Sanded grout is just what it says. It has sand added to it to increase the strength in a larger grout joint. It stops the grout from shrinkage and adds strength so that the grout will not crack. Un-sanded grout is used in many wall applications because of it's non abrasive texture. If the grout joint is going to be more than 1/8" you need to use sanded. The only time an un-sanded grout is used on the floor is with the installation of marble.

Unsanded tile grout is used on ceramic tile that has been installed with a grout joint width of less than 1/8 of an inch wide and should always be used on polished natural stone products. Sanded tile grout is used on tile with a grout joint width equal to or greater than 1/8 of an inch. See similar questions...

Non-sanded products are generally used for grouting tiles on walls where the grout joints are 1/8" or less. Sanded grout should be used where grout lines are larger than 1/8" but not greater than 3/8". See similar questions...

Grout is used to fill the spaces between ceramic tiles. When dry it has the texture and character of cement. It should only be used between products of the same type, usually ceramic or stone tile. It should not be used at the seam between tile and any other product, especially wood or wallboard. Products respond to heat, cold and humidity in different ways and grout is not flexible and will crack and fall away as different pressures are exerted by the different products it is attached to. See similar questions...

Cement – polymer based grout is based on cement and polymers as the name suggests whereas epoxy grout is based on resin, hardener and filler. Epoxy grout is resistant to most of the chemicals whereas cement – polymer grout is not. (refer epoxy grout data sheet) Mechanical properties like compression strength and tensile strength of epoxy grout is almost 100% higher compared to cement – polymer grout. See similar questions...

Original TTM 52 and TTM 54 models were built with metal toggle switches (ST 1) and a painted steel Decor plate (the one the faders stick through). When we revamped the design, we spread the controls apart slightly and added a Lexan covered Decor plate, as well as changed to larger plastic "bat handle" toggle switches (ST 2). Neither the Decor plate nor switches can be swapped between versions. Functionally and electronically the two versions are identical. See similar questions...

Exclusive: Original content you created that you guarantee has not been previously published online or in print and will not be published elsewhere in the future. Upfront payment offers are typically higher for exclusive submissions. Once you accept an offer for an exclusive submission, you assign full copyright ownership to Associated Content. See similar questions...

You can install our tiles without grout lines. You may choose to seal the tiles with nonsanded grout. See similar questions...

Epoxy grout (meeting ANSI A118.3) is quite different from cementitious grout and epoxy emulsion grout. Made from epoxy resins and a filler powder, the grout is extremely hard, durable, and nearly stain proof. Often times the bond between tiles is stronger than the tile itself. You might wonder why this type of grout is not used all the time. First, most installers find it harder to use than cementitious grout. See similar questions...

The parts of the artificial hip may either be fixed to bone with a substance called Methyl Methacrylate (Bone cement), or they are pressfit in the bone with capacity for the bone to stick to the parts. This Uncemented hip is used mainly for younger individuals. See similar questions...

You should tell your breeder if you are looking for a conformation show puppy or a companion/pet puppy. Most good breeders consider ALL of their puppies to be companion puppies, and Border Terrier people will tell you that Borders can do it all-obedience, agility, earthdog, tracking, flyball, therapy dog, etc.. A conformation show puppy is one whose physical characteristics and temperament meet or exceed the requirements of the breed standard. See similar questions...

The earlier units only had 1/4" inputs and outputs. Inputs are fully balanced, outputs are single-ended (some say "quasi-balanced") auto balancee/unbalanced. Ability to drive longer cables is less and high frequency rolloff can be a concern due to cable capacitance. Around 1994 we updated the design and changed to the "B" designation. These units have fully balanced inputs and outputs, both XLR and 1/4" TRS connections being utilized. Functionally the units are virtually identical. See similar questions...

An immigrant visa is the one that allows a foreigner to immigrate to the United States. For details please visit the internet page at http://www.usembassy.kz/consular/iv.shtml on immigrant visas. A non-immigrant visa can be issued to an alien who wants to travel to the U.S. for a temporary stay. There are several different categories of non-immigrant visas (tourist, student, etc.). Please refer to the Visa Category Chart and the section on non-immigrant visas. See similar questions...

Cash Contributions: Cash Contributions are considered to be those made by cash, check or credit card. The use of these gifts may be either restricted or unrestricted. These gifts may be the part of an outright (current) gift or a planned gift. Non-Cash Contributions: Non-Cash Contributions include such items as securities, real property, and/or personal property. These gifts may be restricted or unrestricted. See similar questions...

A matriculated student is a student who has filed an application to be admitted to a degree or certificate program, has been officially accepted, and has registered for the specific term for which he or she has been accepted. Matriculated students may attend on a full-time or part-time basis. A non-matriculated student is one who has enrolled in one, but no more than two credit courses, and has not been admitted as a degree or certificate candidate in any program within the college. See similar questions...

Priority III (Residential streets are only sanded at intersections & on rare occasions bends & curves are done.Icy conditions around water main breaks will be sanded as required) See similar questions...

Yes, you can sand veneer. Even though ours are sanded during manufacturing, finish sanding is recommended to achieve the best results when staining or clear coating. See similar questions...

The realm of non-producers consist of markets, stock shows, fairs, and other marketing intermediaries. In contrast, a producer is an animal owner Stake holder's must understand which title they fall under so they can properly register for a Wyoming premises identification. Two different applications are used (one for a producer and another for non-producers). Return to Top See similar questions...

Exempt and non-exempt status are determined by the Fair Labor Standards Act (FLSA) . This law regulates which positions are non-exempt (from the overtime provisions) and required to receive compensatory time or overtime wages for hours worked in excess of forty (40) hours per week. Per the law, hours worked over forty (40) are compensated at time and one half. See similar questions...

Apply a small area at a time, using a proper tiling rubber squeegee. Clean off excess immediately using clean water and a proper tile sponge. When dry, polish tiles with a cloth for that professional finish. See similar questions...