This mainly will depend on the weather. On average a Pressure Treated Pine deck can be sealed in approximately 45-60 days from installation. A Cedar or Redwood deck can be sealed within 21 days. If you have a fair amount of rain you will need extra time for drying the wood out. Essentially you are making sure you don't seal in any moisture as this will promote rotting from the inside out.

That depends on our climate. Decks in the direct sunlight tend to fade and dry out; decks in humid and shady areas grow algae and fungus spores. Both problems require attention yearly, or no later than two seasons apart. See similar questions...

We need a minimum 50 degree temperature to safely let deck preservative products cure and dry properly. See similar questions...

I prefer to use a large brush or a mop. You want to get large amounts of Stain Solver liquid on the deck surface. Hand pump sprayers often apply too little solution to the surface. If you must use a sprayer, make sure the product has dissolved completely or you will clog the nozzle! Also, be sure you spray on lots of liquid. See similar questions...

There are products which are available upon request to wash and seal in one day. However, we choose a two-day method: Wash on the first day, and sand and seal the second dry day. See similar questions...

This primarily comes into play if your deck is well above ground (4' or higher). The answer is no. The reason you are sealing your deck is to prevent the sun from aging the wood and more importantly, to prevent rain from rotting your deck. Since the understructure never receives any real sunlight and gravity dictates that water will not stay on the underside, it is not necessary to seal that. See similar questions...

Yes. If you elect not to seal your deck it will age prematurely and will not last as long as a properly maintained deck. A properly maintained deck in our climate should last 30 years. for what type of sealer, we highly recommend to use cost as an indicator. There are definitely reasons why a gallon of Brand X costs $15.00 while Brand Y costs $40.00. Lower cost doesn't necessarily mean better value but it definitely could mean lower performance. See similar questions...

We recommend you let your deck dry for a minimum of four weeks after construction of your deck before we apply a penetrating sealer. The problem with new wood is that the grains are closed and the wood still contains natural chemicals called tannins and mill glaze. If left to nature, it would take 3-6 months for the grain to open and the natural chemicals to leach out. By using a combination of powerwashing and mill glaze remover, we can speed up this process. See similar questions...

Most sealers need a minimum of 4-8 hours to dry, although this can vary depending on the weather and the condition of your deck. If it rains soon after we apply the sealer, look for water spots. These are lighter discolorations on the wood similar to water marks left on fine furniture. If your deck has water spots, please contact us immediately to have the sealer re-applied. See similar questions...

Wood caskets typically do not feature a rubber gasket around the opening that makes them resistant to the entrance of water found in the ground around the gravesite. Wood is a porous material, which renders a gasket ineffective. If this is a concern, the use of a vault will protect the casket from elements found in the soil at the gravesite. Some wood caskets are available with inner liners constructed of metal with a rubber gasket around the opening of the liner. See similar questions...

Your user agent does not support frames or is currently configured not to display frames. However, you may visit the related document.] See similar questions...

Not at all. When done professionally, a very small amount of dried-out dead fiber is removed when your deck is getting a face lift. See similar questions...

The Invisagrip? Deck Fastening System was engineered for hard- and tropical woods. Therefore it can be used for all kind of woods (even softer more conventional deck woods,) also composite woods. See similar questions...

You should certainly protect your deck from unnecessary moisture intrusion and the harmful effects of the sun's ultra-violet rays. Use of a penetrating stain, containing water repellant ingredients in most cases will protect your deck best. The pigment in the stain will absorb the ultra-violet rays from the sun and protect the wood fibers from degradation. In most cases a stain will need maintenance every 2-4 years while clear sealers require maintenance every 1-2 years. See similar questions...

Commercial roofs can be sealed with an Elastomeric coating applied directly to the concrete cover. Rubber Membranes can Steel Rib systems can also be applied directly. More conventional finishes (such as residential shingles) can be installed over furring strips which are anchored directly to the concrete cover. Always follow the manufacturer's instructions for proper applications. See similar questions...

It is not recommended you place grills on wooden decks. If you do you must take measures to keep any burning ash or grease from falling onto the deck. The only people who can cook on their deck or patios are those living in single family houses or duplexes. Even then, it is a good idea to be sure the device is away from the house or overhanging structure. Keep children and pets away from the grill. Stay with the device while it is hot or a flame is present. See similar questions...

Hardwood decks such as Ipe, Mahogany, Brazilian Redwood, Massaranduba, Meranti, Pau Lupe, and Teak are extremely dense. This allows for less penetration of the stain resulting in more frequent applications. We do offer stains that are specifically formulated for these difficult to penetrate woods. See similar questions...

On a horizontal surface, Penofin may be expected to perform for an average of 9-18 months and 3-5 years on a vertical surface. The time will vary depending on the percentage of sunlight, weather, etc... Yes. All Penofin wood finish colors contain the same ingredients, just different amounts of colored pigments. However, you will not be able to make the surface lighter by applying a lighter shade. As always, you should test a small area before use. See similar questions...