No. These machines are for cutting wood products. The only exception is soft aluminium extrusion. This can be cut provided a fine tooth blade (at least 60 tooth) suitable for aluminium is used and the material is securely clamped.Details of blades can be found here.

The Ventmaster can cut through wood framing, sheet metal, asphalt shingles, and green wood. It is even effective on metal roll up doors commonly found on industrial warehouses. It can also cut through car bodies, hoods, and windshields. Yes. Contact Tempest Customer Service at 800-346-2143 for more information on the Ventmaster 375-K rotary cutoff saw.

Endurance® can be cut with most saw types. When using a power miter saw, a high tooth count (80 or more) carbide tip is best. Be sure to have the blade up to speed before beginning your cut. Hack saws and other saw types with metal cutting blades will do the job.

No. It is not recommended to use a circular saw to cut pavers. A brick splitter or a high-powered saw with a diamond blade is recommended. These are readily available to rent at Michigan Skid Loader (www.mslinc.com) or other equipment rental stores. For a few cuts, we can cut them for you for a small charge.

Not yet, but we are working on it. Our system will be able to measure 8 feet to the left and 8 feet to the right.

Preferred method is a B-2 Beverly Shear. Electric shears and even nibblers will also work. Cheaper methods include: a jigsaw with metal-cutting blade [look for at least 18tpi blades, and cut patiently, not forcing it]; hacksaw or jeweler's/coping saw; chisel.

MetaL is shorthand for Meta-programming Language. Meta-programming is a method to develop computer programs. It works by generating source code in a target language from a program specification in a higher level language. MetaL programs source code is based on XML. MetaL compiler engine can be used to generate the same program from MetaL source code to potentially any target language. Currently supported target languages are PHP, Java and Perl.

A woven valley is when the shingles from both sides of the valley extend across the valley and are woven together by overlapping alternate courses as they are applied. A closed-cut valley is when the shingles from one side of the valley extend across the valley while the other side is trimmed back approximately 2 inches from the centerline.

Technically, yes, but it takes at least 200 watts before the CO2 starts marking bare metal. The lasers manufactured by ULS are not for cutting metals. Marking bare metals such as stainless can be done with the ULS HPDFO optics.

We found that older version Hitachi's (mostly the 046 and 047) had read/write errors where you would get an on screen error (E46) or the Xbox would not read any discs or would reboot itself. The Hitachi fix was first release as a PCB to solder to the internals of the Xbox 360 ODD unit. This is no longer required and there is now an external Sata adapter that plugs into the back of the ODD and then the ODD Sata cable plugs into that. This resolves all Hitachi problems.

In partnership with government clients, The MITRE Corporation (MITRE) is a not-for-profit corporation working in the public interest. It addresses issues of critical national importance, combining systems engineering and information technology to develop innovative solutions that make a difference. MITRE's work is focused within three Federally Funded Research and Development Centers (FFRDCs). One FFRDC performs systems engineering and integration work for Department of Defense C3I.

Plywood, MDF (medium density fiberboard), and Hardboard ? If measured floor-to-ceiling height is 8' or less, subtract 1/2" from the measurement to allow 1/4" expansion clearance top and bottom. Transfer these measurements to panels for cutting. If using a handsaw or table saw, mark and cut the panels face up. If using a portable circular saw or saber saw, mark and cut panels face down.

Answer: When a lane is slip formed, and allowed to cure for a day, a cold joint is formed. This cold construction joint would have tie bars placed into it. Then an adjacent lane is poured up against this new lane. The longitudinal joint will remain tight due to the tie bars. It is anticipated that very little water will penetrate this joint. Therefore, to saw cut the longitudinal joint would be difficult at best and not very beneficial. With a tight cold joint, a sealant would not be needed.

Almost all of our barrels have a bandsaw cut one inch from the muzzle end of the barrel. This indicates that the barrel is not useable beyond that point. When we hand lap our barrels, we do so from each end of the barrel. Because the lapping compound is applied to the lap directly next to the ends, the bore becomes worn slightly oversize. This oversize condition does not extend more than .50"-.

A sword was never a warrior's first choice when trying to break through armor. A spear, pike, or halberd (picture below, modified from Tenshaku) is much more capable of delivering much more force to a target than a sword. Also, many Japanese styles of sword combat taught to strike at the weakest points of a suit of armor - the joints and gaps - than try and push through a helmet or breastplate. Similar techniques were employed around the world.

Met-Tile panels are made of Zincalume™ coated steel that provides excellent corrosion resistance for most applications. In oceanfront climates (i.e. within 1800 ft. of a salt water body) or other unusually corrosive environments, an aluminum substrate is recommended in place of steel. Visit the Met-Tile aluminum page for further instructions.

Yes by using the Maximus Toolbox app and Slax CD. (Maximus is working on an update for Native USB compatibility)

If you need your water cut on, simply contact the water billing office at 989-3055. If you need your water cut off , call the same office and ask to have a final reading for your meter.