Areas Where Foam Can Be InstalledThere are a few different places in which foam insulation can be installed. Usually foam insulation is placed in various areas throughout a home during its initial building phase. This includes the attic, basement walls, between floors, and as a spray insulate on a roof. Foam insulation is also used within office buildings and businesses.

The National Association of Homebuilders (NAHB) named BioBased 501 the "Outstanding Green Product of the Year" in 2003 at its Green Builders Conference in Baltimore, Maryland. This is the only insulation product that GreenBean uses.

The Spray Foam insulation is sprayed into place onto a studded wall by a certified GreenBean professional. As with any open surface, the foam insulation can be sprayed once electrical and plumbing services are in place. It then expands to up to 100 times its initial volume in seconds, permanently adhering to the surfaces of the surrounding building materials and sealing all gaps.

In addition to sealing off eave areas to mitigate ice damming in many cases, spray foam insulation (several types are available) is the best choice for insulating new homes and for extensive remodeling projects, because of its air-sealing qualities. The amount of energy lost by convection (air movement through the building envelope) is much greater than what is lost by conduction (heat transfer through a solid). R-value is important, but it measures only heat lost by conduction.

More Information About InsulationTo find more information about foam insulation, there are numerous resources available on the Internet. The first place to start looking for information about foam insulation is agencies and organizations such as the Foam Insulation Association, whose informative Web site outlines the standards within the insulation industry. A great source of information is the National Commercial & Industrial Standards Manual found on the www.insulation.org Web site.

Quite simply, it is "insulation plus sealant". As a rigid cellular plastic with over 95% closed cell content, Spray Polyurethane Foam Insulation acts as insulation, an air barrier and, in some cases, also a vapour barrier. Spray Polyurethane Foam Insulation will cut energy costs and improve comfort levels in any building.

Why Should Anyone Use Foam Insulation?The American Council For An Energy-Efficient Economy released statistics outlining the amount of money that can be saved by having all building properly insulated. The $13 billion dollars wasted as a result of poor insulation equates to approximately a savings of $200 for each homeowner. If your home is not properly insulated, more energy is needed to keep the home cold when using the air conditioner in the summer, or heating the home in winter.

BioBased Insulation is sprayed into place onto a studded wall by a Certified BioBased Dealer. As with any open surface, BioBased Insulation can be sprayed on once electrical and plumbing services are in place. It then expands to 100 times its initial volume in seconds, permanently adhering to the surfaces of the surrounding building materials and sealing all gaps.

BioBased Insulation is installed after the windows, doors and roof systems are in, the electrical, framing and plumbing inspections are complete, and after any other electrical or mechanical system located behind the drywall is installed. It is the last installation to take place before drywall installation.

Although Icynene, or recycled wood fiber treated with Borax, spray insulations are recommended to completely seal the shell, fiberglass battens may also be used to insulate am-cor? steel frames. First install pipes and wires through the factory-punched holes in studs, joists, and rafters using plastic grommets to keep service runs from touching the steel frame. Then spray insulation, or pack battens around the services and into the C profiles for complete thermal break.

Icynene Insulation is sprayed-in-place by a professionally trained and licensed contractor after electrical and plumbing services are in place. As the foam is installed it expands 100 times its' original volume in seconds, completely filling all the cracks, joints and spaces between other building materials to form an air barrier around your home. Drywall is installed directly over the Icynene Insulation.

The Icynene® Insulation System is installed after the windows, doors and roof are in, the electrical and plumbing inspections are complete, and after any other electrical or mechanical system located behind the drywall is installed. It is the last installation to take place before drywall installation.

The Icynene Insulation System® is installed after the windows, doors and roof are in, the electrical, framing and plumbing inspections are complete, and after any other electrical or mechanical system located behind the drywall is installed. It is the last installation to take place before drywall installation.

For new construction or renovations, the insulation is installed after the windows, doors and roof systems are in, the electrical, framing and plumbing inspections are complete, and after any other electrical or mechanical system located behind the drywall is installed. It is the last installation to take place before drywall installation. On existing homes, the spray foam insulation can be installed to the attic, roof line, and sub-flooring to seal in the house.

Cavity wall insulation is quick, clean and relatively inexpensive to install. It's injected into the cavity from the outside, which takes approximately three hours in a three bedroom semi-detached house.

Our mineral fibreglass is simply rolled between and over the joists to a recommended depth of 270mm. It effectively acts as a blanket, trapping heat rising from the house below.

We compared an ASTEC-coated metal roof without insulation with another metal roof having 10 cm of polyurethane foam. This allowed us to calculate the surface temperature under identical simulated environmental conditions. In addition, the roofs were given a "typical" 40 m length to determine the thermal shock reduction provided by ASTEC.

All our service technicians carry foam on board their vans so, if a leak in the piping occurs, they can dig out the foam, repair the leak, refill with more foam and tidy any mess they may make in the process. This causes no extra concern or work for the customer (apart from perhaps making the engineer a cup of tea after all that thirsty work!).

Spray Foam Insulation has excellent sound absorption properties and sound transmission properties. For a 2" x 6" wood cavity insulated with Spray Foam Insulation the Noise Reduction Coefficient (NRC) is 75 and the Sound Transmission Coefficient (STC) is 49.

No! Spray Foam Insulation is a clean product. It meets off gassing requirements of CGSB 51.23-92 for new residential construction. No toxic or carcinogenic products were detected. The flame spread classification of Spray Foam Insulation as tested in accordance with CAN/ULC S102 is less than 500 and in accordance with ASTM E-84 is a class 1 (21) at a thickness of 6". The fire testing was conducted from the top of the Steinner tunnel without any product dripping during and after tests.

Yes, Spray Foam Insulation is an ecological product certified by an independent agency: "the Environmental Choice Program (EPC-40) of Environment Canada".

This type of insulation was installed in properties primarily during the late 1970's and early 1980's. It was discovered that UFFI could cause an extreme allergic reaction to the formaldehyde gas which came from this insulation. Although the majority of UFFI has been removed from houses, a prudent buyer should still be aware and concerned about this issue. Check the Seller's Property Disclosure Statement to determine whether UFFI has been disclosed.

Spray foam is install at the same time as other insulations would be. After the mechanical work is done and inspected and before the drywall is installed. Back to Top

Foam insulation is sprayed onto the the external fuel tanks in a gooey form and then becomes hard as a brick but light, like Styrofoam. It keeps the liquid hydrogen and the liquid oxygen fuel super cold. Shuttles ride these 15-story tanks during liftoff, then the tanks separate. NASA video showed that 81 seconds into the flight, a 20-inch, 2 1/2-pound piece of the foam fell off and struck Columbia's left wing. The shuttle Columbia was moving more than at twice the speed of sound.

Answer: The board has an R-value of 4.3 but the increased insulation value of the wall can’t be determined.

Most existing houses have at least some level of insulation in the attic. Many houses over 15 years will find that the depth of existing insulation is usually quite small as old glass/mineral fibre will settle over time and will be much less effective. There are two choices here: the existing fibre glass can be removed or Sheep Wool Insulation can be rolled out over existing insulation.