
Related QuestionsWhat is the largest memory card I can use in a Meridian?
Robert Lipe's Magellan (330, SporTrak, Meridian) GPS FAQFirmware versions later than about Q2 of 2004 fixed the compatibility problems that had previously been observed with "large" cards. The yahoogroups report success with 2GB cards without issue.
Related QuestionsHow many amps do the blowers use? How big should the fuse be on the customers outlet?
FAQ's about Moonwalk Rental EquipmentA 1hp blower uses approximately 12.8 Amps on Startup and 10 amps while running. It should be noted that alot of you customers will have a 15 or 20 amp circuit. Be sure that the customer knows not to put any heavy loads on the circuit, Such as a hairdryer or vacuum cleaner as this will most definitely trip the breaker turning off the blower in the process.
Related QuestionsAre there any standards relating to use of MV-fuses in combination fuse switch units?
Pro Fuse International - Fuse User - FAQYes, IEC 60 420 gives guidance for the combination of a fuse link according IEC 60 282-1 and a load break switch according IEC 60 265-1.
Related QuestionsWhy is FUSE better than other techniques?
Faq'sApart from the fact that the FU’s are carefully separated under direct vision to avoid any inadvertent damage in FUSE. A freely taught and shared technology – Dr. A has distributed knowledge about performing FUSE freely on the net for other doctors to emulate and improve. FUSE is the only technique to be examined by the maximum number of doctors including many so-called competitors for flaws.
Related QuestionsDo you perform only FUSE or FUHT too?
Faq'sWe perform both FUSE/fue grafting as well as Follicular micro grafting (strip method of harvesting the donor area). While follicular micro grafting does give a line like scar in the donor area, it is normally not visible even under a hair growth of 1to 2 cms. Similarly, FUSE gives no obviously visible scarring but the person does have to roam around with a shaven head appearance for a couple of weeks after the procedure which does not suit some patient’s schedule.
Related QuestionsCan we fuse the parts together?
Engineers WeekParts cannot be glued or otherwise permanently attached to one another. Electrical tape may be used to secure wires but not for structural purposes.
Related QuestionsWhat if I cannot find the fuse I am looking for?
Alan's Sales :Please let us know what you are looking for and the date in which you need it. We will do what we can to find what you need. We cannot promise we will find it, but we will do our best to service your request. If you oftentimes purchase fuses simply to replenish stock, remember to bookmark us on your browser and check back often for newly acquired stock.
Related QuestionsWhere should a fuse be installed?
FMA Direct : FAQsIn the power line from the ESC to the motor. Do not put a fuse in the battery lead as all power to the servos and receiver will be lost if the fuse burns out. NOTE: It is wise to put a fuse in-line between any motor and any ESC that equals the current rating of the ESC.
Related QuestionsHow do I fuse my equipment?
Excelsys Technologies - 3genThis is a class one power unit and must be earthed by a secure connection to ground. If in the end use equipment, the incoming mains cable earth wire connects directly to the "GND" connection on the 3GEN unit without being interrupted or junctioned on its way to that connection, then this connection forms the main protective earth of the system. To comply with IEC950, EN60950, UL1950, BS7002 and BS6204 requirements then this must be marked with the symbol defined in the IEC417 No. 5019a.
Related Questions