Answer: Up to four Nexia devices of any type (CS, PM, SP) can be linked together by using the NexLink Transmit and Receive ports on the rear panel of each unit to create a daisy-chain configuration. Keep in mind that NexLink does not share control information, only digital audio; therefore, each Nexia?s control Ethernet port must be connected to the control network.

Answer: If there is no need to share digital audio between units, there is no practical limit to the number of units that can be included in the same .nex file. Up to four units can share digital audio over the NexLink bus. See the separate NexLink FAQ for a complete discussion of NexLink.

Answer: NexLink is a Biamp Systems' proprietary high-speed audio network protocol that allows the sharing of multiple channels of uncompressed digital audio between Nexia units. Large and complex audio systems can be created by using NexLink to add signal processing horsepower as well as additional I/O to the design.

Windows NT/2000/XP Pentium II 300MHz or faster PC with at least 64MB RAM and a 10/100baseT network card(NIC) Enough Cat5 ?straight-through? Ethernet cables for both Ethernet connections and NexLink connections to all devices.

Answer: Up to 12 devices can be connected to a single Nexia. A Nexia system that uses multiple Nexia units can have up to 12 RCB devices connected to each Nexia in the system.

When using multiple effect units, you'll find that the order in which they are connected can significantly affect their voicing. While we'd suggest you experiment, ultimately finding which works best for you, here's a generalized guideline to get you started; Guitar > Wah > Compressor > Overdrive (including Distortions and Boosters) > Modulation > Delay > Reverb.

If using distortion, overdrive, booster, compressor, wah, etc..... and/or if your amp does not feature an effects loop, connection to the amp's input would be appropriate. To do so, simply use a good quality, screened (shielded) instrument cable to connect your guitar to the effect's input (Fig. 1.1). Use another instrument cable to connect the effect's output (Fig. 1.2) to the amplifier's input (Fig. 1.3).

If you use a commmercial ISP such as RoadRunner, IBM's ICE, or another service, you may have trouble connecting to some of the libraries' databases. To remedy this, an authentication service is available by connecting through our proxy server. NOTE: This only provides access for members of the OSU community. Those who are not affiliated do not have access to some of our services.

Fast! Because Copper.net does not require you to install proprietary software that can slow down your connection, you should connect faster then you did with your previous provider. Copper.net provides an industry standard "56k" dial up connection. Your modem, the telephone lines and switches in your area, and user traffic affect the actual speed at which you connect. Copper.net uses updated Internet servers and equipment to provide you with the best connection we possibly can.

To connect a turntable to any NAD unit, (with the exception of the 160/162) you will need a phono pre-amp, our PP2. The PP2 phono pre-amp is a simple and inexpensive way to add high-performance phono capability to a pre-amp or integrated amp with spare line input. With the PP2, all turntables are made compatible with the amps. There are two different types of turntables: moving coil and moving magnet. You have to know what type you're buying, and set the PP2 accordingly.

Answer: NexLink is not CobraNet, although both allow the sharing of multiple channels of digital audio over a single Cat-5 cable. CobraNet is essentially a standard Ethernet network which is designed to share ?packetized? digital audio. NexLink, on the other hand, is a proprietary audio network protocol that is unique to the Nexia series of products. It is not compatible with Ethernet, CobraNet, or any other networking standard.

Answer: When two or more Nexia I/O combination blocks are placed into a layout, the Nx icon in the Object Toolbar becomes active. Selecting this block and clicking in the layout causes a dialog box to appear prompting the user to enter the device number of the transmitting unit and the device number of the receiving unit. Clicking the OK button will display the NexLink Input and Output blocks.

To verify the IP address of your PC has been set go to the Windows Start menu>Run>type "command">at the C: prompt type "ipconfig" This will display the IP setting of you PC. Verify that the correct IP address is setup on your PC. To verify the IP address of Nexia, go to the Windows Start menu>Run>type "command">at the C: prompt type "ping" followed by the IP address of the Nexia. If the ping replies from the specified IP address, you have a verified connection from your PC to the Nexia.

You cannot connect directly to an IP using a phone line. There is a way, however, by using the internet. Connect to the internet through your ISP(cannot be AOL), then once connected you can start the client up and put in the IP address of your Watchdog. [FAQID No: 138]

Yes. Windows XP has Internet Connection Sharing (ICS) which allows sharing of a single internet connection.

First make sure the line is a single line. You may connect your IPStar to the fax machine line to see if your PBX system can work along with IPStar. Connect your IPStar to the C.O. access prefix so that all extensions can access to it. When you want to dial up to the Internet, you may just dial # # from your telephone set so that you won't have to reach the IPStar and press the middle flash button.

First, if you wish to try Portal without setting it up completely for Materia Magica you can simply hit the Quick Connect button. This will bring up a box asking for connection information; in here place materiamagica.com as the Host and place 4000 as the Port. Then the Accept button should un-gray itself, click it. A small box will popup that says Connecting, then a new window will open up connected to Materia Magica.

YES ! You can connect to the internet by accessing another members internet connection which is usually high speed (ADSL / Broadband). Of course, small contributions from members are welcome to help with the cost of providing internet. One concept is that members group together and purchase a high speed connection (currently up to 2Mbit/sec in Newry area) and share the cost of this between them.

UAN has made available a message board for the purpose of making connections with adopters of PMU horses, rescue organizations, and women who are avoiding PMU drugs. You can access the message board here. Please do! The more people who know about and use PMURescue.org the more horses will be placed in homes. We want PMURescue.org to be available to rescue groups and ranchers in need, so please--go ahead and spread the word!

Make sure that your firewall allows communication over the TCP protocol, range of ports 9000 - 9020, 9100-9101 in both directions. ports not listed here are reserved for future use or servers (e.g. each MV server use own TCP port for connection ..)

For general setting please see "What are the general settings for Dial Companion?" All information on how to connect using your Dial Companion service, can be found within the "How to connect to the Internet using your Demon Dial Companion" guide available by visiting here. Ensure you are presenting CLI (Calling Line Identity) - please see the section on "How do I ensure my CLI is presented when dialling in?"

Yes you can use an ISDN terminal adaptor if you have an ISDN line. It is not possible for this to work on the same line that has been converted to Broadband.

There are known problems with Netscape and Internet Explorer's implementation of Java. We have a LOT of MAC users who use ParaChat with no problems at all. However for some MAC users it either does not work at all or works in a limited manner. If you are a Mac user and have any additional information we can add here please let us know by sending email to info@paralogic.com , we want to know!

And then add these lines to the bottom of the sip.conf file (obviously, in both of these, you need to replace <username> with your username and <password> with your password. You could also add contexts to handle dialing other things if you wanted. If you wanted a catchall extention to handle ALL calls and sent them to IdeaSIP, you could have something such as: You would then need to add a sip.

Use File -> Publish Web -> FrontPage or SharePoint Services and input "http://YourUserName.pairone.com" under Remote Web Site location.

Connect your InterStar to the C.O. access prefix so that all extensions can access to it. You can also connect InterStar with your own extension side for individual usage. Make sure the line is a single line. You may connect your InterStar to the fax machine line to see if your PBX system can work along with InterStar. If you connect InterStar on the C.O. line, when you want to make the Internet call, you may just select the specific line and make the phone call.

When you have successfully connected to a database, you will see all the tables it contains. These are the tables on which you can run data matching sessions with Paribus and from which you can find duplicate data. A table comprises fields into which you will have entered data. In the account table, for example, you will find fields called "Company name", "Address" and "Post code".

Yes, depending on which Macintosh OS you are using. SNAP currently supports Macintosh OS X 10.2 and, unfortunately, nothing earlier. What is PARNET? PARNET is a network consisting of the four Western Australian universities - The University of Western Australia, Curtin University of Technology, Edith Cowan University, and Murdoch University - and the CSIRO. Access to PARNET resources from UWA computers (including through SNAP), is free.

Yes, this is the easiest way to connect to mcsi.net and the way that we recommend the most. Review the manuals or on-line documentation for Dial up Networking.