It is a tough flexible coating...Tool Handle Dip. Rather than brushing I have found that it is better to apply it thick with a serrated squeegee. Then lightly tip it off with a brush dipped in solvent. This system does not particularly soak into the fabric weave and yields the best ripstop results. Plasti-Dip does add a fair amount of weight.

Plasti-flor? tiles are simple to install. All you need do is align the edges and then 'clip' them together with the rubber mallet to seal the interlock. Because the tiles are not stuck down, they can be altered, added to or reconfigured at any time.

Everyone from large industrial concerns such as motor assembly plants to homeowners. Excellent results have been recorded at vehicle centres where tyres, windscreens, exhausts and batteries are fitted, for example. Besides their value as a flooring surface, there is the added benefit of noise absorption that relieves the high sound levels that are so much part of these environments. Motor vehicle showrooms, laboratories, warehouses, schools and gyms also use the product to great effect.

In the corporate environment, the tiles can be used to create floor protectors under desks or in high-traffic areas. Floor protectors work equally well on carpeted, wooden or ceramic flooring. As the tiles have anti-static qualities, they also work well in any area where computer equipment is used. Domestically the tiles are used extensively in garages, dens, laundry-rooms, storerooms and kitchens.

All over the world. Besides Africa, the company has satisfied customers throughout the world, including Argentina, the United Kingdom and many more.

Most CERAM-KOTE coatings are considered two component systems. Part A (base) is a ceramic/epoxy solution that is mixed with Part B (curing agent). Please see each individual Product Data Sheet for mixing and application instructions. With extreme care, a two-component kit of CERAM-KOTE may be broken down into smaller quantities. Careful and exact measurements must be made to assure that the proper ratio of Part A to Part B by volume or by weight is maintained.

KLASS KOTE is a protective, decorative, 2-part epoxy coating system. It can be used on a wide variety of substrates and in numerous environments, which require a highly protective and attractive coating.

KLASS KOTE will harden to tack or dust free in 20 minutes to 1 hour. After 4 hours, the film will be thumb print free. After 24 hours, the painted surface/object will be ready to be placed into most normal situations (package able) but complete cure (sword hardness) will generally take several days. In most normal conditions, KLASS KOTE epoxy will be suitably hard within a 24 hour period. Refer to Test Results page.

As CeRam-Kote does not have control of the application of CERAM-KOTE, CeRam-Kote can only guarantee that CERAM-KOTE is manufactured to our strict manufacturing specifications and the testing accomplished to the best of our knowledge is correct. However, it is the responsibility of the end users to determine if CERAM-KOTE will work for them.

Plasti-flor? tiles are not glued down. The tiles have a unique, strong interlocking edge and are loose laid.

While it is wet it can be removed with Xylene (Xylol). After drying it can only be removed with a strong paint stripper.

Dried Protecta-kote is non-toxic. Liquid Protecta-kote contains solvent, Xylene (Xylol), and isocyanate. Prevent contact with eyes and skin, do not ingest and avoid inhalation of solvent vapours. Use in a well ventilated area. If spraying Protecta-kote a mask with approved cartridges must be worn.

Approximately 0.5 litre is required for each coat per square metre. For normal use 2 coats is sufficient however 3 coats are recommended for areas of high wear. Therefore depending on the material and technique being used 1litre will cover 1-1.5m2 in normal use and 0.6-0.9m2 for areas of high wear. It is always better to apply many thin coats than few thick coats as this will give better overall cure times and better overall results.

The recommended two coats of Protecta-kote should give you a thickness of 0.83mm (33mils). Where Protecta-kote is being used in high wear situations three coats are recommended giving a thickness of approximately 1.24mm (49mils). These figures will vary slightly depending slightly on the material and technique being employed.

CERAM-KOTE coatings are coatings that utilize various highly modified resins. These resins are then loaded with different types of ceramic particles to achieve the attribute needed, whether that be abrasion, chemical or corrosion resistance. CERAM-KOTE coatings encapsulate surfaces with a ceramic shell that protects the surface from its particular environment.

Yes. A short nap roller (approx. ?" or 6.35 mm) of good quality is recommended. The shorter the roller nap, the lesser the stipple effect.

All of the above coatings are polymer coatings, not a process. Just like paint, the results depend on the metal preparations and application method. If you apply paint to steel it will not adhere, even if you sand it and ruff up the finish prior to application. This is why you have to prime the metal before you paint it. The paint has to have something to stick to. The problem is that with any painted surface, if you prime it and paint it, it is too thick for most gun applications.

As Freecom does not have control of the application of CERAM-KOTE, Freecom can only guarantee that CERAM-KOTE is manufactured to our strict manufacturing specifications and the testing accomplished to the best of our knowledge is correct. However, it is the responsibility of the end users to determine if CERAM-KOTE will work for them.